It exposes I/O resources to user space, so that programs can peek
and poke at the hardware. It does not itself have knowledge about
the hardware device it attaches to.
Sponsored by: Juniper Networks, Inc.
NetFPGA-10G Embedded CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA/AFRL
This code was heavily broken few months ago during CAM locking changes.
Fixing it would require almost complete rewrite. Since there are no
known devices on market using this interface younger then ~15 years, and
they are CD, not even DVD, I don't see much reason to rewrite it.
This change does not mean those devices won't work. They will just work
slower due to inefficient disks load/unload schedule if several LUNs
accessed same time.
Discussed with: ken@
Silence on: scsi@, hardware@
MFC after: 1 week
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
As a prerequisite for multiple queues, the guest must have MSIX enabled.
Unfortunately, to work around device passthrough bugs, FreeBSD disables
MSIX when running as a VMWare guest due to the hw.pci.honor_msi_blacklist
tunable; this tunable must be disabled for multiple queues.
Also included is various minor changes from the projects/vmxnet branch.
MFC after: 1 month
AppleTalk was a network transport protocol for Apple Macintosh devices
in 80s and then 90s. Starting with Mac OS X in 2000 the AppleTalk was
a legacy protocol and primary networking protocol is TCP/IP. The last
Mac OS X release to support AppleTalk happened in 2009. The same year
routing equipment vendors (namely Cisco) end their support.
Thus, AppleTalk won't be supported in FreeBSD 11.0-RELEASE.
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
for FreeBSD standards. Very little, if any, content was
modified.
These are not yet linked to the build.
Submitted by: Abhishek Gupta (abgupta!microsoft dot com)
Sponsored by: The FreeBSD Foundation
- Support for double-tap and drag.
- Support for 2-finger horizontal scrolling which translates to page-back/forward events.
- Single finger tap is equivalent to a left-button press.
- Two-finger taps are mapped to the right-button click.
- Three fingers are mapped to middle button.
- Add sysctl to disable single finger tapping.
- Fix for multiple open of /dev/atp0
- Enhanced support for the Fountain/Geyser family by adding Geyser4.
- Update manual page.
Submitted by: Rohit Grover <rgrover1@gmail.com>
MFC after: 2 weeks
