ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
Fixed the I/O statistics
Allow WD1007 type controllers to work
Support MULTI-BLOCK I/O
Correct delay to use port 0x84, reading the status register
might not be a long enough delay.
Changed probe message to match SCSI type devices.
with individual devices for each type of sound card:
opl, sb, sbxvi, sbmidi, pas, mpu, gus, gusxvi, gusmax, mss, uart
EXCLUDE_* options are no longer required to be included in the config file.
They are automatically determined by local.h depending on the devices
included.
Move #includes in local.h to os.h so files are included in the proper
order to avoid warnings.
soundcard.c now has additional code to reflect the device driver
routines needed.
Define new EXCLUDE_SB16MIDI for use in sb16_midi.c and dev_table.h.
#ifndef EXCLUDE_SEQUENCER or EXCLUDE_AUDIO have been added to
soundcard.c and sound_switch.c where appropriate.
Probe outputs changed to reflect new device names.
Readme.freebsd not needed. Update sound.doc with new config instructions.
Reviewed by: wollman
$Id$ information, and other code to make sound driver compile and work
correctly with FreeBSD.
Integrate changes obtained from Sujal Patel. These changes are:
o local.h: reverse option logic from EXCLUDE_* to AUDIO_*
o pas2_mixer.c: small addition
o ad1848.c: minor change with macro names
o sequencer.c: minor change with note check
o many spelling corrections in comments in about every other file
messages like this:
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (wd0): <ST506>
wd0: size unknown, using BIOS values: 615 cyl, 4 head, 17 sec, bytes/sec 512
npx0 at 0xf0-0xff irq 13 on motherboard
npx0: changing root device to wd0a
^^^^^^
The spurious 'npx0: ' pops up if you have a 386 with a 387 FPU.
Make the sound configuration a little neater
(see /sys/i386/isa/sound/Readme.freebsd)
Add support for the Microsoft Sound Source.
Document the sound options again.
Submitted by: Sujal Patel <smpatel@wam.umd.edu>
Obtained from: Voxware
Let "grey delete" be a function key (default is 0x7f)
Fix the xor cursor again..
Made the backspace key generate del as default
Made CTRL-space generate nul as default.
compiler.
Be carefull about over usage of volatile, it really killed performance
in a few areas and there was a better place to make things volatile in
almost all cases. The driver can now receive at full speed without RNR
errors.
(a) bring back ttselect, now that we have xxxdevtotty() it isn't dangerous.
(b) remove all of the wrappers that have been replaced by ttselect
(c) fix formatting in syscons.c and definition in syscons.h
(d) add cxdevtotty
NOT DONE:
(e) make pcvt work... it was already broken...when someone fixes pcvt to
link properly, just rename get_pccons to xxxdevtotty and we're done
Include proper files for 2.x.
Remove old unused argument to ixreset (int uba)
Nolonger convert ether_type to host byte order.
Use arp_ifinit in place of arpwhohas.
Change cb_ias to be non volatile.
is close to 1000000 / 960 usec so the confusion probably didn't matter.
Test for COMCONSOLE before testing for RB_SERIAL so that the RB_SERIAL
test can be optimized away if COMCONSOLE is 1.
Simplify and Uniformize style of previous commit.
(b) add a function callback vector to tty drivers that will return a pointer
to a valid tty structure based upon a dev_t
(c) make syscons structures the same size whether or not APM is enabled so
utilities don't crash if NAPM changes (and make the damn kernel compile!)
(d) rewrite /dev/snp ioctl interface so that it is device driver and i386
independant
Removed screensavers from syscons, they are now LKM's. This makes it
possible to do some really "interesting" screensavers...
Fixed bug that sometimes caused garbage to appear when leaving
"scroll-lock" history.
Reformattet indentation, it got too deep for a normal 80 pos screen.
Split up in syscons.c & syscons.h for use with the saver-lkm's.
Temporarily removed -s option from vidcontrol, savers should now
be loaded with modload.
returned to user mode without enabling ASTs. The problem fixed itself
at the next syscall or non-FPU trap, if any. It hung the system for
a test process that masked SIGFPE's and divided by zero. The faulting
division was returned to endlessly and this gave plently of opportunities
for the swi_ast_phantom case to be reached; after it was reached the
system hung because the ASTs for preemption and SIGINT handling were
disabled.
briefly over it, and see some serious architectural issues in this stuff.
On the other hand, I doubt that we will have any solution to these issues
before 2.1, so we might as well leave this in.
Most of the stuff is bracketed by #ifdef's so it shouldn't matter too much
in the normal case.
Reviewed by: phk
Submitted by: HOSOKAWA, Tatsumi <hosokawa@mt.cs.keio.ac.jp>
Slice 0 is now for the first BSD slice. The first BSD slice is
the first DOSpartition with id 0xa5 or the whole disk if their
are no DOSpartitions (except the latter is not yet implemented).
Existing partitions on it work the same as in 2.0 except the
'd' partition is no longer special and partitions are relative
to the skice.
Slice 1 is now for the whole disk and gets a read-only label
describing the disk. Previously, slice 0 was for the whole disk
and there was no label on it.
Slices 2-31 are for DOSpartitions. Slice 0 is an alias for one
of these if there is a BSD slice. Previously, slices 1-31 were
for DOSpartitions.
diskslice_machdep.c:
Expand whole disk slice to include all DOSpartitions. More work
is required for >1024 cylinders and to rewrite the label iff the
driver is unsure about the geometry.
subr_diskslice.c:
New function dsisopen() to help handle media changes.
when ttselect() is improved. This requires using an array of tty structs
and not using ttymalloc().
Fix an off by 1 error. Some caclulations seem to be off by a factor
of NCY. NCY defaults to 16, which gives 256 tty structs occupying
0xd000 bytes. The minor number encoding only allows 16 ttys.
Update the types of timeout functions to 2.0.
add a an ioctl call to set the transfer block size (SNDCTL_DSP_SETBLKSIZE)
and add the select system call to the drivers. They also fix a problem with
the #EXCLUDE macros for the PAS-16 card.
Submitted by: Jim Lowe <james@blatz.cs.uwm.edu>
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
You will normally have to have a VLB or other 32bit IDE "controller" for
this to work.
Depending on your setup, this may gain you 20-100 % speed from your disk.
Reviewed by: phk
Submitted by: vak@cronyx.ru
Display update method changed, now allways write in memory buffer,
then periodically update physical display.
Speed improvements (now > 5 times faster than the old syscons).
History now circular buffer, with changeable size.
History scroll by up/down line, up/down page, home and end.
Backtab proberly implemented.
Now space for 96 function keys, 63 allocated standard, default now
SCO/SYSV compat again as in the old days.
New keyboard definition files ~share/syscons/keymaps/*
Misc fixes for old "hacks" that broke SCO/SYSV compat.
More that I forgot before writing this...
Handles at least Trantor T130 and ProAudioSpectrum adapters.
The pas driver has consequently been removed.
This driver can be configured without without interrupts.
Manpage to follow when PAS16 has been edited in.
Reviewed by: phk
Submitted by: Serge Vakulenko, <vak@cronyx.ru>
case, software cursor now optional case. Driver must provide
raw things (what hardware do for us, exactly) as default case,
all driver features must be _optional_. Modern VGAs have internal
configuration utilities to set cursor shape/blinking which stored
into cards ROM, and syscons nuke out such features completely
by forcing software cursor. Moreover, software cursor is hard
to distinguish on standouted (or near standouted) fields and
tends to disappearse from the screen.
Set "flags 0x4" to enable software cursor now.
o Cleanup screen savers.
o Don't draw cursor if saver or blinker is active.
o Duplicated code moved to functons.
o Add more checks for blinker in progress, character lost otherwise
when blinker restore old contents.
o Reduce blinking counter to 3, too slow in old variant.
o Fix timeout code in scrn_timer(), old variant can reenter iself,
if action takes too long time.
o Disable visual bell for scroll lock mode, saved screen
becomes overwritted otherwise.
(Boot with the -D flag if you want symbols.)
Make it easier to extend `struct bootinfo' without losing either forwards
or backwards compatibility.
ddb_aout.c:
Get the symbol table from wherever the loader put it.
Nuke db_symtab[SYMTAB_SPACE].
boot.c:
Enable loading of symbols. Align them on a page boundary. Add printfs
about the symbol table sizes.
Pass the memory sizes to the kernel.
Fix initialization of `unit' (it got moved out of the loop).
Fix adding the bss size (it got moved inside an ifdef).
Initialize serial port when RB_SERIAL is toggled on.
Fix comments.
Clean up formatting of recently added code.
io.c:
Clean up formatting of recently added code.
netboot/main.c, machdep.c, wd.c:
Change names of bootinfo fields.
LINT:
Nuke SYMTAB_SPACE.
Fix comment about DODUMP.
Makefile.i386:
Nuke use of dbsym.
Exclude gcc symbols from kernel unless compiling with -g.
Remove unused macro.
Fix comments and formatting.
genassym.c:
Generate defines for some new bootinfo fields. Change names of old ones.
locore.s:
Copy only the valid part of the `struct bootinfo' passed by the loader.
Reserve space for symbol table, if any.
machdep.c:
Check the memory sizes passed by the loader, if any. Don't use them yet.
bootinfo.h:
Add a size field so that we can resolve some mismatches between the loader
bootinfo and the kernel boot info. The version number is not so good for
this because of historical botches and because it's harder to maintain.
Add memory size and symbol table fields. Change the names of everything.
Hacks to save a few bytes:
asm.S, boot.c, boot2.S:
Replace `ouraddr' by `(BOOTSEG << 4)'.
boot.c:
Don't statically initialize `loadflags' to 0. Disable the "REDUNDANT"
code that skips the BIOS variables. Eliminate `total'. Combine some
more printfs.
boot.h, disk.c, io.c, table.c:
Move all statically initialzed data to table.c.
io.c:
Don't put the A20 gate bits in a variable.
in the PCnet/Lance family.
Fix attach so 32 bit cards don't call isa_dmacascade.
Add a workaround for 32 bit chips which incorrectly truncate the
ring buffer size.
Fix a bug where CRC errors were reported as framming errors.
Change copyright to a BSD style one.
Obtained from:
sio.c and sioreg.c changed to allow autodetecting the RB_SERIAL flag
passed by the boot blocks so that the kernel can switch to 'serial
console' mode automagically. 'options COMCONSOLE' can still be specified
to force the kernel to always use the serial port as a console.
CONUNIT and CONADDR can also be specified in the kernel config file
if the user wants to shift the console to a different port.
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
properly from the beginning:
1) The `kern_devconf' struct should be a part of the driver's
`softc' structure (now it is).
2) The `description' should say what the device actually is,
rather than just giving a model number (now it does).
3) The device should be registered even if the probe fails, so
that it can be reconfigured later.
4) For netifs, the device state should follow the IFF_UP flag.
Other network interfaces should follow this example. (Please?) Eventually
there should be a rundown routine doing the equivalent of setting IFF_UP
off, and perhaps more if warranted.
protected drive at open() time has been *totally bogus*! The guy who
submitted it didn't understand all the implications of calling
set_motor(), and the `who' who included the patch into the tree did it
blindly... Pleeeeze, don't commit code to this driver unless you are
really going to understand what it does! This one caused me to pull
out even more hears, and those who know me do know that i ain't got
too many o'them. :-)
No kernel config options anymore besides keyboard language layout.
Virtual consoles are now dynamically allocated, no NCONS anymore.
Software cursor blinking/nonblinking.
Visual bell for laptops (don't beep at meetings :-).
Cursor/bell default type setable via config "flags" instead of as defines.
Cursor/bell type setable via ioctl's.
New video modes 80x30 80x60 for some laptops, and those with multisync monitors.
Scroll-lock history (length currently fixed at 100 lines).
Lots of cleanups, some only commented out for now (will goaway soon).
Support for new features in vidcontrol/kbdcontrol.
Updated manpages.
now marked busy as long as it's being in non-reset state, and the
drives are busy as long as at least one instance is open.
Also reformat everything to fit into 80 columns again.
Changed my mind wrt. error reporting for a write-protected drive and
an open() with write intent; ENXIO has been too weird, now return EIO.
Some portions of the code need to be rewritten to use tprintf()
instead of simple printf()'s, so the messages will also appear on the
session terminal, however.
Wangtek PC-02 QIC-02 controller with Cipher 150MB tape drive
Any attemp to open /dev/rwt0 hangs.
The following patch to /sys/i386/isa/wt.c is derived from Mikael
Hybsch's wt driver.
Submitted by: Terry Lee <terry@uivlsi.csl.uiuc.edu>
shifting. Also correct the original code as Garrett noticed it in mail.
Leave the mishandled code in to use it later if future versions of gcc
are correct. The code was part of the calibrate_cyclecounter routine to
get the speed of the pentium chip.
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.
Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.
Submitted by: (mostly) Peter Dufault <dufault@FreeBSD.org>
no more DOS boots to start it up.
Simply did a localized nuke of the OUTB macro in this file. This is
a kludge, since it seems it may actually be necessary in other GUS
files (tbd).
Thanks to: Amancio Hasty & Ken Hornstein
correct console number for the VT_WAITACTIVE ioctl. Invalid console numbers
caused waiting on an invalid pointer.
Use bcopyw() instead of move_up() and move_down(). bcopyw() handles
overlapped copies and should be faster. Actually use bcopy(). bcopy()
is slightly faster if video memory is 16-bit and about twice as fast if
it is 32-bit. bcopy() is said to fail on someGA's, but syscons already
depends on it working for other accesses to video memory.
Remove bogus input operands for fnsave(), fnstcw() and fnstsw().
Change all fwait's to fnop's. This might help avoid hardware bugs.
Wait after fninit with an fnop. This should be safer now.
Fix some spelling and formatting errors.
Use natural sizes for control and status words (u_short, promotes to int).
Don't clobber the SWI_CLOCK_MASK bits in npx0_imask when using IRQ13.
Set the devconf state correctly (always busy, if configured). Improve
code for npx_registerdev() a little (gcc can't keep id->id_unit in a
register for some reason). Don't register a nonexistent npx device.
Print a useful message in npxattach() again (delete references to errors
and not the whole message). Don't print "387 emulator" if there is no
emulator in the kernel.
Use %p for pointers in error messages.
Don't clobber the FPU state when there is an FPU exception. Just clear
the exception flags (after saving the flags as before). This allows
debuggers and SIGFPE handlers to look at the full exception state.
SIGFPE handlers should normally return via longjmp(), which restores a
good FPU state (as before). Returning from a SIGFPE handler may leave
the FPU in the wrong state (as before).
Clear the busy latch _after_ clearing the exception flags so that there
is less chance of getting a bogus h/w interrupt for a control operation.
Clear the saved exception status word when the next FPU instruction is
excuted so that it doesn't stick around until the next exception.
Clear the busy latch after fnsave() in npxsave() in case it was set when
npxsave() was called.
values for syncronous negotiation. The 284x series adaptors can now be
supported without the Bios being enabled. If you disable the Bios on the
274x series adaptors, all configuration parameters revert to the default
since there is no way to retrieve them.
- /sys/i386/isa/if_ed.c doesn't quite know how to deal with SMC EtherEZ
ethernet cards. The EtherEZ looks just like the Elite Ultra, except it
has only 8K of shared memory. The only way to have it properly detected
is to zero and test a few bytes of memory just about the first 8K region.
If it clears properly, it's an Elite Ultra, otherwise it's an EtherEZ.
I've also got an EtherEZ patch for netboot (Makefile, ether.c and ether.h).
- /sys/i386/isa/syscons.c wraps at the next to the last column rather than
the last column, like it should. You don't really notice this unless you
use certain programs that write all the way out to, say, the 80th column,
like VMSmail. Along with a one-line fix for this are some changes to
implement a non-blinking cursor. Put 'options "NOBLINK_CURSOR"' in your
config file and give it a try. :)
Submitted by: wpaul
Would you please commit this two-line patch to /sys/i386/isa/b004.c
(the Transputer driver) so that it at least compiles under 2.x
Haven't tried if the driver is working properly, but a kernel with
compiled-in driver has been running for two days now with no apparent
problems.
Submitted by: luigi
This is new version of Seagate ST01/02, Future Domain TMC-885, TMC-950
SCSI driver for FreeBSD. I started from the 2.0R version and mostly
rewrote it. New features are:
1) New probe algorithm. Old driver read the BIOS region of the adapter
memory and find the copyright string. The problem was in the BIOS itself:
it conflicted with IDE disks. The solution was to unplug it and
make the probe algorithm to work without it.
2) Proper timeout handling in numerous places where the driver
polls waiting for some event.
3) Assembler flagments added in critical places, mostly for data transfer
to of from the target. It was possible to make it faster,
but at the price of decreasing reliability.
4) Target-dependent delays when waiting for REQ deassert event.
Some devices seem to be slower (CD-ROMS, some tape drives),
and some seem to be too fast (disks). The driver tests the REQ
deassert timeout for each target and then uses it for polling.
5) Device flags added for SCSI parity control and sense request
priority control.
6) Generic cleanup, after which the driver became much more readable
(at least by me:).
7) Target data parity error logging is limited to avoid log file overflow.
8) Manual page added.
Submitted by: serge
Move definition of `stat_imask' to clock.c.
clock.c:
Rename `rtcmask' to `stat_imask' and export it. Rename `clkmask' to
`clk_imask' for consistency.
Only calculate TIMER_DIV(hz) once.
Merge debugging and "garbage" code to produce debugging code and format the
output better.
Make writertc() static inline and use it everywhere. Now all accesses to
the clock registers go through rtcin() and writertc().
Move rtc initialization to cpu_initclocks().
Merge enablertclock() with cpu_initclocks() and remove enablertclock().
The extra entry point was just a leftover from 1.1.5.
for wd (they both count the number of sectors). The wpms stat is still
moderately bogus for all drivers. Even the count stat could be handled
better (partial blocks should be counted as full blocks; should errors
and retries be counted?).
Voxware hackers should feel free to work on this some more, it's by no means
a perfect product.
(I have patches for GUS users running 2.x to run their GUS with bidirectional
DMA (talk while listening. All other soundboards must use push-to-talk until
people learn to build real hardware).
Submitted by: amancio hasty & paul traina
<string.h> isn't supposed to be used by the kernel.
cronix.h is <machine/cronix.h>, not "cronyx.h" (ambiguous) or
<sys/cronyx.h> (nonexistent; caused compile to fail).
cxreg.h is <i386/isa/cxreg.h>, not "cxreg.h".
<i386/isa/cpufunc.h> shouldn't be included directly; it is always
included by <sys/systm.h>.
<i386/include/*.h> is <machine/*.h>
<systm.h> is <sys/systm.h>.
<kernel.h> is <sys/kernel.h>.
<bpfilter.h> is "bpfilter.h". It really is in the current directory.
>Description:
If a process attempts to open a floppy tape device when the
device has been configured in the kernel, but did not probe and attach
on bootup, then a panic will occur.
[Review: The current ft situation is a crock, and this only bandaids
an earlier wound inflicted by making the attach conditional. This urgently
requires a review]
Submitted by: gene
Keep track of interrupt nesting level. It is normally 0
for syscalls and traps, but is fudged to 1 for their exit
processing in case they metamorphose into an interrupt
handler.
i386/genassym.c;
Remove support for the obsolete pcb_iml and pcb_cmap2.
Add support for pcb_inl.
i386/swtch.s:
Fudge the interrupt nesting level across context switches and in
the idle loop so that the work for preemptive context switches
gets counted as interrupt time, the work for voluntary context
switches gets counted mostly as system time (the part when
curproc == 0 gets counted as interrupt time), and only truly idle
time gets counted as idle time.
Remove obsolete support (commented out and otherwise) for pcb_iml.
Load curpcb just before curproc instead of just after so that
curpcb is always valid if curproc is. A few more changes like
this may fix tracing through context switches.
Remove obsolete function swtch_to_inactive().
include/cpu.h:
Use the new interrupt nesting level variable to implement a
non-fake CLF_INTR() so that accounting for the interrupt state
works.
You can use top, iostat or (best) an up to date systat to see
interrupt overheads. I see the expected huge interrupt overheads
for ISA devices (on a 486DX/33, about 55% for an IDE drive
transferring 1250K/sec and the same for a WD8013EBT network card
transferring 1100K/sec). The huge interrupt overheads for serial
devices are unfortunately normally invisible.
include/pcb.h:
Remove the obsolete pcb_iml and pcb_cmap2. Replace them by
padding to preserve binary compatibility.
Use part of the new padding for pcb_inl.
isa/icu.s:
isa/vector.s:
Keep track of interrupt nesting level.
Now floppy tape support is *disabled* unless you specifically
request otherwise. Poul wanted it this way, and I guess I'm not going to argue
though it may seem counter-intuitive. We can always change it back, later.
flags & 0x1. Somebody should build a kernel with this and see if
the floppy-tape damaged people can turn it off properly with userconfig.
I can't reproduce the original problem here.
and into ether_input(). It was silly to have bpf want this one way and
ether_input want it another way. Ripped out trailer support from the few
remaining drivers that still had it.
That was the good news. The bad news is that bad144 is a proper mess,
and I don't have time to fix it now, so you will probably not be able to
use it anyway.
Sorry guys, go out and buy a 100Mb IDE drive and a paddleboard :-(
If somebody wants to pick up on this: bad144 needs to learn how to
stay inside our slice of the disk. That's the trick.
Somehow, I don't think this stuff was tested at all! :-(
I really hope that it actually works, though my hopes are steadily diminishing.
Anyone with 27xx/28xx boards in -current is *strongly encouraged* to give this
stuff a shot! Otherwise, I suspect that we'll be punting this out of
2.0. I haven't found a single part of Justin's commit that wasn't broken
in some way.
Remove bogus declaration of Debugger(). Call Debugger() even if DDB is
not defined, but still call panic() after Debugger() returns, although
most other SCSI drivers just call Debugger().
with the current default exception (un)mask. There should be no such
processes unless you change the mask. Someday the mask should be
changed to the IEEE default of everything masked. The npx state
gets saved so that it can be checked and this may have the side effect
of fixing a bug that was reported for 1.1.5. (npx exceptions may
sometimes leak across exits and clobber another process. I can't see
how this can happen.)
Get some missing/wrong declarations from headers now that the headers
have them.
of the 1.1.5 driver, a recent version of the NetBSD driver, Andres'
transmission start threshold code, and all other relavent changes to the driver
since it was brought into 2.0. The multicast support from NetBSD has not be
folded in yet. I've tested it under high loads for two weeks and it is now
robust enough to be included in the GENERIC kernel.
Reviewed by: gibbs
Submitted by: vega@sophia.inria.fr (Andres Vega Garcia)
cosmetique) because we already have right things there or his changes
are incorrect.
Fix mcd_subchan to return position, inspired by idea from
bugress@s069.infonet.net, but different implementation.
Here is the improved probe for the mse (Bus Mouse) device driver. I
have been running with this under 1.1.5.1 as well as 2.0 without a hitch for
quite a while.
Submitted by: lars
tsleep()). Try `dd if=/dev/zero of=/dev/pcaudio bs=640k count=1'. The
write takes a few hundred seconds to drain, and if it is killed by a
signal, it still takes a few hundred seconds to drain and all of those
seconds are spent busy-waiting.
Clean up includes and declarations. Remove bogus casts of args to
timeout functions.
doesn't have to calculate it every call.
Rename `timer0_prescale' to `timer0_prescaler_count' and maintain it
correctly. Previously we lost a few 8253 cycles for every "prescaled"
clock interrupt, and the lossage grows rapidly at 16 KHz. Now we
only lose a few cycles for every standard clock interrupt.
Rename `*_divisor' to `*_max_count'.
Do the calculation of TIMER_DIV(rate) only once instead of 3 times each
time the rate is changed.
Don't allow preposterously large interrupt rates. Bug fixes elsewhere
should allow the system to survive rates that saturate the system, however.
Clean up declarations.
Include <machine/clock.h> to check our own declarations.
floppies now. I'm not sure why, but things hang when it gets to the
`changing root to fd0c' part. Without your latest commit, everything works
fine. Maybe you can figure out what you broke after ALPHA! :)
errors at a lower ipl. clist starvation problems can cause hundreds of
tty buffer overflows per second and logging them all amplified the
problems. This problem was less serious in 1.1.5.
Avoid a race in the check for starting a new block of output. com_events
was sometimes messed up and siopoll() looped endlessly. This bug was
introduced in 2.0.
Clean up previous 2 commits. Rename sio_registerdev() to sioregisterdev()
to match the (bad) surrounding naming conventions. There should be a
generic_registerdev().
. avoid resetting the FDC every time the last motor is going off;
instead, give it a 60-second period for possible later reactivation.
This prevents us from needing to recalibrate the FDC too often,
but still allows for an ``automagic error recovery', just in case the
controller is absolutely stuck. (Simply wait for 60 seconds, and
try it again.)
. made the floppy head settle time after a seek a constant
that might be overridden by a config option. (Well, actually the
divisor of the settle time). Pepople often reported problems with
their floppies, so i need a simply mechanism that allows them
to play with that value. (I personally cannot find any problem
on *my* drives.)
. implement the FD_DEBUG ioctl command, in case the driver
is compiled with DEBUG turned on.
. removed a bogus parameter from a printf; the remaining warnings
from gcc -Wall seem to be warnings about the %b format gcc cannot
understand
. rearrange Garett's code to fit better in the existing structure
of #define/type/function ordering.
. make everything fit into 79 columns again.
in the far pointers are multiples of 4K (as is normal when the video
BIOS is at seg 0xc000). Disallow mode switching if the pointer is bad.
Use a new pa_to_va() macro for all BIOS and video addresses in syscons.
Changed the fifth parameter to register_intr() from u_int mask into
u_int *maskptr in preparation for new features (shared interrupts and
removable devices, eg. for PCMCIA).
Changed the fifth parameter to register_intr() from u_int mask into
u_int *maskptr in preparation for new features (shared interrupts and
removable devices, eg. for PCMCIA).
and all SCSI devices (except that it's not done quite the way I want). New
information added includes:
- A text description of the device
- A ``state''---unknown, unconfigured, idle, or busy
- A generic parent device (with support in the m.i. code)
- An interrupt mask type field (which will hopefully go away) so that
. ``doconfig'' can be written
This requires a new version of the `lsdev' program as well (next commit).
One of the alpha testers (ETO, Toshihisa <eto@osl.fujitsu.co.jp>)
of my APM driver sent me a very small patch to if_ze.c for using IBM
PCMCIA Ethernet card II. There are only a few difference between
Ethernet card I and II. So we can use them both with this patch. It
also includes a patch for PCIC of ThinkPad 230Cs (As long as I
remember, this model is available in Japan only. But it is very
popular subnote in Japan).
Submitted by: hosokawa
so i hope i've finally removed all the occasions where the driver
got stuck when there's no floppy in the drive.
Also attemmpting to omit the error mesage for ``recalib failed''
for the first time, since people tend to be confused about this.
drivers have a chance to change their IRQ before it is checked.
This was implemented in revision 1.21 and broken in revision 1.26.
Drivers that can change their IRQ should probably be configured
with "irq ?".
else has been probed. This feature could go away again, if we can curb the
problem another way.
if_ed.c, syscons.c: Set the above flag. ed# because it needs it, syscons
because it looks stupid to "detect" the display you have already filled up
with text :-)
bt742a.c: Check bt_cmd() return-val during probe, thus failing on adaptec's.
Also silenced various printf's during the probe.
isa.c: Probe devices with the above flag set before the rest. Reduce the
number of "conflict" messages per device to one.
***
Please test the GENERIC-kernel now, if nobody can make it fail, GENERICAH
and GENERICBT has a finite and short life-expectancy...
***
of mb_offset given the right sequence of 1 and 0 byte mbufs. This bug
was discovered by John Hood who also provided this fix - which is a
rewrite of the routine (and is easier to understand than the code I wrote).
Submitted by: John Hood <cgull@smoke.marlboro.vt.us>
Fix endless loop in siopoll() for an event on a tty with no tty struct.
Don't generate unwanted interrupts in the serial console driver. These
bugs probably don't matter unless the tty struct is dynamically allocated.
Support polled mode. To use it, leave out the irq and the vector in
the config file. It only causes extra overhead for open polled ports.
The maximum usable speed is approximately 1000 bps for a 16450 and
15000 bps for a 16550.
Other cosmetic changes.
the first place was so that BPF could grok trailer packets. I've since
decided that this is a job for tcpdump to decipher (if at all). Also
fixed up checks for received packet length to better cope with ancient
starlan boards.
Submitted by: Thomas David Rivers <rivers%ponds@ncren.net>
WARNING: might hide some bug below! I commit this to improve the stability
of 2.0.
Thomas wrote:
-------------
I have been running a kernel with this change since October 4th; barring
unrelated network router troubles, the pitiful little machine has
completed several builds without any interaction from me, and continues
to chug along.
I re-read wd.c, and added appropriate printfs() to look for references
to dk_badsect[]. My changes should have printed something when dk_badsect[]
was referenced.
I got no output :-(
Thus, I'm forced to concluded that something else is examining some
spurious memory... which happened to be in dk_badsect[] of the disk structure
in wd.c. I can find no other explanation of why this unnecessary
initialization causes things to operate correctly.
On the premise that such an initialization isn't going to hurt anything,
I'm going to suggest it go into 2.0.
I'd like to thank everyone for there assistance, particularly David,
John and Bruce.
be merged at some point)
New AMD family ethernet driver. Should support BICC,NE2100, TNIC,
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
