An optical disk may not have a TOC (e.g. for blank media) and userland
software may legitimately try to use CDIOREADTOCHEADER to find out about
the TOC.
Silence from: scsi@
MFC after: 10 days
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
camcontrol.c: In buildbusdevlist(), don't attempt to get call
getdevid() for an unconfigured device, even when the
verbose flag is set. The cam_open_btl() call will almost
certainly fail.
Probe for the buffer size when issuing the XPT_GDEV_ADVINFO
CCB. Probing for the buffer size first helps us avoid
allocating the maximum buffer size when it really may not
be necessary. This also helps avoid errors from
cam_periph_mapmem() if we attempt to map more than MAXPHYS.
cam_periph.c: In cam_periph_mapmem(), if the XPT_GDEV_ADVINFO CCB
shows a bufsiz of 0, we don't have anything to map,
so just return.
Also, set the maximum mapping size to MAXPHYS
instead of DFLTPHYS for XPT_GDEV_ADVINFO CCBs,
since they don't actually go down to the hardware.
scsi_pass.c: Don't bother mapping the buffer in XPT_GDEV_ADVINFO
CCBs if bufsiz is 0.
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
Add the BIO_ORDERED flag for struct bio and update bio clients to use it.
The barrier semantics of bioq_insert_tail() were broken in two ways:
o In bioq_disksort(), an added bio could be inserted at the head of
the queue, even when a barrier was present, if the sort key for
the new entry was less than that of the last queued barrier bio.
o The last_offset used to generate the sort key for newly queued bios
did not stay at the position of the barrier until either the
barrier was de-queued, or a new barrier (which updates last_offset)
was queued. When a barrier is in effect, we know that the disk
will pass through the barrier position just before the
"blocked bios" are released, so using the barrier's offset for
last_offset is the optimal choice.
sys/geom/sched/subr_disk.c:
sys/kern/subr_disk.c:
o Update last_offset in bioq_insert_tail().
o Only update last_offset in bioq_remove() if the removed bio is
at the head of the queue (typically due to a call via
bioq_takefirst()) and no barrier is active.
o In bioq_disksort(), if we have a barrier (insert_point is non-NULL),
set prev to the barrier and cur to it's next element. Now that
last_offset is kept at the barrier position, this change isn't
strictly necessary, but since we have to take a decision branch
anyway, it does avoid one, no-op, loop iteration in the while
loop that immediately follows.
o In bioq_disksort(), bypass the normal sort for bios with the
BIO_ORDERED attribute and instead insert them into the queue
with bioq_insert_tail(). bioq_insert_tail() not only gives
the desired command order during insertion, but also provides
barrier semantics so that commands disksorted in the future
cannot pass the just enqueued transaction.
sys/sys/bio.h:
Add BIO_ORDERED as bit 4 of the bio_flags field in struct bio.
sys/cam/ata/ata_da.c:
sys/cam/scsi/scsi_da.c
Use an ordered command for SCSI/ATA-NCQ commands issued in
response to bios with the BIO_ORDERED flag set.
sys/cam/scsi/scsi_da.c
Use an ordered tag when issuing a synchronize cache command.
Wrap some lines to 80 columns.
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/vdev_geom.c
sys/geom/geom_io.c
Mark bios with the BIO_FLUSH command as BIO_ORDERED.
Sponsored by: Spectra Logic Corporation
MFC after: 1 month
This makes things easier for target implementations to calculate how many
elements they need to allocate.
Discussed with: mjacob, gibbs
MFC after: 1 week
the case of immediate unconfigure after configure. Hold the periph an
extra count while we have the task to create sysctl context outstanding
so that the periph doesn't go away unexpectedly.
Sponsored by: Panasas
Reviewed by: scsi@
MFC after: 1 month
better devices. This can be disabled on a per-device basis using quirks as
well.
This also handles the case where there is actually no connected LUN 0
(which can definitely be the case for storage arrays).
Reviewed by: scsi@
MFC after: 1 month
for REPORT and SET TARGET PORT GROUP commands (foundations for future work).
Regularize opcodes to be upper case hex.
Pick *one* of tab or space after #define (tab) and stick with that.
MFC after: 2 weeks
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
d_mediasize
CD_FLAG_VALID_TOC is not required for setting those media properties.
PR: kern/145385
Submitted by: Juergen Lock <nox@jelal.kn-bremen.de>
a slightly different version
Tested by: Pavel Sukhoy <sukhoy@ripn.net>,
Markus Wild <m.wild@cybernet.ch>,
Juergen Lock <nox@jelal.kn-bremen.de>,
uqs
MFC after: 1 week
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
- Move tagged queueing control from ADA to ATA XPT. It allows to control
device command queue length correctly. First step to support < 32 tags.
- Limit queue for non-tagged devices by 2 slots for ahci(4) and siis(4).
- Implement quirk matching for ATA devices.
- Move xpt_schedule_dev_sendq() from header to source file.
- Move delayed queue shrinking to the more expected place - element freeing.
- Remove some SCSIsms in ATA.
- Remove CAM_PERIPH_POLLED flag. It is broken by design. Polling can't be
periph flag. May be SIM, may be CCB, but now it works fine just without it.
- Remove check unused for at least five years. If we will ever have non-BIO
devices in CAM, this check is smallest of what we will need.
- If several controllers complete requests same time, call swi_sched()
only once.
disk is first probed. dagetcapacity is called whenever the disk is opened from
geom via d_open(), a zero sector size will cause geom to panic later on.
Fix reference counting bug, when device unreferenced before then
invalidated. To do it, do not handle validity flag as another
reference, but explicitly modify reference count each time flag is
modified.
Discovered by: thompsa
- Reduce code duplication in ATA XPT and PMP driver.
- Move PIO size setting from ada driver to ATA XPT. It is XPT business
to negotiate transfer details. ada driver is now stateless.
- Report PIO size to SIM. It is required for correct PATA SIM operation.
- Tune PMP scan timings. It workarounds some problems with SiI.
- If reset hapens during PMP initialization - restart it.
- Introduce early-initialized periph drivers, which are used during initial
scan process. Use it for xpt, probe, aprobe and pmp. It gives pmp chance
to finish scan before mountroot and numerate devices in right order.
allocations M_NOWAIT so that we don't try and sleep with a nested non-sleepable
lock.
This makes the userland scsi_target begin to function again.
Obtained from: Sean Bruno
MFC after: 1 month
page_list using the matching malloc type for the allocation.
Approved by: re
Reviewed by: scottl [1]
MFC after: 1 week
[1] Original patch was against xpt_cam.c, prior to the cam refactoring.
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
vnode interlock to protect the knote fields [1]. The locking assumes
that shared vnode lock is held, thus we get exclusive access to knote
either by exclusive vnode lock protection, or by shared vnode lock +
vnode interlock.
Do not use kl_locked() method to assert either lock ownership or the
fact that curthread does not own the lock. For shared locks, ownership
is not recorded, e.g. VOP_ISLOCKED can return LK_SHARED for the shared
lock not owned by curthread, causing false positives in kqueue subsystem
assertions about knlist lock.
Remove kl_locked method from knlist lock vector, and add two separate
assertion methods kl_assert_locked and kl_assert_unlocked, that are
supposed to use proper asserts. Change knlist_init accordingly.
Add convenience function knlist_init_mtx to reduce number of arguments
for typical knlist initialization.
Submitted by: jhb [1]
Noted by: jhb [2]
Reviewed by: jhb
Tested by: rnoland
The device index number stored in the unit number of sa(4) devices is
only used to print debug messages. Get rid of this index number and use
devtoname() to just print the entire device name.
things around so the periph destructors look alike. Based on a patch
by Jaakko Heinonen.
Submitted by: Jaakko Heinonen
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
When trying to read scratched or damaged CDs and DVDs, the default
mechanism is sub-optimal. Programs like ddrescue do much better if
you turn off retries entirely, since their algorithms are designed
scan big areas fast, then winnow the areas down. Turning off retries
speeds these programs up by as much as 20x, since the drive is able to
'stream past' many small errors...
The sysctl/tunable kern.cam.cd.retry_count controls this. That
defaults to '4' (for a total of 5 attempts). Setting to 0 turns off
all retry attempts.
Reviewed by: scottl@
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
because the media was removed, the periph would get its refcount dropped
and ultimately freed before getting unlocked. This created a dangling
pointer that was easy to trip over. This fixes a common source of
crashes with removaable media, but problems remain and will get tracked
down.
http://www.t10.org/lists/1spc-lst.htm
Note opcodes for scanner and communication devices are taken from the previous
revision because they are not listed in the files any more.
Also, note newly added ASCs are all marked with 'XXX TBD' and take SS_RDEF action
for now. Some ASCs need SS_TUR for error recovery or SS_FATAL to prevent further
retrials. We should deal with them later.
Reviewed by: scottl, ken
the referenced data is only obtained/changed in the device open handler,
and the ioctl handler can only run after the open handler. Also fix a
few nearby style issues.
Submitted by: Matt Jacob
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
flash card reader.
Also remove an 'Opened da0 -> <random number>' which is not needed on a daily
basis (available through bootverbose).
Reviewed by: phk, ken
MFC after: 1 week
the ORDERED tag. This recoups significant performance gains for many
arrays.
The default is still to send out the ORDERED tag periodically.
Reviewed by: scsi (justin+timeout)
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
REPORT LUNS command to a device.
camcontrol.[c8]: Implement reportluns. This tries to print the LUNs
out in a reasonable format. Only the periph
addressing method has been tested, since very little
hardware that I know of supports the other methods.
scsi_all.[ch]: Revamp the report luns CDB structure and helper
functions. This constitutes a little bit of an API
change, but since the old CDB length was 10 bytes,
and the REPORT LUNS CDB length is actually 12 bytes,
it's clear that no one was using this API in the
first place.
MFC After: 1 week
usage as of SPC2r20. Specifically, handle the BQueue
flag which will indicate that a device supports the
Basic Queueing model (no Head of Queue or Ordered tags).
When this flag is set, SID_CmdQueue is clear. This has
causes FreeBSD to assume that the device did not support
tagged operations.
MFC after: 1 month
This version of scsi_target.c removes all SMP locking until
we have a lock-aware CAM stack. This allows us to use KNOTE
without a panic at least.
It's not yet clear whether target mode is working yet or not.
Discussed with: Scott, Ken, Nate, Justin
return to user space w/o waiting for I/O to complete.
I tried to get several folks who know this code better than me to review it
with no luck. I *do* know that w/o this code, using the SCSI target driver
panics in userret (if it doesn't panic in knote first).
an application to upon a tape (yea, even the non-control device) even if
it cannot establish a mount session. If the open cannot establish a mount
session and O_NONBLOCK was specified, the tape becomes 'open pending mount'.
All I/O operations that would require access to a tape thereafter until
a close attempt to initiate the mount session. If the mount session succeeds,
the tape driver transitions to full open state, else returns an appropriate
I/O error (ENXIO).
At the same time, add a change that remembers whether tape is being opened
read-only. If so, disallow 'write' operations like writing filemarks that
bypass the normal read-only filtering operations that happen in the write(2)
syscall.
Reviewed by: ken, justin, grog
MFC after: 2 weeks
Suggested by: The Bacula Team
the underlying drive had been hot-unplugged from the system. Here
is a specific example. Filesystem code had opened /dev/da1s1e.
Subsequently, the drive was hot-unplugged. This (correctly) caused
all of the associated /dev/da1* entries to be deleted. When the
filesystem later realized that the drive was gone it closed the
device, reducing the write-access counts to 0 on the geom providers
for da1s1e, da1s1, and da1. This caused geom to re-taste the
providers, resulting in the devices being created again. When the
drive was hot-plugged back in, it resulted in duplicate /dev entries
for da1s1e, da1s1, and da1.
This fix adds a new disk_gone() function which is called by CAM when a
drive goes away. It orphans all of the providers associated with the
drive, setting an error condition of ENXIO in each one. In addition,
we prevent a re-taste on last close for writing if an error condition
has been set in the provider.
Sponsored by: Isilon Systems
Reviewed by: phk
MFC after: 1 week
event handler, dev_clone, which accepts a credential argument.
Implementors of the event can ignore it if they're not interested,
and most do. This avoids having multiple event handler types and
fall-back/precedence logic in devfs.
This changes the kernel API for /dev cloning, and may affect third
party packages containg cloning kernel modules.
Requested by: phk
MFC after: 3 days
- Introducing the possibility of using locks different than mutexes
for the knlist locking. In order to do this, we add three arguments to
knlist_init() to specify the functions to use to lock, unlock and
check if the lock is owned. If these arguments are NULL, we assume
mtx_lock, mtx_unlock and mtx_owned, respectively.
- Using the vnode lock for the knlist locking, when doing kqueue operations
on a vnode. This way, we don't have to lock the vnode while holding a
mutex, in filt_vfsread.
Reviewed by: jmg
Approved by: re (scottl), scottl (mentor override)
Pointyhat to: ssouhlal
Will be happy: everyone
module-specific malloc types. These should help us to pinpoint the
possible memory leakage in the future.
- Implementing xpt_alloc_ccb_nowait() and replacing all malloc/free based
CCB memory management with xpt_alloc_ccb[_nowait]/xpt_free_ccb. Hopefully
this would be helpful if someday we move the CCB allocator to use UMA
instead of malloc().
Encouraged by: jeffr, rwatson
Reviewed by: gibbs, scottl
Approved by: re (scottl)
period value. I suppose the BT adapter driver should be
fixed, but more importantly we should protect against
dividing by zero.
PR: kern/75603
MFC after: 1 week
succeed if there was no media in the drive.
This was broken in rev 1.72 when the media check was added to cdioctl().
For now, check the ioctl group to decide whether to check for media or not.
(We only need to check for media on CD-specific ioctls.)
Reported by: bland
MFC after: 3 days
providing special version of CDIOCREADSUBCHANNEL ioctl(), which assumes that
result has to be placed into kernel space not user space. In the long run
more generic solution has to be designed WRT emulating various ioctl()s
that operate on userspace buffers, but right now there is only one such
ioctl() is emulated, so that it makes little sense.
MFC after: 2 weeks
sectorsize in order to avoid a lot of checks around various divisions etc.
Enforce the sectorsize being > 0 with a KASSERT on successful open.
Fix scsi_cd.c to return 2k sectors when no media inserted.
a more complete subsystem, and removes the knowlege of how things are
implemented from the drivers. Include locking around filter ops, so a
module like aio will know when not to be unloaded if there are outstanding
knotes using it's filter ops.
Currently, it uses the MTX_DUPOK even though it is not always safe to
aquire duplicate locks. Witness currently doesn't support the ability
to discover if a dup lock is ok (in some cases).
Reviewed by: green, rwatson (both earlier versions)
The big lines are:
NODEV -> NULL
NOUDEV -> NODEV
udev_t -> dev_t
udev2dev() -> findcdev()
Various minor adjustments including handling of userland access to kernel
space struct cdev etc.
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
Previously the "struct disk" were owned by the device driver and this
gave us problems when the device disappared and the users of that device
were not immediately disappearing.
Now the struct disk is allocate with a new call, disk_alloc() and owned
by geom_disk and just abandonned by the device driver when disk_create()
is called.
Unfortunately, this results in a ton of "s/\./->/" changes to device
drivers.
Since I'm doing the sweep anyway, a couple of other API improvements
have been carried out at the same time:
The Giant awareness flag has been flipped from DISKFLAG_NOGIANT to
DISKFLAG_NEEDSGIANT
A version number have been added to disk_create() so that we can detect,
report and ignore binary drivers with old ABI in the future.
Manual page update to follow shortly.
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
instead of retrying them blindly.
This should fix some of the problems people have been having with cdrom
drives taking a long time to probe. This should also eliminate the need
for the initial TUR in cdsize().
cam_periph.c: Don't keep retrying if the error we get back is a fatal
error. This should help us detect the transition from
"Logical unit not ready, cause not reportable" to "Medium
not present" in the "TUR many" handler. (The TUR many
handler gets triggered for Logical unit not ready, cause
not reportable errors.)
scsi_cd.c: Remove the initial test unit ready in cdsize(). Hopefully
it isn't necessary after the above change.
Submitted by: gibbs (mostly)
Tested by: peter
MFC After: 2 weeks
an uninitialized sysctl_ctx, using flag DA_FLAG_SCTX_INIT. This
prevents a panic encoutered with some umass units that probe correctly
but fail to attach. Same problem, and same fix, as scsi_cd.c rev. 1.86.
Reviewed by: njl, ken
has been initialized.
(cdsysctlinit): Set flag CD_FLAG_SCTX_INIT after sysctl_ctx has been
initialized.
This resolves a panic encountered when a cd drive is sucessfully probed
but fails to attach.
Reviewed by: ken
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
For the floppy driver, use fdcontrol to manipulate density selection.
For the CD drivers, the 'a' and 'c' suffix is without actual effect and
any applications insisting on it can be satisfied with a symlink:
ln -s /dev/cd0 /dev/cd0a
Ongoing discussion may result in these pieces of code being removed before
the 5-stable branch as opposed to after.
into targreadfilt(). Unlock around calls to notify_user(). If an application
is sending CCBs while the endpoint is shutting down, this may result in
incomplete disable. A more complete solution will come with a "dying" flag.
Submitted by: simokawa
out of cdregister() and daregister(), which are run from interrupt context.
The sysctl code does blocking mallocs (M_WAITOK), which causes problems
if malloc(9) actually needs to sleep.
The eventual fix for this issue will involve moving the CAM probe process
inside a kernel thread. For now, though, I have fixed the issue by moving
dynamic sysctl variable creation for these two drivers to a task queue
running in a kernel thread.
The existing task queues (taskqueue_swi and taskqueue_swi_giant) run in
software interrupt handlers, which wouldn't fix the problem at hand. So I
have created a new task queue, taskqueue_thread, that runs inside a kernel
thread. (It also runs outside of Giant -- clients must explicitly acquire
and release Giant in their taskqueue functions.)
scsi_cd.c: Remove sysctl variable creation code from cdregister(), and
move it to a new function, cdsysctlinit(). Queue
cdsysctlinit() to the taskqueue_thread taskqueue once we
have fully registered the cd(4) driver instance.
scsi_da.c: Remove sysctl variable creation code from daregister(), and
move it to move it to a new function, dasysctlinit().
Queue dasysctlinit() to the taskqueue_thread taskqueue once
we have fully registered the da(4) instance.
taskqueue.h: Declare the new taskqueue_thread taskqueue, update some
comments.
subr_taskqueue.c:
Create the new kernel thread taskqueue. This taskqueue
runs outside of Giant, so any functions queued to it would
need to explicitly acquire/release Giant if they need it.
cd.4: Update the cd(4) man page to talk about the minimum command
size sysctl/loader tunable. Also note that the changer
variables are available as loader tunables as well.
da.4: Update the da(4) man page to cover the retry_count,
default_timeout and minimum_cmd_size sysctl variables/loader
tunables. Remove references to /dev/r???, they aren't used
any longer.
cd.9: Update the cd(9) man page to describe the CD_Q_10_BYTE_ONLY
quirk.
taskqueue.9: Update the taskqueue(9) man page to describe the new thread
task queue, and the taskqueue_swi_giant queue.
MFC after: 3 days
commands. Add a quirk for the Creative Nomad MuVo USB device that uses
it as well as NO_SYNCHRONIZE_CACHE.
PR: kern/53094
Submitted by: Richard Nyberg <rnyberg@it.su.se>
MFC after: 3 days
to such devices. If a device fails due to this commit, add:
options DA_OLD_QUIRKS
to the kernel config and recompile. Then send the output of "camcontrol
inquiry da0" to scsi@freebsd.org so the quirk can be re-enabled.
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
Clarify that the implicit fallthrough was *not* intentional (thanks, Poul!)
and reorganize the code so a correct fallthrough (with /* FALLTHROUGH */)
occurs.
