usb.c: revision 1.41
revision 1.41
date: 2000/03/16 00:46:38; author: augustss; lines: +2 -2
Make the USB event queue longer. Mine overflows before the
(user-land) event handler has started. But then I have
about 25 devices connected. :)
ohci.c: revision 1.72 and 1.73
ohcivar.h: revision 1.19 and 1.20
uhci.c: revision 1.85
usbdi.h: a small part of revision 1.40
usbdivar.h: revision 1.47
Relevant commit messages from NetBSD are:
date: 2000/02/22 11:30:54; author: augustss; state: Exp;
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
----------------------------
date: 2000/02/01 05:42:53; author: augustss; state: Exp;
Put some #ifdefs around power and shutdown hooks.
some time. _All_ packets, regardless of destination, were accepted by
the machine as if addressed to it.
Jump back to 'pass' processing for a teed packet instead of falling
through as if it was ours.
PR: kern/31130
Reviewed by: -net, luigi
MFC after: 2 weeks
from 1 megabyte of ram per user to 2 megabytes of ram per user, and
reduce the cap from 512 to 384. 512 leaves around 240 MB of KVM available
while 384 leaves 270 MB of KVM available. Available KVM is important
in order to deal with zalloc and kernel malloc area growth.
Reviewed by: mckusick
MFC: either before 4.5 if re's agree, or after 4.5
usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
getpid, getuid, getgid and pipe, since they bootstrapped from
OSF/1 and never cleaned up. Switch to the native syscalls
on alpha so that the above functions work
MFC after: 7 days
extensively as none of my testboxes have speakers or an audio source at
present, but the chains built look correct and reading /dev/audio (ulaw,
translated from signed 16 bit little-endian) gives values within the
expected range for silence.
default format for the chosen subdevice cannot be obtained return an error
instead of returning success with an indeteterminate format selected.
note that this should never happen once the feederchain builder works for
recording.
which small and/or nearly full filesystems would fail with `file
system full' messages when trying to replace a number of existing
files (for example during a system installation). When the allocation
routines are about to fail with a file system full condition, they
make a call to softdep_request_cleanup() which attempts to accelerate
the flushing of pending deletion requests in an effort to free up
space. In the face of filesystem I/O requests that exceed the
available disk transfer capacity, the cleanup request could take
an unbounded amount of time. Thus, the softdep_request_cleanup()
routine will only try for tickdelay seconds (default 2 seconds)
before giving up and returning a filesystem full error. Under typical
conditions, the softdep_request_cleanup() routine is able to free
up space in under fifty milliseconds.
- Clear the cached destination before getting another cached route.
Otherwise, garbage in the padding space (which might be filled in if it was
used for IPv4) could annoy rtalloc.
Obtained from: KAME
