NULL, but also can point to dead vnode, take that into account.
PR: kern/132068
Reported by: Edward Fisk" <7ogcg7g02@sneakemail.com>, kris
Fix based on patch from: Jaakko Heinonen <jh@saunalahti.fi>
MFC after: 1 week
* Do not assume that the group lookup performed by imo_match_group()
is valid when ifp is NULL in this case.
* Instead, return EADDRNOTAVAIL if the ifp cannot be resolved for the
membership we are being asked to leave.
Caveat user:
* The way IPv4 multicast memberships are implemented in the inpcb layer
at the moment, has the side-effect that struct ip_moptions will
still hold the membership, under the old ifp, until ip_freemoptions()
is called for the parent inpcb.
* The underlying issue is: the inpcb layer does not get notification
of ifp being detached going away in a thread-safe manner.
This is non-trivial to fix.
But hey, at least the kernel should't panic when you unplug a card.
PR: 138689
Submitted by: Stef Walter
MFC after: 5 days
According to the specifications AMD/ATI SMBus controller is very
similar to SMBus controller found in PIIX4.
Some notable differences:
o different bit for enabling/signalling regular interrupt mode
o in practice seems to support only polling mode
Thus, intpm driver is modified to support polling-only mode
and to recognize SB700 PCI ID and differences.
Tested on: SB700 and PIIX4E platforms
Reviewed by: jhb
MFC after: 2 weeks
X-Perhaps-ToDo: rename the driver to reflect its function
and supported hardware
- Make xterm/cons25 support runtime configurable. This allows me to
share libteken between syscons and my new vt driver.
- Add a fix to print blanks after printing a double width character to
prevent rendering artifacts.
- Add some more utility functions that I use in the vt driver.
- Improve newer AMD processor support (Family 0Fh Revision F and later).
- Adjust offset if DiodeOffet is set and valid. Note it is experimental
but it seems to give us more realistic temperatures. Newer Linux driver
blindly adds 21C for Family 0Fh desktop processors, however.
- Always populate dev.cpu and dev.amdtemp sysctl trees regardless of probe
order for consistency. Previously, dev.cpu.N.temperature was not populated
if amdtemp was loaded later than ACPI CPU driver and temperatures were not
accessible from dev.amdtemp.N.sensor0 tree for Family 10h/11h processors.
- Read the CPUID from PCI register instead of CPUID instruction to prevent
possible revision mismatches on multi-socket system.
- Change macros and variables to make them closer to AMD documents.
- Fix style(9) nits and improve comments.
Different sub-kinds of PCI buses may have different rules and
thus it is up for the bus backends to do proper input checks.
For example, PCIe allows configuration register numbers < 0x1000,
while for PCI proper the limit is 0x100.
And, in fact, the buses already do the checks.
Reviewed by: jhb
MFC after: 1 week
X-ToDo: add check for negative value to bus backends
X-ToDo: use named constant for maximum PCIe register
"set vesa mode" and higher 16bits of the flag would be the desired mode.
One can now set, for instance, hint.sc.0.flags=0x01680180, which means
that the system should set VESA mode 0x168 upon boot.
Submitted by: paradox <ddkprog yahoo com>, swell k at gmail.com with
some minor changes.
| grep <modname>' can be used instead.
Put a message behind bootverbose as
ichwd0: <Intel ICH6M watchdog timer> on isa0
ichwd0: Intel ICH6M watchdog timer (ICH6 or equivalent)
does not make a lot of sense.
MFC after: 1 week
where we figure out the hostname length under the lock, malloc the buffer
with the lock dropped, then recheck the length under the lock and loop again
if the buffer is now too small.
Tested by: Norbert Koch nkoch demig de
MFC after: 3 days
FreeBSD 8, the compatibility shims should be built not just when FreeBSD 7
compatibility is requested, but also when compatibility with any older
FreeBSD version where that feature was present is requested.o
Without this patch, a kernel config that sets COMPAT_FREEBSD6 but not *7
would fail to build due to inconsistencies between the declaration of the
compatibility shims and their use in the SysV code.
There are similar errors in other *proto.h headers in the tree.
MFC after: 3 weeks
longs. Since 32bit processes longs are 4 bytes, 64bit kernel may copy in
or out 4 bytes more then the process expected.
Calculate the amount of bytes to copy taking into account size of fd_set
for the current process ABI.
Diagnosed and tested by: Peter Jeremy <peterjeremy acm org>
Reviewed by: jhb
MFC after: 1 week
vnodes, since these nodes are not linked into the mount queue and,
as such, the vn_lock() cannot cause a deadlock so LORs are harmless.
Suggested by: kib
Approved by: kib (mentor)
MFC after: 3 days
The hook calls vn_fullpath(9), that should not be executed with a vnode
lock held.
Reported by: Bruce Cran <bruce cran org uk>
Tested by: pho
MFC after: 3 days
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
them from the old place. This commit necessary so that the tree would not
enter a broken state.
sys/i386/isa/vesa.c -> dev/fb/vesa.c
sys/i386/include/pc/vesa.h -> dev/fb/vesa.h
sys/i386/isa/dpms.c -> dev/dpms/dpms.c
