o) Properly configure the CAM to handle IFF_PROMISC and note where IFF_ALLMULTI
handling would go if we didn't already force the NIC to receive all
multicast traffic.
Reviewed by: imp
Sponsored by: Packet Forensics
o) Inline octeon_rgmx_mark_ready into octeon_rgmx_init.
o) Add a media status handler that reports link and media status.
o) Set link state when if_init is called.
o) Remove some printfs related to driver state changes.
o) Remove some gratuitous comments.
Reviewed by: imp
Sponsored by: Packet Forensics
than spinning forever. This fixes booting with CF ejected.
NB: I've made the driver pretty chatty about errors in case there's hardware
that operates differently to mine, so we can easily track down any issues.
Reviewed by: imp
Sponsored by: Packet Forensics
redundant implementations.
o) Use ABI, not ISA, to determine address length.
o) Disable and restore interrupts around any operation that uses all 64 bits of
a register. In kernels using the O32 ABI, the upper 32 bits of those
registers is likely to be corrupted by an interrupt.
Sponsored by: Packet Forensics
- We don't need to fall back to uncacheable memory to satisfy BUS_DMA_COHERENT
requests on these CPUs.
- The bus_dmamap_sync() is a no-op for these CPUs.
A side-effect of this change is rename DMAMAP_COHERENT flag to
DMAMAP_UNCACHEABLE. This conveys the purpose of the flag more accurately.
Reviewed by: gonzo, imp
- remove unused and commented code (MIPS_BUS_SPACE_PCI, pic_usb_ack)
- use rmi_pci_bus_space for USB too (needs byteswap)
- uncomment xls_ehci.c in files.xlr
- changes to xls_ehci.c - updated with dev/usb/controller/ehci_*.c as
Obtained from: JC - c.jayachandran@gmail.com
- add bus_space_rmi_pci.c for PCI bus space
- files.xlr update for changes in files
- pcibus.c merged into xlr_pci.c (they were small files with inter-dependencies)
- xlr_pci.c - lot of changes here with few fixes, formatting cleanup
Obtained from: C. Jayachandran (JC) - c.jayachandran@gmail.com
- remove pci related code from bus_space_rmi.c, we will have another
file for PCI bus space functions which will do byte-swapping.
- remove local SWAP implementation
- added TODO stub for unimplemented functions
Obtained from: C. Jayachandran - c.jayachandran@gmail.com
- (cleanup) remove rmi specific 'struct mips_intrhand' - this is no
longer needed since 'struct intr_event' have all the required hooks
- add xlr_cpu_establish_hardintr, which has args for pre/post ithread
and filter hooks, so that the PCI code can add the PCI controller
interrupt ack code here
- make 'cpu_establish_hardintr' use the above function.
- (fix) change type of eirr/eimr from register_t to uint64_t. These
have to be 64bit otherwise we cannot handle interrupts from 32.
- (fix) use eimr to mask eirr before checking interrupts, so that we
will not handle masked interrupts.
Obtained from: C. Jayachandran - c.jayachandran@gmail.com
The backtrace code tries to look for an instruction of the form "sw ra, x(sp)"
to figure out the program counter of the calling function. When we generate
the kernel exception frame we store the 'ra' at the time of the exception
using an instruction of the same form. The problem is that the 'ra' at the
time of the exception is not the same as the 'program counter' at the time
of the exception.
The fix is to save the 'exception program counter' register by staging
it through the 'ra' register.
The RX overflow is reported in bit 2 on real hardware and Linux driver
for the same device already has this defined correctly.
This fixes frequent interrupt storms seen on RouterStation Pro boards.
Discussed with: gonzo
Getting the little-endian PCI bus working on the big-endian CPU proved to be
quite challenging. We let the PCI devices be mapped in the "match byte lanes"
address window. This is where they are mapped by the CFE and DMA transfers
generated to or from addresses within this window are not subject to automatic
byte-swapping.
However any access by the driver to memory-mapped pci space is redirected
via the "match bit lanes" address window. We get the benefit of automatic
byte swapping through this address window and drivers don't need to change
to deal with CPU big-endianness.
this in the Sibyte PCI hostbridge driver instead.
The nexus driver sees resource allocation requests for memory and irq
resources only. These are legitimate resources on all MIPS platforms.
Suggested by: imp
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
have code that detects this and makes two
transmit descriptors. However its possible
that the algorithm detects when the second
page is not used (when the data aligns perfectly
to the bottom of the page). This caused a 0
len descriptor to be added which locks up the
rge device. Skip such things with a continue.
JC provided this patch... Thanks JC :-)
Obtained from: JC (c.jayachandran@gmail.com)
Specifically on an SMP kernel it was observed that if both the
processors are doing an exit1() via ast()->postsig()->sigexit()
then we will deadlock.
This happens because exit1() calls vmspace_exit() that in turn
calls pmap_invalidate_all(). This function tries to do a
smp_rendezvous() which blocks because the other processor is not
responding to IPIs - because it too is doing AST processing with
interrupts disabled.
The platform that supports SMP currently is a SWARM with a dual-core Sibyte
processor. The kernel config file to use is SWARM_SMP.
Reviewed by: imp, rrs
disabling interrupts.
Simplify register usage - we can directly load 'curpcb' into 'k1' after
interrupts are disabled. There is no need to do so indirectly through 'a1'.
The only reason we need to have the sb_load64() and sb_store64()
functions in assembly is to cheat the compiler and generate the
'ld' and 'sd' instructions which it otherwise will not do when
compiling for a 32-bit architecture. There are some 64-bit
registers in the SCD unit that must be accessed using 64-bit
load and store instructions.
