2eaa495767
17 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
David E. O'Brien
|
aad970f1fe |
Use __FBSDID().
Also some minor style cleanups. |
||
Justin T. Gibbs
|
6c746b27b7 | Update Perforce Ids. | ||
|
Justin T. Gibbs
|
8f214efc9a |
Major update to the aic7xxx driver:
ahc_eisa.c: ahc_pci.c: Conform to new aic7xxx IRQ API. Adapt to aic7xxx_freebsd -> aic7xxx_osm changes. aic7770.c: Disable card generated interrupt early in our probe for "extra safety" Commonize some seeprom code with the PCI side of the driver. aic7xxx.c: Correctly initialize a few scratch ram locations during a sequencer restart. This avoids spurious sequencer ram parity errors in some configurations. Include the softc in ahc_update_residual calls. We need it for some diagnostics in this code path. Flag a data overrun on an auto-request sense failure as a CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR. Force a renegotiation after noticing a parity error. This covers targets that lose our negotiation settings but don't bother to give us a unit attention condition. This can happen if a target fails during a reselection of us during a cable pull. Convert some code to using constants. Fix some typos. Correct target mode message loop handling. ahc_clear_msg_state was not clearing the "need to go to message out phase" bit once our loop was over. Simplify some abort handling code. Include tag information in target mode immediate notify events. When shutting down EISA controllers, don't EISA BIOS settings in the high portions of scratch ram. This fixes warm boot issues on some systems. Save a bit of space by only allocating the SCBs that we can use. Avoid some code paths in ahc_abort_scbs() if we are currently acting as a target. Correctly cleanup stranded SCBs in the card's SCB array. These are SCBs who's mapping has already been torn down by code that aborted the SCB by seeing it in another list first. Add a comment about some potential bus reset issues for target mode on Twin (EISA only) controllers. aic7xxx.h: Cleanup the hardware scb definitions a bit. Allocate a ful 256 byte scb mapping index. This simplifies the lookup code since the table covers all possible (and potentially bogus) values. Make AHC_DEBUG work again. aic7xxx.reg: Updates to hardware SCB definition. New definitions for target mode fixes. aic7xxx.seq: In target mode, initialize SAVED_LUN just after we receive the identify message. It may be required in the error recovery path when a normal cdb packet (includes lun) is not sent up to the host for processing. Respond to irregular messages during a selection in target mode. Defer looking for space for a cdb packet until we are about to enter command phase. We want to be able to handle irregular messages even if we would otherwise return QUEUE_FULL or BUSY. Add support for sending Ignore Wide Residue messages as a target. In the disable disconnect case in target mode, set our transfer rate correctly once data are availble. aic7xxx_93cx6.c: aic7xxx_93cx6.h: Add the ability to write and erase the seeprom. aic7xxx_inline.h: Correct Big Endian handling of large cdb sizes (> 12 bytes). Adaptec to changes in the calc_residual API. Correct a target mode bug where we always attempted to service the input queue even if no progress could be made due to lack of ATIOs. aic7xxx_osm.c: Adaptec to new IRQ mapping API. The new API allows the core to only enable our IRQ mapping once it is safe (sufficient initialization) to do so. Slap bootverbose protection around some diagnostics. Only attempt DT phases if we are wide. aic7xxx_osm.h: Enable big endian support. Adjust for IRQ API change. aic7xxx_pci.c: Be more careful about relying on subvendor 9005 information. We now only trust it for HBAs. This should allow the driver to attach to some MBs where the subvendor/device information does not follow the Adaptec spec. Only enable interrupts on the card once we are fully setup. Disable external SCB ram usage on the aic7895. I have not been able to make it 100% reliable. Adjust to seeprom routines being properly prefixed with "ahc". Fix a few bugs in the external SCB ram probing routine. We need to clear any parity errors we've triggered during the probe to avoid future, fatal, interrupts. If we detect an invalid cable combination, pretent there are no cable at all. This will enable all of the terminators which is probably the safest configuration we can "guess". MFC after: 4 days |
||
|
Justin T. Gibbs
|
cd036e891a |
ahc_pci.c:
If bus_dma will give us addresses > 32 bits, setup our dma tag to accept up to 39bit addresses. aic7770.c: Update the softc directly rather than use an intermediate "probe_config" structure. aic7xxx.c: Complete core work to support 39bit addresses for bulk data dma operations. Controller data structures still must reside under the 4GB boundary to reduce code/data size in the sequencer and related data structures. This has been tested under Linux IA64 and will be tested on IA64 for FreeBSD as soon as our port can run there. Add bus dmamap synchronization calls around manipulation of all controller/kernel shared host data structures. Implement data pointer reinitialation for a second data phase in a single connection in the kernel rather than bloat the sequencer. This is an extremely rare operation (does it ever happen?) and the sequencer implementation was flawed for some of the newest chips. Don't ever allow our target role to initiate a PPR. This is forbidden by the SCSI spec. Add a few missing endian conversions in the ignore wide pointers code. The core has been tested on the PPC under Linux and should work for FreeBSD PPC. As soon as I can test the OSM layer for FreeBSD PPC, I will. Move some of ahc_softc_init() into ahc_alloc() now that the probe_config structure is gone. Add a 4GB boundary condition on all of our dma tags. 32bit DAC under PCI only works on a single 4GB "page". Although we can cross 4GB on a true 64bit bus, the card won't always be installed in one and we can save code space and cost in implementing high address support by assuming the high DWORD address will never change. Add diagnostics to ahc_search_qinfifo(). Correct a target mode issue with bus resets. To avoid an interrupt storm from a malicious third party holding the reset line, the sequencer would defer re-enabling the reset interrupt until either a select-out or select-in. Unfortunately, the select-in enable bit is cleared by a bus reset, so a second reset will render the card deaf to an initiator's attempts to contact it. We now re-enable bus reset interrupts immediately if the target role is enabled. aic7xxx.h: Remove struct ahc_probe_config. SCB's now contain a pointer to the sg_map_node so we can perfrom bus dma sync operations on the SG list prior to queuing a command. aic7xxx.reg: Register the Perforce ID for this file with the VERSION keyword so it is printed in generated files. Add the DSCOMMAND1 register which is used to access the high DWORD of address bits. Add the data pointer reinitialize sequencer interrupt code. aic7xxx.seq: Register the Perforce ID for this file with the VERSION keyword so it is printed in generated files. Remove code to re-enable the bus reset interrupt after a select-in. In target mode we cannot defer this operation as ENSELI is cleared by a bus reset. Complete 39bit support. Generate a sequencer inteerrupt rather than handle the data pointers re-initialitation in the sequencer. Inline the "seen identify" assertion to save a few cycles. Short circuit the update of our residual data if we have fully completed a transfer. The residual is correct from our last S/G load operation. Short circuit full SDPTR processing if the residual is 0. Just mark the transfer as complete. aic7xxx_93cx6.c: Synchronize perforce IDs. aic7xxx_freebsd.c: Complete untested 39bit support. Add missing endia conversions. Clear our residuals prior to starting a command. The update residual code in the core only sets the residual if there is one. aic7xxx_freebsd.h: Modeify ahc_dmamap_sync() macros to take an offset and a length. This is how sync operations are performed in NetBSD, and we should update our bus dma implementation to match. aic7xxx_inline.h: Add data structure synchronization helper functions. Fix a bug in ahc_intr() where we would not clear our unsolicited interrupt counter after running our PCI interrupt handler. This may have been the cause of the spurious PCI interrupt messages. aic7xxx_pci.c: Adjust for loss of probe_config structure. Guard against bogus 9005 subdevice information as seen on some IBM MB configurations. Add 39bit address support. MFC after: 10 days |
||
|
Justin T. Gibbs
|
58fb7d8e0b |
ahc_eisa.c:
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.
aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
aic7xxx.c:
Remove linux header ifdefs.
current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.
Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.
if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);
becomes:
ahc_update_residual(scb);
Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.
Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.
In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.
Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.
When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.
Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.
Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.
Use SCSI-3 message terminology.
aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.
current -> curr
ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.
Update some serial eeprom definitions for the latest
BIOS versions.
aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.
aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.
Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.
On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.
aic7xxx_93cx6.c:
Remove linux header ifdefs.
aic7xxx_freebsd.c:
current -> curr
Add a module event handler.
Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.
aic7xxx_freebsd.h:
Include cleanups.
Define offsetof if required.
Correct a few comments.
Update prototype of ahc_send_async().
aic7xxx_inline.h:
Implement ahc_update_residual().
aic7xxx_pci.c:
Remove linux header ifdefs.
Correct a few product strings.
Enable several U160 performance enhancing features.
Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
|
||
|
Justin T. Gibbs
|
6fb77fef4d |
This is an MFC candidate.
ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.
ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.
aic7770.c:
Sync up with core changes to support Linux EISA.
We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.
aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.
Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.
Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.
Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.
Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.
If we lookup a period of 0 in our table (async), clear the scsi offset.
aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.
Cleanup the flags definitions so that comment blocks are
not cramped.
Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.
Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.
aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.
Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.
aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.
When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.
Manage the SCB_DMA flag of SEQ_FLAGS2.
More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.
Formatting cleanup.
On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.
aic7xxx_93cx6.c:
Sync perforce ids.
aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.
Namespace cleanup.
Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.
aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.
Move ahc_power_state_change() to OSM.
aic7xxx_inline.h
Namespace cleanup.
Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.
aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.
Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.
Adjust for new 2 bit primary channel setting.
Trust the STPWLEVEL setting on v 3.X BIOSes too.
Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.
|
||
Jeroen Ruigrok van der Werven
|
7c63796828 | Preceed/preceeding are not english words. Use precede or preceding. | ||
|
Justin T. Gibbs
|
56a7c4a852 |
ahc_eisa.c:
ahc_pci.c: Add detach support. Make use of soft allocated on our behalf by newbus. For PCI devices, disable the mapping type we aren't using for extra protection from rogue code. aic7xxx_93cx6.c: aic7xxx_93cx6.h: Sync perforce IDs. aic7xxx_freebsd.c: Capture the eventhandle returned by EVENTHANDER_REGISTER so we can kill the handler off during detach. Use AHC_* constants instead of hard coded numbers in a few more places. Test PPR option state when deciding to "really" negotiate when the CAM_NEGOTIATE flag is passed in a CCB. Make use of core "ahc_pause_and_flushwork" routine in our timeout handler rather than re-inventing this code. Cleanup all of our resources (really!) in ahc_platform_free(). We should be all set to become a module now. Implement the core ahc_detach() routine shared by all of the FreeBSD front-ends. aic7xxx_freebsd.h: Softc storage for our event handler. Null implementation for the ahc_platform_flushwork() OSM callback. FreeBSD doesn't need this as XPT callbacks are safe from all contexts and are done directly in ahc_done(). aic7xxx_inline.h: Implement new lazy interrupt scheme. To avoid an extra PCI bus read, we first check our completion queues to see if any work has completed. If work is available, we assume that this is the source of the interrupt and skip reading INTSTAT. Any remaining interrupt status will be cleared by a second call to the interrupt handler should the interrupt line still be asserted. This drops the interrupt handler down to a single PCI bus read in the common case of I/O completion. This is the same overhead as in the not so distant past, but the extra sanity of perforning a PCI read after clearing the command complete interrupt and before running the completion queue to avoid missing command complete interrupts added a cycle. aic7xxx.c: During initialization, be sure to initialize all scratch ram locations before they are read to avoid parity errors. In this case, we use a new function, ahc_unbusy_tcl() to initialize the scratch ram busy target table. Replace instances of ahc_index_busy_tcl() used to unbusy a tcl without looking at the old value with ahc_unbusy_tcl(). Modify ahc_sent_msg so that it can find single byte messages. ahc_sent_msg is now used to determine if a transfer negotiation attempt resulted in a bus free. Be more careful in filtering out only the SCSI interrupts of interest in ahc_handle_scsiint. Rearrange interrupt clearing code to ensure that at least one PCI transaction occurrs after hitting CLRSINT1 and writting to CLRINT. CLRSINT1 writes take a bit to take effect, and the re-arrangement provides sufficient delay to ensure the write to CLRINT is effective. The old code might report a spurious interrupt on some "fast" chipsets. export ahc-update_target_msg_request for use by OSM code. If a target does not respond to our ATN request, clear it once we move to a non-message phase. This avoids sending a MSG_NOOP in some later message out phase. Use max lun and max target constants instead of hard-coded values. Use softc storage built into our device_t under FreeBSD. Fix a bug in ahc_free() that caused us to delete resources that were not allocated. Clean up any tstate/lstate info in ahc_free(). Clear the powerdown state in ahc_reset() so that registers can be accessed. Add a preliminary function for pausing the chip and processing any posted work. Add a preliminary suspend and resume functions. aic7xxx.h: Limit the number of supported luns to 64. We don't support information unit transfers, so this is the maximum that makes sense for these chips. Add a new flag AHC_ALL_INTERRUPTS that forces the processing of all interrupt state in a single invokation of ahc_intr(). When the flag is not set, we use the lazy interrupt handling scheme. Add data structures to store controller state while we are suspended. Use constants instead of hard coded values where appropriate. Correct some harmless "unsigned/signed" conflicts. aic7xxx.seq: Only perform the SCSIBUSL fix on ULTRA2 or newer controllers. Older controllers seem to be confused by this. In target mode, ignore PHASEMIS during data phases. This bit seems to be flakey on U160 controllers acting in target mode. aic7xxx_pci.c: Add support for the 29160C CPCI adapter. Add definitions for subvendor ID information available for devices with the "9005" vendor id. We currently use this information to determine if a multi-function device doesn't have the second channel hooked up on a board. Add rudimentary power mode code so we can put the controller into the D0 state. In the future this will be an OSM callback so that in FreeBSD we don't duplicate functionality provided by the PCI code. The powerstate code was added after I'd completed my regression tests on this code. Only capture "left over BIOS state" if the POWRDN setting is not set in HCNTRL. In target mode, don't bother sending incremental CRC data. |
||
|
Justin T. Gibbs
|
72df3c5621 |
Sync Perforce IDs, add tranceiver state change support, and correct
numerous error recovery buglets. Many thanks to Tor Egge for his assistance in diagnosing problems with the error recovery code. aic7xxx.c: Report missed bus free events using their own sequencer interrupt code to avoid confusion with other "bad phase" interrupts. Remove a delay used in debugging. This delay could only be hit in certain, very extreme, error recovery scenarios. Handle transceiver state changes correctly. You can now plug an SE device into a hot-plug LVD bus without hanging the controller. When stepping through a critical section, panic if we step more than a reasonable number of times. After a bus reset, disable bus reset interupts until we either our first attempt to (re)select another device, or another device attemps to select us. This removes the need to busy wait in kernel for the scsi reset line to fall yet still ensures we see any reset events that impact the state of either our initiator or target roles. Before this change, we had the potential of servicing a "storm" of reset interrupts if the reset line was held for a significant amount of time. Indicate the current sequencer address whenever we dump the card's state. aic7xxx.reg: Transceiver state change register definitions. Add the missed bussfree sequencer interrupt code. Re-enable the scsi reset interrupt if it has been disabled before every attempt to (re)select a device and when we have been selected as a target. When being (re)selected, check to see if the selection dissappeared just after we enabled our bus free interrupt. If the bus has gone free again, go back to the idle loop and wait for another selection. Note two locations where we should change our behavior if ATN is still raised. If ATN is raised during the presentation of a command complete or disconnect message, we should ignore the message and expect the target to put us in msgout phase. We don't currently do this as it requires some code re-arrangement so that critical sections can be properly placed around our handling of these two events. Otherwise, we cannot guarantee that the check of ATN is atomic relative to our acking of the message in byte (the kernel could assert ATN). Only set the IDENTIFY_SEEN flag after we have settled on the SCB for this transaction. The kernel looks at this flag before assuming that SCB_TAG is valid. This avoids confusion during certain types of error recovery. Add a critical section around findSCB. We cannot allow the kernel to remove an entry from the disconnected list while we are traversing it. Ditto for get_free_or_disc_scb. aic7xxx_freebsd.c: Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is set in SEQ_FLAGS. Fix a typo that caused us to execute some code for the non-SCB paging case when paging SCBs. This only occurred during error recovery. |
||
|
Justin T. Gibbs
|
c498406d58 |
Add Perforce RCSIDs for easy revision correlation to my local tree.
ahc_pci.c: Bring back the AHC_ALLOW_MEMIO option at least until the memory mapped I/O problem on the SuperMicro 370DR3 is better understood. aic7xxx.c: If we see a spurious SCSI interrupt, attempt to clear it and continue by unpausing the sequencer. Change the interface to ahc_send_async(). Some async messages need to be broadcast to all the luns of a target or all the targets of a bus. This is easier to achieve by passing explicit channel, target, and lun parameters instead of attempting to construct a device info struct to match. Filter the sync parameters for the PPR message in exactly the same way we do for an old fashioned SDTR message. Correct some typos and correct a panic message. Handle rejected PPR messages. In ahc_handle_msg_reject(), let ahc_build_transfer_msg() build any additional transfer messages instead of doing this inline. aic7xxx.h: Increase the size of both msgout_buf and msgin_buf to better accomodate PPR messages. aic7xxx_freebsd.c: Update for change in ahc_send_async() parameters. aic7xxx_freebsd.h Update for change in ahc_send_async() parameters. Honor AHC_ALLOW_MEMIO. aic7xxx_pci.c: Check the error register before going into full blown PCI interrupt handling. This avoids a few costly PCI configuration space reads when we run our PCI interrupt handler because another device sharing our interrupt line is more active than we are. Also unpause the sequencer after processing a PCI interrupt. |
||
|
Justin T. Gibbs
|
717d424718 |
Move aicasm to its own subdirectory.
Separate our platform independent hooks from core driver functionality shared between platforms (FreeBSD and Linux at this time). Add sequencer workarounds for several chip->chipset interactions. Correct external SCB corruption problem on aic7895 based cards (3940AUW). Lots of cleanups resulting from the port to another OS. |
||
|
Justin T. Gibbs
|
aa6dfd9d3d |
o Convert to <inttypes.h> style fixed sized types to facilitate porting to
other systems. o Normalize copyright text. o Clean up probe code function interfaces by passing around a single structure of common arguments instead of passing "too many" args in each function call. o Add support for the AAA-131 as a SCSI adapter. o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net o Correct manual termination support for PCI cards. The bit definitions for manual termination control in the SEEPROM were incorrect. o Add support for extracting NVRAM information from SCB 2 for BIOSen that use this mechanism to pass this data to OS drivers. o Properly set the STPWLEVEL bit in PCI config space based on the setting in an SEEPROM. o Go back to useing 32byte SCBs for all controllers. The current firmware allows us to embed 12byte cdbs on all controllers in a 32byte SCB, and larger cdbs are rarely used, so it is a better use of this space to offer more SCBs (32). o Add support for U160 transfers. o Add an idle loop executed during data transfers that prefetches S/G segments on controllers that have a secondary DMA engine (aic789X). o Improve the performance of reselections by avoiding an extra one byte DMA in the case of an SCB lookup miss for the reselecting target. We now keep a 16byte "untagged target" array on the card for dealing with untagged reselections. If the controller has external SCB ram and can support 64byte SCBs, then we use an "untagged target/lun" array to maximize concurrency. Without external SCB ram, the controller is limited to one untagged transaction per target, auto-request sense operations excluded. o Correct the setup of the STPWEN bit in SXFRCTL1. This control line is tri-stated until set to one, so set it to one and then set it to the desired value. o Add tagged queuing support to our target role implementation. o Handle the common cases of the ignore wide residue message in firmware. o Add preliminary support for 39bit addressing. o Add support for assembling on big-endian machines. Big-endian support is not complete in the driver. o Correctly remove SCBs in the waiting for selection queue when freezing a device queue. o Now that we understand more about the autoflush bug on the aic7890, only use the workaround on devices that need it. o Add a workaround for the "aic7890 hangs the system when you attempt to pause it" problem. We can now pause the aic7890 safely regardless of what instruction it is executing. |
||
|
Justin T. Gibbs
|
ba09901130 |
Update copyrights to Y2K.
93cx6.c: Make the SRAM dump output a little prettier. aic7xxx.c: Store all SG entries into our SG array in kernel space. This makes data-overrun and other error reporting more useful as we can dump all SG entries. In the past, we only stored the SG entries that the sequencer might need to access, which meant we skipped the first element that is embedded into the SCB. Add a table of chip strings and replace ugly switch statements with table lookups. Add a table with bus phase strings and message reponses to parity errors in those phases. Use the table to pretty print bus phase messages as well as collapse another switch statement. Fix a bug in target mode that could cause us to unpause the sequencer early in bus reset processing. Add the 80MHz/DT mode into our syncrate table. This rate is not yet used or enabled. Correct some comments, clean up some code... aic7xxx.h: Add U160 controller feature information. Add some more bit fields for various SEEPROM formats. aic7xxx.reg: Add U160 register and register bit definitions. aic7xxx.seq: Make phasemis state tracking more straight forward. This avoids the consumption of SINDEX which is a very useful register. For the U160 chips, you must use the 'mov' instruction to update DFCNTRL. Using 'or' to set the PRELOADED bit is completely ineffective. At the end of the command phase, wair for our ACK signal to de-assert before disabling the SCSI dma engine. For slow devices, this avoids clearing the ACK before the other end has had a chance to see it and lower REQ. |
||
Peter Wemm
|
c3aac50f28 | $Id$ -> $FreeBSD$ | ||
|
Justin T. Gibbs
|
b53bae294f | Turn the 'dump eeprom' flag into a real option. | ||
|
Justin T. Gibbs
|
5a151d297c |
Correct an invalid (and unused) #define in 93cx6.c
Freeze the transaction queue for any type of scsi status other than "okay". |
||
|
Justin T. Gibbs
|
3bafc9d432 |
Massive overhaul of the aic7xxx driver:
- Convert to CAM - Use a new DMA based queuing and paging scheme - Add preliminary target mode support - Add support for the aic789X chips - Take advantage of external SRAM on more controllers. - Numerous bug fixes and performance improvements. |