- Increasing queue depth gives ~100% performance improvement for
randwrite fio test in Azure.
- New channel selection, which takes LUN id and the current cpuid
into consideration, gives additional ~20% performance improvement
for ranwrite fio test in Azure.
Submitted by: Hongzhang Jiang <honzhan microsoft com>
Modified by: sephe
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7622
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
indicate (potentially partial) success of the open. Use these to
decide what to close in sccnclose(). Only grab/ungrab use open/close
so far.
Add a per-sc variable to count successful keyboard opens and use
this instead of the grab count to decide if the keyboad state has
been switched.
Start fixing the locking by using atomic ops for the most important
counter -- the grab level one. Other racy counting will eventually
be fixed by normal mutex or kdb locking in most cases.
Use a 2-entry per-sc stack of states for grabbing. 2 is just enough
to debug grabbing, e.g., for gets(). gets() grabs once and might not
be able to do a full (or any) state switch. ddb grabs again and has
a better chance of doing a full state switch and needs a place to
stack the previous state. For more than 3 levels, grabbing just
changes the count. Console drivers should try to switch on every i/o
in case lower levels of nesting failed to switch but the current level
succeeds, but then the switch (back) must be completed on every i/o
and this flaps the state unless the switch is null. The main point
of grabbing is to make it null quite often. Syscons grabbing also
does a carefully chosen screen focus that is not done on every i/o.
Add a large comment about grabbing.
Restore some small lost comments.
- in sccnopen(), open the keyboard before the screen. The keyboard
currently requires Giant (although it must be spinlocked to work
correctly as a console), so the previous order would be a LOR if
it has any semblance of locking.
- add a (currently dummy) state arg to scgetc().
As the support for large blocks was enabled in loader zfs code, the
heap in userboot was left not changed, resulting with failure of detecting
and accessing zfs pools for bhyve virtual machines.
This fix does set the heap to use same amount of memory as the zfsloader
is using. To make it possible to test and verify loader functions, bhyve
is providing very useful option, but it also means, we like to keep feature
parity with [zfs]loader as close as possible.
PR: 212038
Reported by: dfh0522@gmail.com
Reviewed by: allanjude, grehan
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D7635
The issue was introduced with adding support for salted checksums, and
was revealed by bhyve userboot.so.
During pool discovery the loader is reading pool label from disks, and
at that time the spa structure is not yet set up, so the NULL pointer
is passed for spa. This condition must be checked to avoid the corruption
of the memory and NULL pointer dereference.
PR: 212114
Reported by: tsoome@freebsd.com
Reviewed by: allanjude
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D7634
needed before enabling superpages on arm64. This code is based on the amd64
pmap with changes as needed to handle the differences between the two
architectures.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
iterate over superpages. We don't yet create these, but soon will.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Where the cloudabi64 kernel can be used to execute 64-bit CloudABI
binaries, this one should be used for 32-bit binaries. Right now it
works on i386 and amd64.
A nice thing about requiring a vDSO is that it makes it incredibly easy
to provide full support for running 32-bit processes on 64-bit systems.
Instead of letting the kernel be responsible for composing/decomposing
64-bit arguments across multiple registers/stack slots, all of this can
now be done in the vDSO. This means that there is no need to provide
duplicate copies of certain system calls, like the sys_lseek() and
freebsd32_lseek() we have for COMPAT_FREEBSD32.
This change imports a new vDSO from the CloudABI repository that has
automatically generated code in it that copies system call arguments
into a buffer, padding them to eight bytes and zero-extending any
pointers/size_t arguments. After returning from the kernel, it does the
inverse: extracting return values, in the process truncating
pointers/size_t values to 32 bits.
Obtained from: https://github.com/NuxiNL/cloudabi
The native CloudABI data types header file used to be pulled in by the
vDSOs when they were still written in C. Since they are now all
rewritten in assembly, this can go away.
In all of these source files, the userspace pointer size corresponds
with the kernelspace pointer size, meaning that casting directly works.
As I'm planning on making 32-bit execution on 64-bit systems work as
well, use TO_PTR() here as well, so that the changes between source
files remain minimal.
Use sbintime_t timeouts with precision control to get very accurate
timing. It costs little to always ask for about 1% accuracy, and the
not so new event timer implementation usual delivers that, and when
it can't it gets much closer than our previous coarse timeouts and
buggy simple countdown.
The 2 fastest atkbd repeat rates have periods 34 and 38 msec, and ukbd
pretended to support rates in between these. This requires
sub-microsecond precision and accuracy even to handle the 4 msec
difference very well, but ukbd asked the timeout subsystem for timeouts
of 25 msec and the buggy simple countdown of this gave a a wide range
of precisions and accuracies depending on HZ and other timer
configuration (sometimes better than 25 msec but usually more like 50
msec). We now ask for and usually get precision and accuracy of about
1% for each repeat and much better on average.
The 1% accuracy is overkill. Rounding of 30 cps to 34 msec instead of
33 already gives an error of +2% instead of -1%, and ut AT keyboards on
PS/2 interfaces have similar errors.
A timeout is now scheduled for every keypress and release. This allows
some simplifications that are not done. It allows removing the timeout
scheduling for exiting polled mode where it was unsafe in ddb mode. This
is done. Exiting polled mode had some problems with extra repeats. Now
exiting polled mode lets an extra timeout fire and the state is fudged
so that the timeout handler does very little.
The sc->time_ms variable is unsigned to avoid overflow. Differences of
it need to be signed. Signed comparisons were emulated by testing an
emulated sign bits. This only works easily for '<' comparisonss, but
we now need a '<=' comparison. Change the difference variable to
signed and use a signed comparison. Using unsigned types here didn't
prevent overflow bugs but just reduced them. Overflow occurs with
n repeats at the silly repeat period of [U]INT_MAX / n. The old countdown
had an off by 1 error, and the simplifications would simply count down
1 to 0 and not need to accumulate possibly-large repeat repeats.
And stringent input IC version negotiate message checks.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7614
RESET is not used by the hn(4) at all, and RESET_CMPLT does not even
have a rid to match with the pending requests. So, let's put it
onto an independent switch branch and log a warning about it.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7602
Summary:
Kernel maps only one page of FDT. When FDT is more than one page in size, data
TLB miss occurs on memmove() when FDT is moved to kernel storage
(sys/powerpc/booke/booke_machdep.c, booke_init())
This introduces a pmap_early_io_unmap() to complement pmap_early_io_map(), which
can be used for any early I/O mapping, but currently is only used when mapping
the fdt.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7605
While I'm here, sort the RNDIS status in ascending order.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7594
The thermal sensor lives in the touch screen controller. Touch screen part
isn't done for now.
Temperature is read every ~2 seconds and exposed via sysctl.
kbdcontrol -r fast is documented to give a non-emulated atkbd's fastest
rate of 250.34, but is misimplemented to request this as 0.0. ukbd
supports many nonstandard rates, although it is currently too inaccurate
by a factor of several hundred for non-huge nonstandard rates to be
useful. It mapped 0.0 to 200.0. A repeat delay of 0 means a rate of
infinity which is quite fast, but physical constraints limit this to
a few MHz and the inaccuracies made it almost usable.
Convert 0.0 to the documented 250.34.
Also convert negative args and small args to the 250.34 minimal ones,
like atkbd does. This is for KDSETREPEAT -- the 2 versions of the
deprecated KDSETRAD have bounds checking. Keep not doing any bounds
checking or conversions for upper limits since nonstandard large
delays are useful for testing.
The inaccuracies are dependent on HZ and the timeout implementation.
With the old timeout implementation and HZ = 1000, 200.0 probably
worked better to emulate 250.34 than 250.34 itself. HZ = 100 gives
roundoff errors that accidentally reduce the inaaccuracies, and
event timers reduce the inaccuracies even more, so 200.0 was giving
more like itself (perhaps 215.15 on average but sometimes close to
10 msec repeat which is noticebly too fast). This commit makes 0.0
noticeably too slow, like 250.34 always was.
An optimization is in place to skip reading the .depend.* files with
'make install'. This was too strong and broke 'make all install' and
'make foo.o foo install'. Now only skip reading the dependency files
if all make targets ran are install targets.
The problem comes about because headers are only added in as a guessed
dependency if .depend.* files do not yet exist. If they do exist, even
if being skipped from being read, then the header dependencies are not
applied. This applies to all #included files, and not just headers.
Reported by: kib
MFC after: 1 day
Sponsored by: EMC / Isilon Storage Division
handling. This resulted in the window target being left uninitialized
when an underflow occured.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7617
finding the vm_page_t in pmap_extract_and_hold. Previously it would return
the vm_page_t of the first page in a block. This would cause issues when,
for example, fsck reads from a device into the middle of a superpage. In
this case the read call would write to the start of the block, and not to
the buffer passed in.
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Allow netbooting on efi without having to setup any NFS server by rebuilding the
loader with LOADER_TFTP_SUPPORT like for the i386 pxeloader
Sponsored by: Gandi.net
This code should be able to support later AMD chipsets as well, but that
hasn't been tested.
SB800 supports accessing several different SMBus buses using the same
set of constrol registeirs plus special PMIO registers that control which
bus is selected. This could be exposed to consumers as several smb devices
each talking to its bus. This feature is not implemented yet.
MFC after: 2 weeks
Summary:
There is no need to call tlb1_init() twice. Now it is called first time from
booke_init() and second time from powerpc_init() (where it is under BOOKE
switch). Although this does not cause immediate problems in the mainline kernel,
this can lead to undesirable side effects like two TLB entries with the same VA
in the TLB1. Presence of two TLB entries with the same VA can hang CPU.
Test Plan:
Add initial mapping for UART to the tlb1_init(), build and boot the kernel,
ensure that mapping presents only once (most convinient way - through Lauterbah
or similar hardware debugger)
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7607
Summary: Current booke/pmap code ignores mas7 and mas8 on e6500 CPU.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7606
