This is a subtle use-after-free race that results in some very undesirable
hang behaviour.
Reviewed by: pkelsey
Obtained from: Kip Macy, NextBSD (91a9bd1dbb)
Gleaned from a public header file. 5402 and 5404 look like they may be
used on embedded devices. 5478 and 5488 are switch PHYs. 5754 change is just
to note a product alias.
Differential Revision: https://reviews.freebsd.org/D3338
Submitted by: kevin.bowling@kev009.com
delete a logic volume on status change which is NOT what we want here.
The original code is correct in that when the volume changes status
the driver will only delete the volume if the status is one of the
fatal errors. A drive failure in a mirrored volume is NOT a situtation
where the volume should dissapear.
Reported on freebsd-scsi@:
https://lists.freebsd.org/pipermail/freebsd-scsi/2015-September/006800.html
MFC after: 3 days
Resetting some generations of the I/OAT hardware (just BDXDE for now)
resets the corresponding MSI-X registers. So, teardown and
re-initialize interrupts after resetting the hardware.
Reviewed by: jimharris
Approved by: markj (mentor)
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3549
SoC is used in the HiKey board from 96boards.
Currently on the SD card is working on the HiKey, as such devices 0 and 2
will need to be disabled, for example by adding the following to
loader.conf:
hint.hisi_dwmmc.0.disabled=1
hint.hisi_dwmmc.2.disabled=1
Relnotes: yes (Hikey board booting)
Sponsored by: ABT Systems Ltd
in Marvell terms) to 32768. 32768 looks overkill but it will
ensure correct DMAed update. This change addresses occasional
watchdog timeouts reported on 10.2-RELEASE.
Tested by: Johann Hugo <jhugo@meraka.csir.co.za>
MFC after: 2 weeks
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
While here update the list of devices id to match the one in linux 3.8.13
Reviewed by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3489
Keep a couple of old macros that will be removed lated when the rest of the code
will be updated to 3.8.13 equivalent.
Chase the renamed macros
Reviewed by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3487
