The code doesn't compile (I'll do that in a minute), but functionally
it gets to receveing the interrupt from the start or join net command.
There is a lot of code to deal with the limitations of the PCCard memory
mapping code - I'm changing some of it hence the check in to preserve something
that worked.
Call intr_teardown on detach.
Always add non masterdevice from unit 2 upwards.
Update to the pccard code, at least some cards are now working,
more testing to follow.
from useful drivers such as the 3D DRI drivers I will be porting for
hardware accelerated OpenGL. The hardware will still be reported during
boot using the nomatch system.
Approved by: jkh
was needed to make attach/detach of devices work, which is
needed for the PCCARD support.
(PCCARD support is still not working though, more to come on that)
Support the CMD646 chip which is used on many alphas, sadly only
in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes.
Lots of cosmetic fixes here and there.
Sorry for the size of this megapatchfromhell but it was not
possible otherwise...
newbus patches based on work from: dfr (Doug Rabson)
accept a new command; in high load cases it may be too busy for the old
value.
This loop needs something to tie it to real time, rather than just the CPU's
ability to fetch from the L1 data cache, but this hack works for now.
Approved by: jkh
1) Non-AST4 multiport cards were broken by bypassing the code that changes
`idev' to the multiport master device.
2) AST4 multiport cards apparently were broken by inverting the test for
the master device having an irq.
3) Error handling for nonexistent master devices was broken by removing a
check for a null pointer.
4) `int' error codes returned by bus_get_resource() were assigned directly
to the boolean variable com->no_irq. Probably harmless, since the
boolean is implemented as a u_char.
Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com>
part 2) by yokota
Approved by: jkh
Andrew's problems with SCSI on some alphas- do not call isp_update
directly to update parameters- just mark them as being ready to
update for the next command- the system would just hang on a READ
CAPACITY for a drive. Really annoying because it wouldn't even timeout
(and it has a timeout) so either the SET PARAMETERS call was nuking
things or the f/w was really dropping the ball.
approved: jkh
Reviewed by: gallatin@freebsd.org
is gone as a define. We just don't support fast posting for anything less
than the 1240/1080/1280/12160 or Fibre Channel cards.
Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44
bytes are allowed).
Approved: jkh
- Remove all the code intended to deal with experimental
C1010 revisions. This code got useless due to commercial
chip revisions having been fixed.
Fixes:
- Rewrite/rework the WSR condition handling.
Previous drivers snooped on the BUS through the SBDL IO
register and this has been discovered to trigger a spurious
SCSI parity error when WSR had been set by chip and cleared
by SCRIPTS prior to reading SBDL bit [0...7].
On the other hand, the C1010 does not use the SWIDE register
when synchronous data transfers are taking place and
requires a CHMOV (1) WHEN DATA_IN to be performed in order
to move to memory the residual byte when WSR is set and
the residual byte is useful data.
BTW, the new WSR handling by the driver is simpler.
- No longer attempt to read from SCRIPTS the SBDL register.
This is intended to avoid to be victimized again by any other
issue regarding the handling of this register by 8xx chips.
Miscellaneous:
- The driver is now able to handle the WSR + IGN RESIDUE
condition at the end of a DATA IN I/O without need of a
programmed interrupt. It is a minor? optimization.
- A few other minor cosmetic changes.
This driver version fixes notably a permanent SCSI parity
error condition at boot that can be triggerred due to recent
changes in cam_xpt.c between 1.79 and 1.80.
Changes in CAM/XPT are fine, but the new handling of the full
INQUIRY may trigger the driver problem when a target returned
an odd value in the `additionnal length' field of the INQUIRY
response.
The diff against previous driver version is large, but it
consists approximatively in:
- 350 lignes removed and not compiled in previous drivers
(They addressed experimental C1010 revisions)
- 250 lignes added or changed, half being comments or empty
lines.
So, in fact, the real changes are about 120 lines of source.
About 80 lines address SCRIPTS changes and about 40 lines
address C code changes.
Approved by: jkh
New WSR handling reviewed by Pamela Delaney <pam.delaney@lsil.com>
(For back-porting to Linux sym53c8xx driver 1.6x series)
for 1020/1X80/12160/2X00- for readability. Add in 12160 (Ultra3)
support- but not with PPR just yet. Fix and clarify fetching of
return parameter for getting firmware rev which for the 2200 contains
the connection topology (Private Loop (NL-port), N-port, FL-port,
F-port). Synthesize the connection topology for the 2100 which can
only be Private Loop or FL-port. Handle a couple of new async
mailbox commands which signify connection in Point-to-Point mode
(N-port or F-port) or indicate various toe stubbing getting to same.
Approved: jkh@freebsd.org
won't appear on the screen, and "blinking" and "destructive" cursor
won't appear in the vty for which the text cursor is currently hidden.
Approved by: jkh
problem was basically (for offset > 4096):
vtophys(addr) + offset != vtophys(addr + offset)
Also, use TD's with a maximum size of 4k instead of 8kb for OHCI
controllers.
This problem occurs in drivers that use large transfer sizes:
umass, host2host and ethernet with jumbo frames.
for optimizing the unpause operation no-longer exist, and this is much
safer.
When restarting the sequencer, reconstitute the free SCB list on the card.
This deals with a single instruction gap between marking the SCB as free
and actually getting it onto the free list.
Reduce the number of transfer negotiations that occur. In the past, we
renegotiated after every reported check condition status. This ensures
that we catch devices that have unexpectidly reset. In this situation,
the target will always report the check condition before performing a
data-phase. The new behavior is to renegotiate for any check-condition where
the residual matches the orginal data-length of the command (including
0 length transffers). This avoids renegotiations during things like
variable tape block reads, where the check condition is reported only
to indicate the residual of the read.
Revamp the parity error detection logic. We now properly report and
handle injected parity errors in all phases. The old code used to hang
on message-in parity errors.
Correct the reporting of selection timeout errors to the XPT. When
a selection timeout occurs, only the currently selecting command
is flagged with SELTO status instead of aborting all currently active
commands to that target.
Fix flipped arguments in ahc_match_scb and in some of the callers of this
routine. I wish that gcc allowed you to request warnings for enums passed
as ints.
Make ahc_find_msg generically handle all message types.
Work around the target mode data-in wideodd bug in all non-U2 chips.
We can now do sync-wide target mode transfers in target mode across the
hole product line.
Use lastphase exclusively for handling timeouts. The current phase
doesn't take the bus free state into account.
Fix a bug in the timeout handler that could cause corruption of the
disconnected list.
When sending an embedded cdb to a target, ensure that we start on a
quad word boundary in the data-fifo. It seems that unaligned stores
do not work correctly.
is initialised by usb_init.
This might solve problems with some controllers not being initiliased
properly, because a delay was effectively a tsleep that returned
immediately.
Approved by: jhk
the PIRQD bit.
This fixes the problem of uhub0 hanging forever during boot when USB
keyboard support is switched on in the BIOS on motherboards with Intel
chipsets (UHCI).
Approved by: The Sheep
fix support for multiple HPT & Promise controllers.
support mixed 33/66 devices on the Promise 66 controllers.
fix the refcount stuff in the atapi drivers.
misc cleanups.
support is also included for the ASC38C1600 Ultra160 chipset, but
as firmware is not yet available for this chip, it is disabled.
Approved by: jkh@FreeBSD.org
Also update wicontrol to enable/disable encryption, set WEP keys and set the
TX key index. Silver cards only have 40-bit keys. This is something of a quick
hack, but it works well enough for me to commit this from the LinuxWorld
exhibit floor.
The WEP support only shows up if you have a card that supports it.
Would have been approved by: jkh, if he hadn't wandered off somewhere
Approved in his place by: msmith, who's standing right here
bus_delete_resource.
Fixes a problem when the probe succeeded, but the attach failed. The
release of the resources was done inproperly.
Approved by: jkh
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
Some controllers submit bogus pointers to the Done queue.
ohci_hash_find_td fails to find these in its hash and panics. Instead of
panicing we now assume the whole done queue is lost and let the timeout
code to clean up the mess after us.
condition.
- 1 line change that allows to balance chips between ncr
and sym using pci compat option (not compiled by default
in 4.0 but maintains the driver source 3.4 compatible).
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
Try to support older systems reporting irq0 for the first channels.
Support sharing of the std interrupts (says peter :) )
Dont use READ_CD on normal data reads (2048 bytes), too many old drives
doesn't support this command even if the std says "shall" :(, but still
use READ_CD on all other blocksizes.
Add the geometry to the ad probe, its still usefull.
does ignore DCD. Even TIOCMGET cannot read DCD as the firmware doesn't
report it. This has pretty interesting effects for ppp(8) which runs
in clocal mode and polls carrier (!). (Specialix's linux driver does
this too)
Also update the firmware to 3.0.6 for the SX cards, as apparently there
was a problem with floating (disconnected) DCD pins causing stray carrier
transitions, especially at port open time.
It seems to work here, and carrier loss is detected nearly immediately
rather than having to wait for a LQR timeout (a few minutes) before ppp(8)
gives up.
DCD problem noted by: nsayer
Dont be so verbose in the probe, only ONE line printed now, to get more
info boot verbose. Centralise most printf's in ata-all & ata-dma to use
the ata_printf function, it saves alot of codelines.
Repeat the identify command if drive fails the first.
Protect the timeout functions with splbio.
Dont update the transfer details before we are sure the transfer
succeded, this way they are proberly retried on errors.
Move the handling of next_writeable to userland.
Use the READ_CD command to read CD's. That enables us to read _anything_
via the normal read/write interface. This kindof obsoletes the READAUDIO
ioctl, but we keep that for now.
Update i2c code to build on FreeBSD 3.x and 4.x machines.
Added GPIO audio values for the Askey/Dynalink TV card talken from postings on the V4L mailing list.
Update Australian Channel Set. Submitted by John Birrell <jb@cimlogic.com.au>
Add new Channel Set for France. Submitted by Daniel Dagneaux <dagneaux@lure.u-psud.fr>
doesn't conflict with the parallel port on my miata (0x3bc..0x3bf).
The right solution will be to reserve two port ranges in vga, 0x3b0..0x3ba
and 0x3c0..0x3ca.
Reviewed by: yokota
o Cut out the probed stuff. We no longer need it since newbus implicitly
checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload. Untested because aha doesn't yet
support identify and there are some interactions with PnP that I've
not yet worked out.
With this I can boot the AHA-1542CP FW F.0. All the aha resources
appear to be picked up via pnp now.
The files were repo copied from their original location and are part
way towards being portable.
This should unbreak the EISA support in the driver.
I have not updated files* yet as I'm not quite finished.
the resource table to locate children. The 'at ppbus?' can go again.
Remove a few #if Nxxx > 0' type things, config arranges this for us.
Move the newbus method glue next to the DRIVER_MODULE() stuff so we
don't need extra prototypes.
Don't set device descriptions until after the possibility of the probe
returning an error.
Remove all cdevsw_add() calls, all the drivers that did this also use
make_dev() correctly, so it's not required.
A couple of other minor nits.
isa_device->id_ri_flags and RI_FAST were not implemented and did nothing.
The two drivers that were mistakenly thinking this was working were
cy.c and loran.c - these should be converted to newbus.
GC (garbage collect) isa_device->id_alive
GC userconfig.c references to isa_device->id_scsiid (!).
Fix a long-standing bug where I used a 'break;' instead of a 'continue;';
you had to have multiple ISA boards in non-PnP mode with an 'unknown' board
with a lower MAC address to find this one. Since I have 4 3c5x9 boards
in my test box I was somewhat confused when this happened. :)
Make the messages printed by ep_isa_identify() a little more consistent;
we'll only see them in verbose boot mode but it makes me feel better if
they look nice.
Also, while I'm here, add a mechanism to catch unknown board IDs that
are likely to be 3c509s and allow them to be attached.
PR: kern/16304
Submitted by: Kelly Yancey <kbyanc@posi.net>
