struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
- Let hme_start()/hme_init() acquire lock and then call
hme_start_locked()/hme_init_locked() respectivly.
- Teardown interrupt handler before hme_detach().
- Remove IFF_NEEDSGIANT flag and mark interrupt handler INTR_MPSAFE.
- Set callout handler to CALLOUT_MPSAFE.
- Add locks in hme MII interface.
Reviewed by: jake
Tested by: Julian C. Dunn <jdunn at opentrend dot net>
MFC after: 2 weeks
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
Since HME doesn't compensate the checksum for UDP datagram which
can yield to 0x0, UDP transmit checksum offload is disabled by
default. The UDP Transmit checksum offload can be reactivated
by setting special link option link0 with ifconfig(8).
Approved by: jake (mentor)
Reviewed by: tmm
Tested by: Herve Boulouis <amon@sockar.homeip.net>
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
- remove some useless code from the status change handler that was intended
to enable the the MII drivers for external phys; this is already done
during interface initialization, and the deleted code made some
assumptions about phy addresses that do not seem to hold true on newer
cards. This should get at least one of the two hmes of newer Netra t1
machines working.
- correct the interrupt resource allocation
- bump the number of RX descriptors, lower values cause promblems on some
machines
in most machines of the Sun Ultra series. This is a port of the NetBSD
driver which I enhanced to make use of the gather functionality and the
configurable RX buffer offset to avoid copying all received/sent packet
(instead, packets will be directly DMAd from mbuf chains and into mbuf
clusters now).
