Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
Because the code lacks all the GNU extensions to printf() format stuff,
the compiler doesn't helpfully tell us that I messed up in a previous
commit.
Pointy hat to: adrian, who likely only cares about this because he's the
only one who bothers flipping on net80211 debugging.
uses of the page queues mutex with a new rwlock that protects the page
table and the PV lists. This reduces system time during a parallel
buildworld by 35%.
Reviewed by: alc
within the BAW.
This regression was introduced in ane earlier commit by me to fix the
BAW seqno allocation-but-not-insertion-into-BAW race. Since it was only
ever using the to-be allocated sequence number, any frame retries
with the first frame in the BAW still in the software queue would
have constantly failed, as ni_txseqs[tid] would always be outside
the BAW.
TODO:
* Extract out the mostly common code here in the agg and non-agg ADDBA
case and stuff it into a single function.
PR: kern/166357
Function acquired reader lock if needed.
Assert check for reader or writer lock (RA_LOCKED / RA_UNLOCKED)
- While here, add knlist_init_mtx.9 to MLINKS and fix some style(9) issues
Reviewed by: glebius
Approved by: ae(mentor)
MFC after: 2 weeks
I see traffic stalls.
It turns out that the bug isn't because the first and last frame in the
BAW is in the software queue. It is more likely that it's because
the first frame in the BAW is still in the software queue and thus there's
no more room to allocate and do subsequent TX.
PR: kern/166357
net.inet.ip.fw.tables_max is now read-write.
- Bump IPFW_TABLES_MAX to 65535
Default number of tables is still 128
- Remove IPFW_TABLES_MAX from ipfw(8) code.
Sponsored by Yandex LLC
Approved by: kib(mentor)
MFC after: 2 weeks
XenServer configurations that advertise the multi-page ring extension,
but only allow a single page of ring space.
sys/dev/xen/blkfront/blkfront.c:
If only one page of ring space is being used, do not publish
in the XenStore the number of pages in use (1), via either
of the supported multi-page ring extension schemes.
Single page operation is the same with or without the
ring-page extension being negotiated. Relying on the
legacy behavior avoids an incompatible difference in how
the two ring-page extension schemes that are out in the
wild, deal with the base case of a single page. The
Amazon/Red Hat drivers use the same XenStore variable as
if the extension was not negotiated. The Citrix drivers
assume the new ring reference XenStore variables will be
available
Reported by: Oliver Schonefeld <schonefeld@ids-mannheim.de>
MFC after: 3 days
This is not entirely correct as it simply resets the channel, flushing
whatever is in the TX/RX queue. This can and will break aggregation
BAW tracking. But the alternative (HT40 frames being sent with the hardware
in HT20 mode) is even worse.
There's still a small window between the htinfo being received (and the ni_chw
field being updated) which could cause problems. I'll look at fleshing this
out in follow-up commits.
PR: kern/166286
Currently, a channel width change updates the 802.11n HT info data in
net80211 but it doesn't trigger any device changes. So the device
driver may decide that HT40 frames can be transmitted but the last
device channel set only had HT20 set.
Now, a task is scheduled so a hardware reset or change isn't done
during any active ongoing RX. It also means that it's serialised
with the other task operations (eg channel change.)
This isn't the final incantation of this work, see below.
For now, any unmodified drivers will simply receive a channel
change log entry. A subsequent patch to ath(4) will introduce
some basic channel change handling (by resetting the NIC.)
Other NICs may need to update their rate control information.
TODO:
* There's still a small window at the present moment where the
channel width has been updated but the task hasn't been fired.
The final version of this should likely pass in a channel width
field to the driver and let the driver atomically do whatever
it needs to before changing the channel.
PR: kern/166286
<20120222095239.Horde.0hpYHJjmRSRPRKzXsoFRbYk@webmail.leidinger.net>.
According to some private emails received, it apparently is not unpopular
to use at least Quad GigaSwift cards driven by cas(4) in x86 machines.
MFC after: 1 week
order to avoid otherwise harmless witness warnings when these are acquired
at the same time and due to both using MTX_NETWORK_LOCK as their type.
The right fix actually would be to use different, descriptive types for
these. However, the latter would require undesirable changes to the shared
code base. Another approach would be to just supply NULL as the type, which
was deemed as less desirable though as it would cause the unique but cryptic
name also to be used for the type and to diverge from the type used by other
network device drivers.
MFC after: 1 week
DMA tag with a 4 GB boundary as required by PCI-Express. With r232403 in
place this actually is redundant. However, the host-PCI-Express bridge
driver is the more appropriate place for implementing this restriction.
MFC after: 3 days
recent changes in sys/x86/include/endian.h:
sys/dev/dcons/dcons.c:190:15: error: implicit conversion from '__uint32_t' (aka 'unsigned int') to '__uint16_t' (aka 'unsigned short') changes value from 1684238190 to 28526 [-Werror,-Wconstant-conversion]
buf->magic = ntohl(DCONS_MAGIC);
^~~~~~~~~~~~~~~~~~
sys/sys/param.h:306:18: note: expanded from:
#define ntohl(x) __ntohl(x)
^
./x86/endian.h:128:20: note: expanded from:
#define __ntohl(x) __bswap32(x)
^
./x86/endian.h:78:20: note: expanded from:
__bswap32_gen((__uint32_t)(x)) : __bswap32_var(x))
^
./x86/endian.h:68:26: note: expanded from:
(((__uint32_t)__bswap16(x) << 16) | __bswap16((x) >> 16))
^
./x86/endian.h:75:53: note: expanded from:
__bswap16_gen((__uint16_t)(x)) : __bswap16_var(x)))
~~~~~~~~~~~~~ ^
This is because the __bswapXX_gen() macros (for x86) call the regular
__bswapXX() macros. Since the __bswapXX_gen() variants are only called
when their arguments are constant, there is no need to do that constancy
check recursively. Also, it causes the above error with clang.
Fix it by calling __bswap16_gen() from __bswap32_gen(), and similarly,
__bswap32_gen() from __bswap64_gen().
While here, add extra parentheses around the __bswap16_gen() macro
expansion, to prevent unexpected side effects.
- header and stub .c file for fasttrap module. It's not supported on
MIPS yet, but there is no way to disable support completely
- Do as amd64 trying to limit allocated memory
Note that this driver additionally probes some device IDs for the most
part not know to other MPT drivers, if at all. So rename the macros not
present in mpi_cnfg.h to match the naming scheme in the latter and but
suffix them with a _FB in order to not cause conflicts.
- Like mpt_set_config_regs(), comment out mpt_read_config_regs() as the
content of the registers read isn't actually used and both functions
aren't exactly up to date regarding the possible layouts of the BARs
(these function might be helpful for debugging though, so don't remove
them completely).
- Use DEVMETHOD_END.
- Use NULL rather than 0 for pointers.
- Remove an unusual check for the softc being NULL.
- Remove redundant zeroing of the softc.
- Remove an overly banal and actually partly incorrect as well as partly
outdated comment regarding the allocation of the memory resource.
MFC after: 3 days
