In case when decrypted and decapsulated packet is an UDP datagram,
check that its checksum is not zero before doing incremental checksum
adjustment.
Reported by: Eugene Grosbein
Tested by: Eugene Grosbein
Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Reviewed by: gnn, wblock
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
This function is used only by ipsec_getpolicybysock() to fill security
policy index selector for locally generated packets (that have INPCB).
The function incorrectly assumes that spidx is the same for both directions.
Fix this by using new direction argument to specify correct INPCB security
policy - sp_in or sp_out. There is no need to fill both policy indeces,
because they are overwritten for each packet.
This fixes security policy matching for outbound packets when user has
specified TCP/UDP ports in the security policy upperspec.
PR: 213869
MFC after: 1 week
Since the previous algorithm, based on bit shifting, does not scale
with large replay windows, the algorithm used here is based on
RFC 6479: IPsec Anti-Replay Algorithm without Bit Shifting.
The replay window will be fast to be updated, but will cost as many bits
in RAM as its size.
The previous implementation did not provide a lock on the replay window,
which may lead to replay issues.
Reviewed by: ae
Obtained from: emeric.poupon@stormshield.eu
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D8468
than removing the network interfaces first. This change is rather larger
and convoluted as the ordering requirements cannot be separated.
Move the pfil(9) framework to SI_SUB_PROTO_PFIL, move Firewalls and
related modules to their own SI_SUB_PROTO_FIREWALL.
Move initialization of "physical" interfaces to SI_SUB_DRIVERS,
move virtual (cloned) interfaces to SI_SUB_PSEUDO.
Move Multicast to SI_SUB_PROTO_MC.
Re-work parts of multicast initialisation and teardown, not taking the
huge amount of memory into account if used as a module yet.
For interface teardown we try to do as many of them as we can on
SI_SUB_INIT_IF, but for some this makes no sense, e.g., when tunnelling
over a higher layer protocol such as IP. In that case the interface
has to go along (or before) the higher layer protocol is shutdown.
Kernel hhooks need to go last on teardown as they may be used at various
higher layers and we cannot remove them before we cleaned up the higher
layers.
For interface teardown there are multiple paths:
(a) a cloned interface is destroyed (inside a VIMAGE or in the base system),
(b) any interface is moved from a virtual network stack to a different
network stack ("vmove"), or (c) a virtual network stack is being shut down.
All code paths go through if_detach_internal() where we, depending on the
vmove flag or the vnet state, make a decision on how much to shut down;
in case we are destroying a VNET the individual protocol layers will
cleanup their own parts thus we cannot do so again for each interface as
we end up with, e.g., double-frees, destroying locks twice or acquiring
already destroyed locks.
When calling into protocol cleanups we equally have to tell them
whether they need to detach upper layer protocols ("ulp") or not
(e.g., in6_ifdetach()).
Provide or enahnce helper functions to do proper cleanup at a protocol
rather than at an interface level.
Approved by: re (hrs)
Obtained from: projects/vnet
Reviewed by: gnn, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6747
Coverity points out that 'continue' is equivalent to 'break' in a do {}
while(false) loop.
Reported by: Coverity
CID: 1354983
Sponsored by: EMC / Isilon Storage Division
Use own protosw structures for both address families.
Check proto in encapcheck function and use -1 as proto argument in
encap_attach_func(), both address families can have IPPROTO_IPV4
and IPPROTO_IPV6 protocols.
Reported by: bz
RFC3173 says that the IP datagram MUST be sent in the original
non-compressed form, when the total size of a compressed payload
and the IPComp header is not smaller than the size of the original
payload. In tunnel mode for small packets IPComp will send
encapsulated IP datagrams without IPComp header.
Add ip_encap handler for IPPROTO_IPV4 and IPPROTO_IPV6 to handle
these datagrams. The handler does lookup for SA related to IPComp
protocol and given from mbuf source and destination addresses as
tunnel endpoints. It decapsulates packets only when corresponding SA
is found.
Reported by: gnn
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D6062
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
Set zero ivsize for enc_xform_null and remove special handling from
xform_esp.c.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D1503
degradation (7%) for host host TCP connections over 10Gbps links,
even when there were no secuirty policies in place. There is no
change in performance on 1Gbps network links. Testing GENERIC vs.
GENERIC-NOIPSEC vs. GENERIC with this change shows that the new
code removes any overhead introduced by having IPSEC always in the
kernel.
Differential Revision: D3993
MFC after: 1 month
Sponsored by: Rubicon Communications (Netgate)
Currently we perform crypto requests for IPSEC synchronous for most of
crypto providers (software, aesni) and only VIA padlock calls crypto
callback asynchronous. In synchronous mode it is possible, that security
policy will be removed during the processing crypto request. And crypto
callback will release the last reference to SP. Then upon return into
ipsec[46]_process_packet() IPSECREQUEST_UNLOCK() will be called to already
freed request. To prevent this we will take extra reference to SP.
PR: 201876
Sponsored by: Yandex LLC
defines the keys differently than NIST does, so we have to muck with
key lengths and nonce/IVs to be standard compliant...
Remove the iv from secasvar as it was unused...
Add a counter protected by a mutex to ensure that the counter for GCM
and ICM will never be repeated.. This is a requirement for security..
I would use atomics, but we don't have a 64bit one on all platforms..
Fix a bug where IPsec was depending upon the OCF to ensure that the
blocksize was always at least 4 bytes to maintain alignment... Move
this logic into IPsec so changes to OCF won't break IPsec...
In one place, espx was always non-NULL, so don't test that it's
non-NULL before doing work..
minor style cleanups...
drop setting key and klen as they were not used...
Enforce that OCF won't pass invalid key lengths to AES that would
panic the machine...
This was has been tested by others too... I tested this against
NetBSD 6.1.5 using mini-test suite in
https://github.com/jmgurney/ipseccfgs and the only things that don't
pass are keyed md5 and sha1, and 3des-deriv (setkey syntax error),
all other modes listed in setkey's man page... The nice thing is
that NetBSD uses setkey, so same config files were used on both...
Reviewed by: gnn
use CTASSERTs now that we have them...
Replace a draft w/ RFC that's over 10 years old.
Note that _AALG and _EALG do not need to match what the IKE daemons
think they should be.. This is part of the KABI... I decided to
renumber AESCTR, but since we've never had working AESCTR mode, I'm
not really breaking anything.. and it shortens a loop by quite
a bit..
remove SKIPJACK IPsec support... SKIPJACK never made it out of draft
(in 1999), only has 80bit key, NIST recommended it stop being used
after 2010, and setkey nor any of the IKE daemons I checked supported
it...
jmgurney/ipsecgcm: a357a33, c75808b, e008669, b27b6d6
Reviewed by: gnn (earlier version)
The IPsec SA statistic keeping is used even for decision making on expiry/rekeying SAs.
When there are multiple transformations being done the statistic keeping might be wrong.
This mostly impacts multiple encapsulations on IPsec since the usual scenario it is not noticed due to the code path not taken.
Differential Revision: https://reviews.freebsd.org/D3239
Reviewed by: ae, gnn
Approved by: gnn(mentor)
problems that was introduced in r285336... I have verified that
HMAC-SHA2-256 both ah only and w/ AES-CBC interoperate w/ a NetBSD
6.1.5 vm...
Reviewed by: gnn
mode and with hardware support on systems that have AESNI instructions.
Differential Revision: D2936
Reviewed by: jmg, eri, cognet
Sponsored by: Rubicon Communications (Netgate)
When IPSEC is enabled on the kernel the forwarding path has an optimization to not enter the code paths
for checking security policies but first checks if there is any security policy active at all.
The patch introduces the same optimization but for traffic generated from the host itself.
This reduces the overhead by 50% on my tests for generated host traffic without and SP active.
Differential Revision: https://reviews.freebsd.org/D2980
Reviewed by: ae, gnn
Approved by: gnn(mentor)
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
extension header type. The key_flush_sad() now will send SADB_EXPIRE
message when HARD lifetime expires. This is required by RFC 2367 and some
keying daemons rely on these messages. HARD lifetime messages have
precedence over SOFT lifetime messages, so now they will be checked first.
Also now SADB_EXPIRE messages will be send even the SA has not been used,
because keying daemons might want to rekey such SA.
PR: 200282, 200283
Submitted by: Tobias Brunner <tobias at strongswan dot org>
MFC after: 2 weeks
When we are passing mbuf to IPSec processing via ipsec[46]_process_packet(),
we hold one reference to security policy and release it just after return
from this function. But IPSec processing can be deffered and when we release
reference to security policy after ipsec[46]_process_packet(), user can
delete this security policy from SPDB. And when IPSec processing will be
done, xform's callback function will do access to already freed memory.
To fix this move KEY_FREESP() into callback function. Now IPSec code will
release reference to SP after processing will be finished.
Differential Revision: https://reviews.freebsd.org/D2324
No objections from: #network
Sponsored by: Yandex LLC
additional arguments - buffer and size of this buffer.
ipsec_address() is used to convert sockaddr structure to presentation
format. The IPv6 part of this function returns pointer to the on-stack
buffer and at the moment when it will be used by caller, it becames
invalid. IPv4 version uses 4 static buffers and returns pointer to
new buffer each time when it called. But anyway it is still possible
to get corrupted data when several threads will use this function.
ipsec_logsastr() is used to format string about SA entry. It also
uses static buffer and has the same problem with concurrent threads.
To fix these problems add the buffer pointer and size of this
buffer to arguments. Now each caller will pass buffer and its size
to these functions. Also convert all places where these functions
are used (except disabled code).
And now ipsec_address() uses inet_ntop() function from libkern.
PR: 185996
Differential Revision: https://reviews.freebsd.org/D2321
Reviewed by: gnn
Sponsored by: Yandex LLC
ipsec6_common_input_cb() uses partial copy of ip6_input() to parse
headers. But this isn't correct, when we use tunnel mode IPSec.
When we stripped outer IPv6 header from the decrypted packet, it
can become IPv4 packet and should be handled by ip_input. Also when
we use tunnel mode IPSec with IPv6 traffic, we should pass decrypted
packet with inner IPv6 header to ip6_input, it will correctly handle
it and also can decide to forward it.
The "skip" variable points to offset where payload starts. In tunnel
mode we reset it to zero after stripping the outer header. So, when
it is zero, we should requeue mbuf via netisr.
Differential Revision: https://reviews.freebsd.org/D2306
Reviewed by: adrian, gnn
Sponsored by: Yandex LLC
* in ipsec_encap() embed scope zone ids into link-local addresses
in the new IPv6 header, this helps ip6_output() disambiguate the
scope;
* teach key_ismyaddr6() use in6_localip(). in6_localip() is less
strict than key_sockaddrcmp(). It doesn't compare all fileds of
struct sockaddr_in6, but it is faster and it should be safe,
because all SA's data was checked for correctness. Also, since
IPv6 link-local addresses in the &V_in6_ifaddrhead are stored in
kernel-internal form, we need to embed scope zone id from SA into
the address before calling in6_localip.
* in ipsec_common_input() take scope zone id embedded in the address
and use it to initialize sin6_scope_id, then use this sockaddr
structure to lookup SA, because we keep addresses in the SADB without
embedded scope zone id.
Differential Revision: https://reviews.freebsd.org/D2304
Reviewed by: gnn
Sponsored by: Yandex LLC
The only thing is used from this code is ipip_output() function, that does
IPIP encapsulation. Other parts of XF_IP4 code were removed in r275133.
Also it isn't possible to configure the use of XF_IP4, nor from userland
via setkey(8), nor from the kernel.
Simplify the ipip_output() function and rename it to ipsec_encap().
* move IP_DF handling from ipsec4_process_packet() into ipsec_encap();
* since ipsec_encap() called from ipsec[64]_process_packet(), it
is safe to assume that mbuf is contiguous at least to IP header
for used IP version. Remove all unneeded m_pullup(), m_copydata
and related checks.
* use V_ip_defttl and V_ip6_defhlim for outer headers;
* use V_ip4_ipsec_ecn and V_ip6_ipsec_ecn for outer headers;
* move all diagnostic messages to the ipsec_encap() callers;
* simplify handling of ipsec_encap() results: if it returns non zero
value, print diagnostic message and free mbuf.
* some style(9) fixes.
Differential Revision: https://reviews.freebsd.org/D2303
Reviewed by: glebius
Sponsored by: Yandex LLC
where we want to create a new IP datagram.
o Add support for RFC6864, which allows to set IP ID for atomic IP
datagrams to any value, to improve performance. The behaviour is
controlled by net.inet.ip.rfc6864 sysctl knob, which is enabled by
default.
o In case if we generate IP ID, use counter(9) to improve performance.
o Gather all code related to IP ID into ip_id.c.
Differential Revision: https://reviews.freebsd.org/D2177
Reviewed by: adrian, cy, rpaulo
Tested by: Emeric POUPON <emeric.poupon stormshield.eu>
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Relnotes: yes
code.
Resurrect the state field in the struct secpolicy, it has
IPSEC_SPSTATE_ALIVE value when security policy linked in the chain,
and IPSEC_SPSTATE_DEAD value in all other cases. This field protects
from trying to unlink one security policy several times from the different
threads.
Take additional reference in the key_flush_spd() to be sure that policy
won't be freed from the different thread while we are sending SPDEXPIRE message.
Add KEY_FREESP() call to the key_unlink() to release additional reference
that we take when use key_getsp*() functions.
Differential Revision: https://reviews.freebsd.org/D1914
Tested by: Emeric POUPON <emeric.poupon at stormshield dot eu>
Reviewed by: hrs
Sponsored by: Yandex LLC
socket-buffer implementations, introduce a return value for MCLGET()
(and m_cljget() that underlies it) to allow the caller to avoid testing
M_EXT itself. Update all callers to use the return value.
With this change, very few network device drivers remain aware of
M_EXT; the primary exceptions lie in mbuf-chain pretty printers for
debugging, and in a few cases, custom mbuf and cluster allocation
implementations.
NB: This is a difficult-to-test change as it touches many drivers for
which I don't have physical devices. Instead we've gone for intensive
review, but further post-commit review would definitely be appreciated
to spot errors where changes could not easily be made mechanically,
but were largely mechanical in nature.
Differential Revision: https://reviews.freebsd.org/D1440
Reviewed by: adrian, bz, gnn
Sponsored by: EMC / Isilon Storage Division
IPv6. Initialize it only once in def_policy_init(). Remove its
initialization from key_init() and make it static.
Remove several fields from struct secpolicy:
* lock - it isn't so useful having mutex in the structure, but the only
thing we do with it is initialization and destroying.
* state - it has only two values - DEAD and ALIVE. Instead of take a lock
and change the state to DEAD, then take lock again in GC function and
delete policy from the chain - keep in the chain only ALIVE policies.
* scangen - it was used in GC function to protect from sending several
SADB_SPDEXPIRE messages for one SPD entry. Now we don't keep DEAD entries
in the chain and there is no need to have scangen variable.
Use TAILQ to implement SPD entries chain. Use rmlock to protect access
to SPD entries chain. Protect all SP lookup with RLOCK, and use WLOCK
when we are inserting (or removing) SP entry in the chain.
Instead of using pattern "LOCK(); refcnt++; UNLOCK();", use refcount(9)
API to implement refcounting in SPD. Merge code from key_delsp() and
_key_delsp() into _key_freesp(). And use KEY_FREESP() macro in all cases
when we want to release reference or just delete SP entry.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
ipsec_getpolicybyaddr()
ipsec4_checkpolicy()
ip_ipsec_output()
ip6_ipsec_output()
The only flag used here was IP_FORWARDING.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
and make its prototype similar to ipsec6_process_packet.
The flags argument isn't used here, tunalready is always zero.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
xform_ipip was used as fallback with low priority for IPIP
encapsulated packets that were decrypted. In some cases
it can decapsulate packets, that it shouldn't. This leads to situations,
when wrong configurations are magically working. Also it can propagate
wrong ingress interface and this can break security.
Now we redesigned the IPSEC code and IPIP encapsulation is called directly
from ipsec_output, and decapsulation is done in the ipsec_input with m_striphdr.
Differential Revision: https://reviews.freebsd.org/D1220
MFC after: 1 month
Sponsored by: Yandex LLC
- Wrong integer type was specified.
- Wrong or missing "access" specifier. The "access" specifier
sometimes included the SYSCTL type, which it should not, except for
procedural SYSCTL nodes.
- Logical OR where binary OR was expected.
- Properly assert the "access" argument passed to all SYSCTL macros,
using the CTASSERT macro. This applies to both static- and dynamically
created SYSCTLs.
- Properly assert the the data type for both static and dynamic
SYSCTLs. In the case of static SYSCTLs we only assert that the data
pointed to by the SYSCTL data pointer has the correct size, hence
there is no easy way to assert types in the C language outside a
C-function.
- Rewrote some code which doesn't pass a constant "access" specifier
when creating dynamic SYSCTL nodes, which is now a requirement.
- Updated "EXAMPLES" section in SYSCTL manual page.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Instead requeue mbuf back to IPv4 protocol handler. If there is one extra IP-IP
encapsulation, it will be handled with tunneling interface. And thus proper
interface will be exposed into mbuf's rcvif. Also, tcpdump that listens on tunneling
interface will see packets in both directions.
Sponsored by: Yandex LLC
For IPv6-in-IPv4, you may need to do the following command
on the tunnel interface if it is configured as IPv4 only:
ifconfig <interface> inet6 -ifdisabled
Code logic inspired from NetBSD.
PR: kern/169438
Submitted by: emeric.poupon@netasq.com
Reviewed by: fabient, ae
Obtained from: NETASQ
were primarily used to size the sysctl name list macros that were removed
in r254295. A few other constants either did not have an associated
sysctl node, or the associated node used OID_AUTO instead.
PR: ports/184525 (exp-run)
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
structure is used, but they already have equal fields in the struct
newipsecstat, that was introduced with FAST_IPSEC and then was merged
together with old ipsecstat structure.
This fixes kernel stack overflow on some architectures after migration
ipsecstat to PCPU counters.
Reported by: Taku YAMAMOTO, Maciej Milewski
examination shows, that although key_alloc_mbuf() could return chains,
the callers never use chains, so m_get2() should suffice.
Sponsored by: Nginx, Inc.
before passing a packet to protocol input routines.
For several protocols this mean that now protocol needs to
do subtraction itself, and for another half this means that
we do not need to add header length back to the packet.
Make ip_stripoptions() to adjust ip_len, since now we enter
this function with a packet header whose ip_len does represent
length of entire packet, not payload only.
in network byte order. Any host byte order processing is
done in local variables and host byte order values are
never[1] written to a packet.
After this change a packet processed by the stack isn't
modified at all[2] except for TTL.
After this change a network stack hacker doesn't need to
scratch his head trying to figure out what is the byte order
at the given place in the stack.
[1] One exception still remains. The raw sockets convert host
byte order before pass a packet to an application. Probably
this would remain for ages for compatibility.
[2] The ip_input() still subtructs header len from ip->ip_len,
but this is planned to be fixed soon.
Reviewed by: luigi, Maxim Dounin <mdounin mdounin.ru>
Tested by: ray, Olivier Cochard-Labbe <olivier cochard.me>
SAs. For now allow same address family bundles. While discovered with
ESP and AH, which does not make a lot of sense, IPcomp could be a possible
problematic candidate.
PR: kern/164400
MFC after: 3 days
the original IPv4 implementation from r178888:
- Use RT_DEFAULT_FIB in the IPv4 implementation where noticed.
- Use rt*fib() KPI with explicit RT_DEFAULT_FIB where applicable in
the NFS code.
- Use the new in6_rt* KPI in TCP, gif(4), and the IPv6 network stack
where applicable.
- Split in6_rtqtimo() and in6_mtutimo() as done in IPv4 and equally
prevent multiple initializations of callouts in in6_inithead().
- Use wrapper functions where needed to preserve the current KPI to
ease MFCs. Use BURN_BRIDGES to indicate expected future cleanup.
- Fix (related) comments (both technical or style).
- Convert to rtinit() where applicable and only use custom loops where
currently not possible otherwise.
- Multicast group, most neighbor discovery address actions and faith(4)
are locked to the default FIB. Individual IPv6 addresses will only
appear in the default FIB, however redirect information and prefixes
of connected subnets are automatically propagated to all FIBs by
default (mimicking IPv4 behavior as closely as possible).
Sponsored by: Cisco Systems, Inc.
comments to longer, also refining strange ones.
Properly use #ifdef rather than #if defined() where possible. Four
#if defined(PCBGROUP) occurances (netinet and netinet6) were ignored to
avoid conflicts with eventually upcoming changes for RSS.
Reported by: bde (most)
Reviewed by: bde
MFC after: 3 days
Unfold the IPSEC_COMMON_INPUT_CB() macro in xform_{ah,esp,ipcomp}.c
to not need three different versions depending on INET, INET6 or both.
Mark two places preparing for not yet supported functionality with IPv6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
- Remove contention on ISR during the crypto operation by using rwlock(9).
- Remove a second lookup of the SA in the callback.
Gain on 6 cores CPU with SHA1/AES128 can be up to 30%.
Reviewed by: vanhu
MFC after: 1 month
- AH does not release the SA like in ESP/IPCOMP when handling EAGAIN
- ipsec_process_done incorrectly release the SA.
Reviewed by: vanhu
MFC after: 1 week
DPCPU_DEFINE and VNET_DEFINE macros, as these cause problems for various
people working on the affected files. A better long-term solution is
still being considered. This reversal may give some modules empty
set_pcpu or set_vnet sections, but these are harmless.
Changes reverted:
------------------------------------------------------------------------
r215318 | dim | 2010-11-14 21:40:55 +0100 (Sun, 14 Nov 2010) | 4 lines
Instead of unconditionally emitting .globl's for the __start_set_xxx and
__stop_set_xxx symbols, only emit them when the set_vnet or set_pcpu
sections are actually defined.
------------------------------------------------------------------------
r215317 | dim | 2010-11-14 21:38:11 +0100 (Sun, 14 Nov 2010) | 3 lines
Apply the STATIC_VNET_DEFINE and STATIC_DPCPU_DEFINE macros throughout
the tree.
------------------------------------------------------------------------
r215316 | dim | 2010-11-14 21:23:02 +0100 (Sun, 14 Nov 2010) | 2 lines
Add macros to define static instances of VNET_DEFINE and DPCPU_DEFINE.
feature_present(3) checks.
This will help to run-time detect and conditionally handle specific
optionas of either feature in user space (i.e. in libipsec).
Descriptions read by: rwatson
MFC after: 2 weeks
legacy and IPv6 route destination address.
Previously in case of IPv6, there was a memory overwrite due to not enough
space for the IPv6 address.
PR: kern/122565
MFC After: 2 weeks
