that ppp stays in the foreground.
o Add the -quiet switch to quieten ppps startup
o Add the -nat flag and discourage the use of the -alias flag. Both do
the same thing.
o Correct some nat usage strings.
o Change the internal ``alias'' command to ``nat''.
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.
Ppp controls the phone number, but idle timers and
SYNC/RAW decisions are still made by isdnd (in isdnd.rc).
This involves a new datalink state machine phase. The
``wait for carrier'' phase happens after dialing but
before logging in. The whole dial state should really
be abstracted so that each device type can deal with it
in its own way (thinking about PPPoE) - but that'll have
to wait.
The ``set cd'' symantics remain the same for tty devices,
but we now delay until we either get CD or timeout waiting
(at which time we drop the link if we require CD).
For i4b devices we always insist on carrier.
Thanks to hm@ for his help, and especially for pointing out
that I *don't* need to re-implement isdnd (that was a huge
waste of time !) :-]
o If we're using RADIUS and the RADIUS mtu is less than our
peers mru/mrru, reduce our mtu to this value for NetBSD too.
o Make struct throughput's sample period dynamic and tweak the ppp
version number to reflect the extra stuff being passed through
the local domain socket as a result (MP mode).
o Measure the current throughput based on the number of samples actually
taken rather than on the full sample period.
o Keep the throughput statisics persistent while being passed to
another ppp invocation through the local domain socket.
o When showing throughput statistics after the timer has stopped, use
the stopped time for overall calculations, not the current time.
Also show the stopped time and how long the current throughput has
been sampled for.
o Use time() consistently in throughput.c
o Tighten up the ``show bundle'' output.
o Introduce the ``set bandwidth'' command.
o Rewrite the ``set autoload'' command. It now takes three arguments
and works based on a rolling bundle throughput average compared against
the theoretical bundle bandwidth over a given period (read: it's now
functional).
negate the sense of rules.
o Remove the redundant (and undocumented) ``host'' and ``port''
words (README.changes updated).
o Don't permit (and ignore) garbage instead of the protocol.
Mostly submitted by: Peter Jeremy <jeremyp@gsmx07.alcatel.com.au>
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.
A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.
This proves that PPPoE is plausable in userland....
This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !
iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.
The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').
Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.
Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.
Assign our physical device name for incoming tcp connections by
calling getpeername().
Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().
the layering.
We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.
Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.
o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.
we're already in network phase and our autoload values
are set with no minimum threshold (the default).
Tell the autoload timer that it's ``coming up'' *before*
calling AutoLoadTimeout() directly... not after. This
prevents the very first demand-dial connection from
immediately disconnecting when there are other auto links.
Problem diagnosis: Ted Mittelstaedt <tedm@toybox.placo.com>
input routines and take advantage of the new init/continue
interface in libradius. This allows a timely response on
other links in an MP setup while RADIUS requests are in
progress as well as the ability to handle other data from
the peer in parallel. It should also make the future addition
of PAM support trivial.
While I'm in there, validate pap & chap header IDs if
``idcheck'' is enabled (the default) for other FSM packet
types.
NOTE: This involved integrating the generation of chap
challenges and the validation of chap responses
(and commenting what's going on in those routines).
I currently have no way of testing ppps ability
to respond to M$Chap CHALLENGEs correctly, so if
someone could do the honours, it'd be much
appreciated (it *looks* ok!).
Sponsored by: Internet Business Solutions Ltd., Switzerland
details. Compiling with -DNORADIUS (the default for `release')
removes support.
TODO: The functionality in libradius::rad_send_request() needs
to be supplied as a set of routines so that ppp doesn't
have to wait indefinitely for the radius server(s). Instead,
we need to get a descriptor back, select() on the descriptor,
and ask libradius to service it when necessary.
For now, ppp blocks SIGALRM while in rad_send_request(), so
it misses PAP/CHAP retries & timeouts if they occur.
Only PAP is functional. When CHAP is attempted, libradius
complains that no User-Password has been specified... rfc2138
says that it *mustn't* be used for CHAP :-(
Sponsored by: Internet Business Solutions Ltd., Switzerland
to see if there's anything to do, schedule the next alarm
based on the next required timeout.
This decreases the load when there are lots of relatively
idle ppp processes.
While I'm in there, handle the possibility that a timeout
makes the timer element go out of scope by grabbing the
enext pointer before executing the timer function.
exits, it causes a select() exception.
Handle these select() exceptions on link descriptors in pretty
much the same way as loss of carrier rather than dropping out
in confusion.
for our interface address. We're about to call ip_Input()
anyway, and ip_Input() does the PacketAliasIn().
Stack trace provided by: Cameron Grant <gandalf@vilnya.demon.co.uk>
are done in the same way as command execution.
For example, ``set proctitle USER INTERFACE PROCESSID'' would
be useful in a -direct profile for identifying who's connected.
for every machine on every class C or smaller subnet that we
route to.
Add ``set {send,recv}pipe'' for controlling our socket buffer
sizes.
Mention the IP number with the problem in a few error messages.
All submitted by: Craig Leres <leres@ee.lbl.gov>
Modified slightly by: me
shortseq, authname and authkey.
o Auth{name,key} may additionally be set in PHASE_ESTABLISH.
o The others may be set in PHASE_ESTABLISH as long as no links
have yet reached DATALINK_LCP.
demand-dial links with dynamic IP numbers where the program
that causes the dial bind()s to an interface address that is
subsequently changed after ppp negotiation.
The problem is defeated by adding negotiated addresses to the
tun interface as additional alias addresses and providing a set
of ``iface'' commands for managing the interface. Libalias is
also required (and what a name clash!) - it happily IP-aliases
the address so that the source is that of the primary (negotiated)
interface and un-IP-aliases it on the way back.
An ``enable iface-alias'' is done implicitly by the -alias command
line switch. If -alias isn't given, iface-aliasing is disabled by
default and can't be enabled 'till an ``alias enable yes'' is done.
``alias enable no'' silently disables iface-alias.
So, for dynamic-IP-type-connections, running ``ppp -alias -auto blah''
will work for the first connection, although existing bindings will
not survive a disconnect/connect as the TCP peer will be trying to
send to the old IP address - the packets won't route.
It's now a lot easier to add IPXCP to ppp with minor updates to
the new iface.[ch] (if anyone ever gets 'round to it).
It's also now possible to manually add interface aliases with
something like ``iface add 1.2.3.4/24 5.6.7.8''. This allows
multi-homed ppp links :-)
anything for two mintues (see ``set choked'' and ``show
bundle''), nuke the ip, mp and link level buffer queues.
This should fix problems where ``ppp -auto'' seems to stop
responding after failing to connect to the peer a few times.
the device is successfully opened. If we fail to open it,
mention the fact.
Also go back into command mode as soon as the device is closed
rather than waiting for the user to type something before noticing.
(see the new ``set callback'' and ``set cbcp'' commands)
o Add a ``cbcp'' log level and mbuf type.
o Don't dump core when \T is given in ``set login'' or
``set hangup''.
o Allow ``*'' and blanks as placeholders in ppp.secret and
allow a fifth field for specifying auth/cbcp dialback
parameters.
o Remove a few extraneous #includes
o Define the default number of REQs (restart counter) in defs.h
rather than hardcoding ``5'' all over the place.
o Fix a few man page inconsistencies.
``add .... HISADDR''. The network will never be
reachable at this point unless we're in -auto or reading
the command from ppp.linkup.
We can now run the following lines and get the expected
results:
set ifaddr 1.2.3.4/0 5.6.7.8/0
add default HISADDR
where a route is added immediately in auto mode and the
whole thing is delayed 'till the IP numbers have been
agreed in other modes.
Essentially, ppp.linkup is no longer required.
end up writing zero bytes, sleep for 1/10 of a second so that
we don't end up using up too much cpu.
This should only ever happen on systems that wrongly report a
descriptor as writable despite the tty buffer being full.
Discussed with: Jeff Evarts
o Do an initial run-time check to see if select() alters the passed
timeval. This knowledge isn't yet used, but will be soon.
for all datalinks in a bundle. Ppp now deals correctly
with link types that are changed while open
o When changing the type of the last AUTO link, only clear
the interface if we're not in PHASE_NETWORK. This allows
us to switch to -ddial mode while we have a connection
without suddenly unexpectedly throttling ourselves by
clearing the interface configuration.
Problem area noted by: Aaron Jeremias Luz <aaron@csh.rit.edu>
*after* shuffling fragments from the IP queue into the
individual link queues.
This fixes a latency problem pointed out by: Bruce Evans <bde@zeta.org.au>
