The backpressure indication is implemented using an unlimited rate type of
mbuf send tag. When the upper layers typically the socket layer has obtained such
a tag, it can then query the destination driver queue for the current
amount of space available in the send queue.
A single mbuf send tag may be referenced multiple times and a refcount has been added
to the mlx5e_priv structure to track its usage. Because the send tag resides
in the mlx5e_channel structure, there is no need to wait for refcounts to reach
zero until the mlx4en(4) driver is detached. The channels structure is persistant
during the lifetime of the mlx5en(4) driver it belongs to and can so be accessed
without any need of synchronization.
The mlx5e_snd_tag structure was extended to contain a type field, because there are now
two different tag types which end up in the driver which need to be distinguished.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
In order to enable HW LRO, both the "hw_lro" sysctl in the mlx5en(4) config
space must be set, and the ifconfig(8) LRO capability must be set. Any other
settings will disable HW LRO.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add counter for all transmitted and received bytes. Currently only all
transmitted and received packets were counted. Fix description of RX LRO
counters while at it.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
By allocating the worst case size channel structure array
at attach time we can eliminate various NULL checks in the
fast path. And also reduce the chance for use-after-free
issues in the transmit fast path.
This change is also a requirement for implementing
backpressure support.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Writing to the debug stats variable must be locked,
else serialization will be lost which might cause
various kernel panics due to creating and destroying
sysctls out of order.
Make sure the sysctl context is initialized after freeing
the sysctl nodes, else they can be freed twice.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Inspect the ethernet compliance code to figure out actual cable type by reading
the PDDR module info register.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This can happen when connections are short lived and leads to
a firmware error printout in dmesg, syndrome 0x51cfb0, because
the SQ is in the wrong state.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
1) Don't exceed the drivers own hardcoded TX inline limit.
The blueflame register size can be much greater than the hardcoded limit
for inlining. Make sure we don't exceed the drivers own limit, because this
also means that the maximum number of TX fragments becomes invalid and
then memory size assumptions in the TX path no longer hold up.
2) Make sure the mlx5_query_min_inline() function returns an error code.
3) Header inlining is required when using TSO.
4) Catch failure to compute inline header size for TSO.
5) Add support for UDP when computing inline header size.
6) Fix for inlining issues with regards to DSCP.
Make sure we inline 4 bytes beyond the ethernet and/or
VLAN header to workaround a hardware bug extracting
the DSCP field from the IPv4/v6 header.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The hardware queues are deep enough currently and using the DRBR and associated
callbacks only leads to more task switching in the TX path. The is also a race
setting the queue_state which can lead to hung TX rings.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for setting the bandwidth limit as a ratio rather than in bits per
second. The ratio must be an integer number between 1 and 100 inclusivly.
Implement the needed firmware commands and SYSCTLs through mlx5en(4).
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Make sure the active width and speed is set in case the
translate_eth_proto_oper() function doesn't recognize the
current port operation mask.
Linux commit:
7672ed33c4c15dbe9d56880683baaba4227cf940
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
If the mlx5_ib_read_cong_stats() function was running when mlx5ib was unloaded,
because this function unconditionally restarts the timer, the timer can still
be pending after the delayed work has been cancelled. To fix this simply loop
on the delayed work cancel procedure as long as it returns non-zero.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Although "create_srq_user" does overwrite "in.pas" on some paths, it
also contains at least one feasible path which does not overwrite it.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
"fw_rev_min(dev->mdev)" with type "unsigned short" (16 bits, unsigned) is
promoted in "fw_rev_min(dev->mdev) << 16" to type "int" (32 bits, signed), then
sign-extended to type "unsigned long" (64 bits, unsigned). If
"fw_rev_min(dev->mdev) << 16" is greater than 0x7FFFFFFF, the upper bits of the
result will all be 1.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
Driver description should be set by core and not by the Ethernet driver.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
A command is either polling or event driven and the mode cannot change
during execution of a command. Make sure the event handler only handle
commands which are not polled. This is done by checking the command mode
in the command handler before completing commands.
Submitted by: hselasky@
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
This counter will represent transmitted packets which has more than
1518 octets.
The NIC has multiple hardware counters for counting transmitted
packets larger than 1518 octets. Each counter counts the packets
in specific range.
We accumulate those counters to have a single counter.
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
All other mlx5_events report the port number as 1 based, which is how FW
reports it in the port event EQE. Reporting 0 for this event causes
mlx5_ib to not raise a fatal event notification to registered clients
due to a seemingly invalid port.
All switch cases in mlx5_ib_event that go through the port check are
supposed to set the port now, so just do it once at variable
declaration.
Linux commit:
aba462134634b502d720e15b23154f21cfa277e5
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
The user can provide very large cqe_size which will cause to integer
overflow.
Linux commit:
28e9091e3119933c38933cb8fc48d5618eb784c8
Approved by: hselasky (mentor)
MFC after: 1 week
Sponsored by: Mellanox Technologies
If power exceed the slot limit, or slot limit is unknown the ConnectX-6
firmware will shutdown its port.
Inform the user via debug message.
MFC after: 3 days
Approved by: hselasky (mentor), kib (mentor)
Sponsored by: Mellanox Technologies
The receive side scaling stride parameter is a value which define the interval
between active receive side queues. The traffic for the inactive queues is
redirected to the nearest active queue by use of modulus. The default value
of this parameter is one, which means all receive side queues are used.
The point of this feature is to redirect more traffic to fewer receive side
queues in order to take more advantage of sorted large receive offload,
sorted LRO. The sorted LRO works better when more packets are accumulated
per service interval.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Inspecting the PRM no more than 0x3F data segments, DS, of size 16 bytes is
allowed.
Worst case scenario summary of DS usage:
Header is fixed: 2 DS
Maximum inlining: 98 => (98 - 2) / 16 = 6 DS
Remainder: 0x3F - 2 - 6 = 55 DS (mbuf frags)
Previously a value of 56 DS was used and this would work in the
normal case because not all inline data area was used up.
MFC after: 3 days
Approved by: re (marius)
Sponsored by: Mellanox Technologies
Query the minimal inline mode supported by the card.
When creating a send queue, cache the queried mode and optimize the transmit
if no inlining is required. In this case, we can avoid touching the headers
cache line and avoid dirtying several more lines by copying headers into
the send WQEs. Also, if no inline headers are used, hardware assists in
the VLAN tag framing.
Submitted by: kib@, slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
For setups having a large amount of PCI devices, it makes sense to limit the
number of MSIX vectors per PCI device, in order to avoid running out of IRQ
vectors.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The scatter list is formed by the chunks of MCLBYTES each, and larger
than default packets are returned to the stack as the mbuf chain.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
