safe since the 802.11 layer does the right thing for 11a operation)
o select short preamble operation based on the negotiated capabilities; not
just the local state/capability
o fillin the duration field in the 802.11 header as appropriate
o remove detection of 11g support; no longer needed
Obtained from: MADWIFI (with modifications)
capabilities for outbound management frames. But beware of sending
this when operating on 5GHz channels; some 11a AP's reject association
requests if this bit is set in the capabilities listed.
Obtained from: MADWIFI (with modifications)
special signal-delivery protections for setugid processes. In the
event that a system is relying on "unusual" signal delivery to
processes that change their credentials, this can be used to work
around application problems.
Also, add SIGALRM to the set of signals permitted to be delivered to
setugid processes by unprivileged subjects.
Reported by: Joe Greco <jgreco@ns.sol.net>
we're on a 32-bit/64-bit bus or not. Use this to decide if we should
set the PCI dual-address cycle enable bit in the C+ command register.
(Enabling DAC on a 32-bit bus seems to do bad things.)
Also, initialize the C+ command register early in the re_init() routine.
The documentation says this register should be configured first.
in6_pcbpurgeif0(LIST_FIRST(udbinfo.listhead), ifp);
in6_pcbpurgeif0(LIST_FIRST(ripcbinfo.listhead), ifp);
The problem here is that udbinfo.listhead and ripcbinfo.listhead are
not initialized during the device probe/attach phase of the kernel
boot process. So if, for example, a network driver calls ether_ifattach()
in its foo_attach() routine and then decides that something is wrong
and calls ether_ifdetach() to reverse the process, we will panic trying
to dereference the uninitialized list head pointers. (Though the
same sequence of events performed after the kernel has come up works
file, i.e. doing kldload if_foo from multiuser.)
Change this to:
if (udbinfo.listhead != NULL)
in6_pcbpurgeif0(LIST_FIRST(udbinfo.listhead), ifp);
if (ripcbinfo.listhead != NULL)
in6_pcbpurgeif0(LIST_FIRST(ripcbinfo.listhead), ifp);
to avoid the NULL pointer dereferences.
pmap_remove_pte(), passed NULL instead of the required page table
page to pmap_unuse_pt(). Compute the necessary page table page
in pmap_remove_pte(). Also, remove some unreachable code from
pmap_remove_pte().
count in _vm_object_allocate(). (Access to the generation count is
governed by the vm object's lock.) Note: the introduction of the
atomic increment in revision 1.238 appears to be an accident. The
purpose of that commit was to fix an Alpha-specific bug in UMA's
debugging code.
We simply use the detected FIFO size to determine whether we have
a post 16550 UART or not. The support lacks proper serialization of
hardware access for now.
pmap_extract_and_hold(). Note, however, that GIANT_REQUIRED should not be
removed until all platforms fully implement the "prot" parameter to
pmap_extract_and_hold().
Reviewed by: tegge
fixes a longstanding issue WRT resetting the chip after startup- it
would fail if we were connected as an F-port to a switch. If we
were connected as an F-port, we got assigned a hard loop ID of 255,
which is really a bogus loop id. Then when we turned around to
reset ourselves, the firmware would reject the ICB_INIT request
because the loop id was bogus. *sputter*
Minor fixlet from somebody in NetBSD with too much time on their
hands (dma -> DMA).
the "compatible" property too in the ns8250 case. This gets the serial
console to work on Blade 100s, where the device name is just "serial".
Reviewed by: marcel
Second (PPS) timing interface. The support is non-optional and by
default uses the DCD line signal as the pulse input. A compile-time
option (UART_PPS_ON_CTS) can be used to have uart(4) use the CTS line
signal.
Include <sys/timepps.h> in uart_bus.h to avoid having to add the
inclusion of that header in all source files.
Reviewed by: phk
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
