fault. In r188331 this update was relocated because of synchronization
changes to a place where it would occur on both hard and soft faults. This
change again restricts the update to hard faults.
required to make 3CR990 familiy controllers run on NV flash
firmware version 03.001.008.
The latest firmware added HMAC digest information so teach txp(4)
to pass them to sleep image before downloading is started.
While I'm here restore previous IMR/IER register if firmware
downloading have failed.
PR: kern/89876, kern/132047
The old BTX passed the general purpose registers from the 32-bit client to
the routines called via virtual 86 mode. The new BTX did the same thing.
However, it turns out that some instructions behave differently in virtual 86
mode and real mode (even though this is under-documented). For example, the
LEAVE instruction will cause an exception in real mode if any of the upper
16-bits of %ebp are non-zero after it executes. In virtual 8086 mode the
upper 16-bits are simply ignored. This could cause faults in hardware
interrupt handlers that inherited an %ebp larger than 0xffff from the 32-bit
client (loader, boot2, etc.) while running in real mode.
To fix, when executing hardware interrupt handlers provide an explicit clean
state where all the general purpose and segment registers are zero upon
entry to the interrupt handler. While here, I attempted to simplify the
control flow in the 'intusr' code that sets up the various stack frames
and exits protected mode to invoke the requested routine via real mode.
A huge thanks to Tor Egge (tegge@) for debugging this issue.
Submitted by: tegge
Reviewed by: tegge
Tested by: bz
MFC after: 1 week
function, done in r188334. Instead, collect the entries that shall be
freed, in the deferred_freelist member of the map. Automatically purge
the deferred freelist when map is unlocked.
Tested by: pho
Reviewed by: alc
an NFS file. Now the priming is conditional on a new
vfs.nfs.prime_access_cache sysctl. For now I've left the default setting
to disabling the priming.
Requested by: scottl
checks for the tcpcb, previously used to detect complete disconnection,
with INP_DROPPED checks. Correct that, preventing shutdown() from
improperly generating a TCP segment with destination IP and port of
0.0.0.0:0.
PR: kern/132050
Reported by: david gueluy <david.gueluy at netasq.com>
MFC after: 3 weeks
- We don't need to exit the Giant mutex when sleeping. This is done
automatically. Replace Giant by NULL mutex for all control requests in the
enumeration path.
- Optimise away duplicate alternate interface selection requests in USB Host
mode.
Submitted by: Hans Petter Selasky
Improvements to "usb2_transfer_setup()" and "usb2_transfer_unsetup()". Set
"ppxfer[n]" when the transfer setup is complete to prevent races. Remove
redundant NULL-checks from "usb2_transfer_unsetup()".
Submitted by: Hans Petter Selasky
- The software computed HID size is not always correct, because the algoritm
does not handle unsorted HID descriptors.
- Change the way we obtain the report ID.
- Use the X/Y/Z+button locations instead for report ID source for ums.
- Add more range checks.
- Remove Microsoft Mouse quirks. If the positions are moduloed the report
length multiplied by 8, the values seem correct.
- Some minor style changes.
Submitted by: Hans Petter Selasky
o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o add output mux support
o gpio pin count is chip-dependent
o 9280 and 9285 do input handling different
o hookup gpio interrupts
o no need to save/restore soft led state around reset
