Partially implement generic_bs_*_8() for MIPS platforms.
This is known to work with TARGET_ARCH=mips64 with FreeBSD/BERI.
Assuming that other definitions in cpufunc.h are correct it will
work on non-o64 ABI systems except sibyte. On sibyte and o32 systems
generic_bs_*_8() will remain panic() implementations.
Sponsored by: DARPA, AFRL
Reviewed by: imp, jmallett (older versions)
(Wasting 4k just as a temporary placeholder for a boot environment seems
a bit ridiculous, but hey.)
Tested: gxemul:
$ gxemul -e malta -d i:/home/adrian/work/freebsd/svn/mfsroot-rspro.img -C 4Kc /tftpboot/kernel.MALTA
to unique values.
There's some confusion about what the n32 assembler API really is
(since on page 9 of the spec they say that t0-t3 don't exist, then
turn around on page 22 and say that t4-t7 don't exist), and this
doesn't touch that.
NetBSD's version of this file follows the convention I used here, and
is likely to be correct.
This should fix gdb/ptrace.
sys/arm and sys/mips), squelching the clang 3.3 warnings about this.
Noticed by: tinderbox and many irate spectators
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
PR: kern/177759
MFC after: 3 days
Having MIPS_MAX_TLB_ENTRIES defined to 128 is misleading, since it used
to be 64 in older releases of MIPS architecture (where it could be read
from Config1) and can be much more than 128 for the newer processors.
For now, move the definition to the only file using it (mips/mips/tlb.c)
and define MIPS_MAX_TLB_ENTRIES depending on the MIPS cpu defined. Also
add few checks so that we do not write beyond the end of the tlb_state
array.
This fixes a kernel data corruption seen in Netlogic XLP, which was casued
by tlb_save() writing beyond the end of tlb_state array when breaking into
debugger.
Introduce counter(9) API, that implements fast and raceless counters,
provided (but not limited to) for gathering of statistical data.
See http://lists.freebsd.org/pipermail/freebsd-arch/2013-April/014204.html
for more details.
In collaboration with: kib
Reviewed by: luigi
Tested by: ae, ray
Sponsored by: Nginx, Inc.
* arge0 is MII
* arge1 is GMII
* the MDIO bus is on arge1, not arge0
* the default switch config is to have ports 0-3 as the switch group,
with port 4 being an external PHY dedicated to arge0 (ie, 'cpu' port.)
Whilst I'm here, remove unused bits and pieces from the config.
Tested:
* AP121, ping on both arge0 and arge1
* Tested switch port detection using etherswitchcfg
* Enable RX and host interrupts during bus probe/attach
* Disable all interrupts (+ host ISR) during bus detach
* Enable TX DONE interrupt only when we start transmitting; clear it when
we're done.
* The RX/TX FIFO depth is still conjecture on my part. I'll fix this
shortly.
* The TX FIFO interrupt isn't an "empty" interrupt, it's an "almost empty"
interrupt. Sigh. So..
* .. in ar933x_bus_transmit(), wait for the FIFO to drain before
continuing.
I dislike having to wait for the FIFO to drain, alas.
Tested:
* Atheros AP121 board, AR9331 SoC.
TODO:
* RX/TX overflow, RX error, BREAK support, etc.
* Figure out the true RX/TX FIFO depth.
This implements the bus transmit/receive/sigchg/ipend methods with
a polled interrupt handler (ipend) rather than enabling hardware
interrupts.
The FIFO is faked at 16 bytes deep for now, just so the transmit
IO side doesn't suck too bad (the callout frequency limits how quickly
IO is flushed to the sender, rather than scheduling the callout more
frequently whilst there's active TX. But I digress.)
Tested:
* Atheros AP121 (AR9330) reference board, booting to multi-user interactive
mode.
most kernels before FreeBSD 9.0. Remove such modules and respective kernel
options: atadisk, ataraid, atapicd, atapifd, atapist, atapicam. Remove the
atacontrol utility and some man pages. Remove useless now options ATA_CAM.
No objections: current@, stable@
MFC after: never
uart(4) allocates send and receiver buffers in attach() before it calls
the low-level driver's attach routine. Many low-level drivers set the
fifo sizes in their attach routine, which is too late. Other drivers set
them in the probe() routine, so that they're available when uart(4)
allocates buffers. This fixes the ones that were setting the values too
late by moving the code to probe().
* Add baud rate and divisor programming code. See below for more
information.
* Flesh out ar933x_init() to disable interrupts and program the initial
console setup.
* Remove #if 0'ed code from ar933x_term().
* Explain what these functions do.
Now, the baud rate and divisor code comes from Linux, as a submission
to the OpenWRT project and Linux kernel from
Gabor Juhos <juhosg@openwrt.org>.
The original ticket for this code is https://dev.openwrt.org/ticket/12031 .
I've contacted Gabor and asked for his permission to also licence the patch
in question (which covers this code) to BSD lience and he's agreed.
Hence why I'm including it here in FreeBSD.
Tested:
* AP121 (AR9330)
* Default clock is 25MHz;
* Remove the UART register macro here - it's not needed as we don't need
to "adjust" the register offset / spacing at all;
* Remove unused fields in the softc.
Tested:
* AP121
This implements the kernel glue needed (getc, putc, rxready).
This isn't a 16550 UART, even if the datasheet overview claims so.
The Linux ar933x support was used as a reference, however the uart code
is a reimplementation.
Attentive viewers will note that the uart code is based off of the ns8250
code and the UART bus code is a stubbed-out version of this. I'll be
replacing it with non-stubbed versions soon, making this a fully featured
driver.
Tested:
* AP121 reference board (AR933x), booting through the mountroot> prompt;
then doing some basic interactive tests in ddb.
This was ported from the AR724x code and I think that also doesn't
quite work. I'll investigate that soon.
With this in place the system reset path works, so 'reset' from kdb
actually resets the SoC.
Tested:
* AP121 test board
CPUs.
The AR933x is a mips24k based SoC with an AR9380 series SoC on board,
two gigabit ethernet interfaces and an internal 10/100mbit ethernet
switch. There's also the normal interfaces (USB, ethernet, uart, GPIO.)
The downside? There's a non-ns8250 UART device.
With a very basic UART driver (not in this commit) the SoC is initialised
and boots up. I'll commit the UART code soon and then link it into the
general setup path.
This code is a re-implementation based from the Linux kernel / openwrt
AR933x support.
TODO:
* UART (obviously)
* All of the ethernet, USB and wifi SoC glue, including ethernet PLL
programming.
do not map the b_pages pages into buffer_map KVA. The use of the
unmapped buffers eliminate the need to perform TLB shootdown for
mapping on the buffer creation and reuse, greatly reducing the amount
of IPIs for shootdown on big-SMP machines and eliminating up to 25-30%
of the system time on i/o intensive workloads.
The unmapped buffer should be explicitely requested by the GB_UNMAPPED
flag by the consumer. For unmapped buffer, no KVA reservation is
performed at all. The consumer might request unmapped buffer which
does have a KVA reserve, to manually map it without recursing into
buffer cache and blocking, with the GB_KVAALLOC flag.
When the mapped buffer is requested and unmapped buffer already
exists, the cache performs an upgrade, possibly reusing the KVA
reservation.
Unmapped buffer is translated into unmapped bio in g_vfs_strategy().
Unmapped bio carry a pointer to the vm_page_t array, offset and length
instead of the data pointer. The provider which processes the bio
should explicitely specify a readiness to accept unmapped bio,
otherwise g_down geom thread performs the transient upgrade of the bio
request by mapping the pages into the new bio_transient_map KVA
submap.
The bio_transient_map submap claims up to 10% of the buffer map, and
the total buffer_map + bio_transient_map KVA usage stays the
same. Still, it could be manually tuned by kern.bio_transient_maxcnt
tunable, in the units of the transient mappings. Eventually, the
bio_transient_map could be removed after all geom classes and drivers
can accept unmapped i/o requests.
Unmapped support can be turned off by the vfs.unmapped_buf_allowed
tunable, disabling which makes the buffer (or cluster) creation
requests to ignore GB_UNMAPPED and GB_KVAALLOC flags. Unmapped
buffers are only enabled by default on the architectures where
pmap_copy_page() was implemented and tested.
In the rework, filesystem metadata is not the subject to maxbufspace
limit anymore. Since the metadata buffers are always mapped, the
buffers still have to fit into the buffer map, which provides a
reasonable (but practically unreachable) upper bound on it. The
non-metadata buffer allocations, both mapped and unmapped, is
accounted against maxbufspace, as before. Effectively, this means that
the maxbufspace is forced on mapped and unmapped buffers separately.
The pre-patch bufspace limiting code did not worked, because
buffer_map fragmentation does not allow the limit to be reached.
By Jeff Roberson request, the getnewbuf() function was split into
smaller single-purpose functions.
Sponsored by: The FreeBSD Foundation
Discussed with: jeff (previous version)
Tested by: pho, scottl (previous version), jhb, bf
MFC after: 2 weeks
pages around, taking array of vm_page_t both for source and
destination. Starting offsets and total transfer size are specified.
The function implements optimal algorithm for copying using the
platform-specific optimizations. For instance, on the architectures
were the direct map is available, no transient mappings are created,
for i386 the per-cpu ephemeral page frame is used. The code was
typically borrowed from the pmap_copy_page() for the same
architecture.
Only i386/amd64, powerpc aim and arm/arm-v6 implementations were
tested at the time of commit. High-level code, not committed yet to
the tree, ensures that the use of the function is only allowed after
explicit enablement.
For sparc64, the existing code has known issues and a stab is added
instead, to allow the kernel linking.
Sponsored by: The FreeBSD Foundation
Tested by: pho (i386, amd64), scottl (amd64), ian (arm and arm-v6)
MFC after: 2 weeks
future further optimizations where the vm_object lock will be held
in read mode most of the time the page cache resident pool of pages
are accessed for reading purposes.
The change is mostly mechanical but few notes are reported:
* The KPI changes as follow:
- VM_OBJECT_LOCK() -> VM_OBJECT_WLOCK()
- VM_OBJECT_TRYLOCK() -> VM_OBJECT_TRYWLOCK()
- VM_OBJECT_UNLOCK() -> VM_OBJECT_WUNLOCK()
- VM_OBJECT_LOCK_ASSERT(MA_OWNED) -> VM_OBJECT_ASSERT_WLOCKED()
(in order to avoid visibility of implementation details)
- The read-mode operations are added:
VM_OBJECT_RLOCK(), VM_OBJECT_TRYRLOCK(), VM_OBJECT_RUNLOCK(),
VM_OBJECT_ASSERT_RLOCKED(), VM_OBJECT_ASSERT_LOCKED()
* The vm/vm_pager.h namespace pollution avoidance (forcing requiring
sys/mutex.h in consumers directly to cater its inlining functions
using VM_OBJECT_LOCK()) imposes that all the vm/vm_pager.h
consumers now must include also sys/rwlock.h.
* zfs requires a quite convoluted fix to include FreeBSD rwlocks into
the compat layer because the name clash between FreeBSD and solaris
versions must be avoided.
At this purpose zfs redefines the vm_object locking functions
directly, isolating the FreeBSD components in specific compat stubs.
The KPI results heavilly broken by this commit. Thirdy part ports must
be updated accordingly (I can think off-hand of VirtualBox, for example).
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff
Reviewed by: pjd (ZFS specific review)
Discussed with: alc
Tested by: pho
Switch eventtimers(9) from using struct bintime to sbintime_t.
Even before this not a single driver really supported full dynamic range of
struct bintime even in theory, not speaking about practical inexpediency.
This change legitimates the status quo and cleans up the code.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
The changes are:
- the microcore code loaded into the NAE has to be byteswapped
in LE
- the descriptors in memory for a P2P NAE descriptor has to be
byteswapped in LE
- the m_data pointer is already cacheline aligned, so the
unnecessary m_adj to cacheline size can be removed
- fix mask used to obtain physical address from the Tx freeback
descriptor
- fix a compile error in code under #ifdef
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
The CMS output queue credit configuration register is 64 bit, so use
a 64 bit variable while updating it.
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
Update MDIO reset code to support Broadcom XLP B1 revisions.
Update nlm_xlpge_ioctl, nlm_xlpge_port_enable need not be
called after nlm_xlpge_init.
Obtained from: Venkatesh J V <venkatesh.vivekanandan@broadcom.com>
Support few more versions of board firmware. In case the security
block is disabled, enable it at boot. Also increase the excluded
memory region to cover the area used by the firmware to initialize
devices.
Update the function xlp_pcib_hardware_swap_enable() to do nothing
when BYTE_ORDER is not BIG_ENDIAN. PCIe hardware swap is not requred
in little-endian mode as the endianness matches that of CPU.
Write FDT attachment for the Terasic MTL (multitouch LCD) driver.
Exploit the fact that FDT allows multiple memory ranges to be
assigned to a device, giving us a cleaner description than
device.hints does.
Portions of this changeset that remove mtl from BERI device.hints and
add to DTS will be merged separately.
Sponsored by: DARPA, AFRL
