affects cases where there is a slave but no master. These bugs
were usually recovered from provided ATAPI was configured, but only
after lengthy delays. Configuring ATAPI still fixes some bugs for
non-atapi drives.
Don't wait for seek complete in wdreset(). If necessary for pre-ata
drives, it can be waited for later (we got it wrong by only looking
at it for drive 0 anyway). It is set as part of a historical
signature for ata drives but doesn't say anything useful about the
reset state. It is cleared as part of a non-historical signature
for atapi drives so that drivers which don't understand atapi drives
seem to see no drive. Waiting for it caused lengthy delays and
broke the status returned by wdreset() in cases where the master
was not an ata drive. Then the whole wdprobe() failed in some
cases where the recovery code didn't work.
Don't wait for drive ready in wdreset(). The considerations are
the same as for seek complete, except drive ready does say something
useful about the reset state of ata drives, and waiting for it
later is required anyway for such drives.
Lengthy delays can now be avoided by not configuring nonexistent
(ata) drives. Unfortunately, this breaks detection of atapi drives
in some configurations.
switching video modes. People typically see the panic when the screen
saver has been running and is being stopped.
WARNING: this is not a real fix. Something really funny must be
happening in the page table entries for the physical memory
0x0-0xa0000, which is mapped to the beginning of the kernel region.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
driver was thinking irq was enabled although it wasn't.
This case was particular to a no-interrupt static configuration.
Reported by: "Norman C. Rice" <nrice@emu.sourcee.com>
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
structures" but since tty structs aren't malloced it is actually
mainly for tty-level (clist) buffers. It was slightly misused
here for com structs, and the previous commit completely misused
it for device buffers.
Fixed some bugs in nearby pccard code:
- memory leak when pccards go away (broken in previous commit).
- bogus bzeroing of the com struct before freeing it.
- style bugs.
the input speed, so that it can work at speeds larger than 115200
bps without being flow controlled. The buffer is twice as large
as before at 115200 bps and half as large as before at low speeds
Use a single interrupt-level buffer instead of ping-pong buffers
because the simplifications provided by ping-pong buffers became
complications.
This change is over-engineered. Statically configured buffering
was simpler and faster, and increasing the buffer size to support
1.5Mbps would cost about 1 US cent's worth of RAM per port, but I
was interested in the buffer switching mechanism.
Increase the overall length of the delay by 10.
Without this a 3C509 card on my MediaGX crash box can't be reliably
read. With this it is solid.
I've left a delay multiplier in instead of just changing the base
delay because I'm surprised I had to increase it so much and expect
there may be another problem.
Change microseq offsets. Previously, offsets of the program counter where
added to the index of the current microinstruction. Make them rely on the
index of the next executed microinstruction.
Suggested by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
also a bit of a BDE patch in there I beleive. Backs out a fix I needed for Cyrix support
early on but it turns out that a later fix in the cyrix support made it un-needed.
