most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
for the particular card in use. At the moment, I've set it to any of
the bt445S VLB cards (not the bt445C which apparently work) and the
bt5xx series (isa cards). The 742 and PCI cards should not need it. :-)
It may be useful to have something like this:
#ifndef BOUNCE_BUFFERS
if (bounce_buffers_required && more_than_16MB_ram)
panic("this card requires bounce buffers for more than 16MB ram!")
#endif
to get the definitions of TRUE and FALSE which happen to be defined in
a deeply nested include.
Added nearby #includes of <sys/conf.h> where appropriate.
is not real helpful since swapgeneric.c doesn't seem to be used, except
perhaps on a GENERIC kernel. (Sorry Paul.. :-)
I've moved it from swapgeneric.c to autoconf.c, since autoconf.c also deals
with dumpdev things. There may be a better place.....
but probably harmless. It's hard to tell because apparently no one runs
ity.
Fixed ity's d_reset entry. `nx' entries should never be used for existing
devices.
conf.c:
Moved a prototype to a better place.
Removed a stale #define.
sscselect(). Use the standard dummies nostrategy(), noread(),
nowrite() and noselect() instead.
sscread() and sscwrite() returned bogus errnos. It isn't possible
to return an error from a select routine so noselect() is just as
bogus as sscselect() (it's equivalent to nullselect()).
Fixed two cases of "=" that should have been "==" in card type comparison.
Simplified expression that checks for interface up/down.
Moved ed_ring_copy to before its first use so that it's inlined as intended.
Change mbuf allocation policy so that a received packet is stored in just
an mbuf header (no cluster) if it will fit in one.
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
Move a lot of variables home to their own code (In good time before xmas :-)
Introduce the string descrition of format.
Add a couple more functions to poke into these marvels, while I try to
decide what the correct interface should look like.
Next is adding vars on the fly, and sysctl looking at them too.
Removed a tine bit of defunct and #ifdefed notused code in swapgeneric.
Protected them with `#ifdef KERNEL' so that <sys/queue.h> is valid C++.
Added the necessary #includes of <sys/queue.h>.
These functions are bogus and should be replaced by the queue macros.
but also IT ACTUALLY WORKS!
FreeBSD with options JREMOD now runs with no entries in the devsw tables
prior to the devices puting their own entries there..
Thanks to bde and terry for thoughts and comments.
next stop 'Real' devfs support in devices.
- Don't print out meaningless iCOMP numbers, those are for droids.
- Use a shorter wait to determine clock rate to avoid deficiencies
in DELAY().
- Use a fixed-point representation with 8 bits of fraction to store
the rate and rationalize the variable name. It would be
possible to use even more fraction if it turns out to be
worthwhile (I rather doubt it).
The question of source code arrangement remains unaddressed.
conflicted with S3 graphics cards. Now users should put sio[2-3]
in the config file if the hardware exisst, even if the probe is
certain to fail due to an interrupt conflict. Otherwise, ports
sharing the interrupt may fail the probe if the system is warm
booted while sio[2-3] are active (perhaps under another OS). The
same problem for nonstandard ports is now handled better than
before.
add a few safety checks in specfs because
now it's possible to get entries in [cd]devsw[] which are ALL NULL
so it's better to discover this BEFORE jumping into the d_open() entry..
more check to come later.. this getsthe code to the stage where I
can start testing it, even if I haven't caught every little error case...
I guess I'll find them quick enough..
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
