time we tell CAM to rescan the bus. Together with the previous patch
this should avoid the problem where the devices would wedge because they
got spoken to over two different pipes.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
attachment after boot in some cases where the device gets confused if
spoken to over two different pipes simultaneously (resulting in TIMEOUT
errors on requesting INQUIRY data).
This solution is far from perfect, as after umass_attach has returned
the USB stack fetches the string descriptors in order for creating the
event that is sent to userland. It just makes the chances of collisions
less likely.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
the UFI command set. Even with this patch, it's incredibly slow on my
laptop, but at least now it works.
Note that the drive is reported to CAM with the vendor and device IDs from
the device itself, forcing the user to patch the da(4) quirk table
manually.
signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Add the entry for the Yano U640MO-03 MO drive. (ifdef-0-ed out for now)
Fix a hack were an original buffer was modified instead of copied
(cmd[] -> (*rcmd)[])
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
instead of the requested length. Otherwise all transfers look like 0 byte
transfers to CAM.
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
2) Finalise the command in the case of CBI transfers with CCI (command
completion interrupt).
3) Remove a redundant bzero of a buffer.
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
from the SCSI id it has. (this avoids the confusing umass-sim32 device. It
should have been umass-sim0 all along (there is only one), and if it is
spoken to as a SCSI device the sim should be umass32.
Make the rescan actually work. We need to fill in a target and lun wildcard
and not the SCSI id of the SIM.
Add a seatbelt.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
