we start turning any of them back on again. This works around a bug in
some BIOSen that alias two different link devices for APIC vs ATPIC modes
onto the same physical hardware link.
Submitted by: njl
Tested by: Antoine Brodin antoine dot brodin at laposte dot net
systems that boot with this value at the lowest setting. Change the
default boot config back to "leave frequency as BIOS set it". Also, fix
buglet where acpi_throttle wouldn't be used if p4tcc was present but
disabled by the user.
MFC after: 1 week
to see what features they may support before calling identify/probe/attach.
This is necessary because the ACPI 3.0 spec requires driver support be
advertised before running any methods. For now, the flags are as specified
in for the _PDC and _OSC methods but we can support private flags as needed.
Add an implementation of this for acpi_cpu. It checks all its children
(notably cpufreq drivers) and calls the _PDC method to report the results.
acpi_bus_alloc_gas() to delete the resource it set if alloc fails. Then,
change acpi_perf to delete the resource after releasing it if alloc fails.
This should make probe and attach both fully restartable if either fails.
may help with various interdependencies between subsystems. More testing
is needed to understand what the underlying issues are here.
Tested by: Juho Vuori
MFC after: 2 days
count of valid frequencies and use that as the final package count, don't
give up when the first invalid state is found. Also, add 0x9999 and expand
our upper check to >= 0xffff Mhz [2].
Submitted by: Bruno Ducrot, Jung-uk Kim [2]
(like an EC/SMbus controller) to access the EC address space. Access
is synchronized by the EcLock/Unlock routines in EcSpaceHandler().
Tested by: Hans Petter Selasky
same value as the previous ioctls so no binary change. Also, make a few
style changes to reduce diffs to my tree.
Loosely based on code from: Hans Petter Selasky
- Fix a bug in the same condition where we forgot to drop the ACPI pcib
lock. This fixes hangs after the pcib0 attach on some machines.
Tested by: sos (2)
modulating the STPCLK# pin based on the duty cycle. Since p4tcc uses the
same mechanism (but internal to the CPU), we triggered a hang on some
systems at low frequencies when both were in use. Now, disable
acpi_throttle when p4tcc is also present.
Tested by: Kevin Oberman
SMP systems. It appears all drivers except ichss should attach to each
CPU and that settings should be performed on each CPU. Add comments about
this. Also, add a guard for p4tcc's identify method being called more than
once.
IRQ 0 and not an ExtINT pin. The MADT enumerators ignore the PC-AT flag
and ignore overrides that map IRQ 0 to pin 2 when this quirk is present.
- Add a block comment above the quirks to document each quirk so that we
can use more verbose descriptions quirks.
MFC after: 2 weeks
modes, systems may take longer. If the status values don't match, try
matching just the lowest 8 bits if no bits above 8 are set in the desired
value. The IBM R32 has other bits set in the status register that are
irrelevant to the expected value.
the switch. Other interim tests (i.e., for minimum runtime) could
invalidate the start time. This fixes transitions to cooler states in that
now they go to the next active state (_AC0 -> _AC1) instead of going
straight to off (_AC0 -> off).
Submitted by: Alexandre "Sunny" Kovalenko (Alex.Kovalenko / verizon.net)
locks held, specify the ACPI_ISR flag to keep it from acquiring any more
mutexes (which could potentially sleep.) This should fix "could sleep"
warning messages on the following path:
msleep()
AcpiOsWaitSemaphore()
AcpiUtAcquireMutex()
AcpiDisableGpe()
EcGpeHandler()
AcpiEvGpeDispatch()
AcpiEvGpeDetect()
AcpiEvGpeDetect()
AcpiEvSciXruptHandler()
driver. This used to be handled by cpufreq_drv_settings() but it's
useful to get the type/flags separately from getting the settings.
(For example, you don't have to pass an array of cf_setting just to find
the driver type.)
Use this new method in our in-tree drivers to detect reliably if acpi_perf
is present and owns the hardware. This simplifies logic in drivers as well
as fixing a bug introduced in my last commit where too many drivers attached.
are not added to the list(s) of available settings. However, other drivers
can call the CPUFREQ_DRV_SETTINGS() method on those devices directly to
get info about available settings.
Update the acpi_perf(4) driver to use this flag in the presence of
"functional fixed hardware." Thus, future drivers like Powernow can
query acpi_perf for platform info but perform frequency transitions
themselves.
throttling, neglecting to do this kept the sysctls from appearing.
Attach an acpi_throttle device to each CPU that supports it.
Don't add a device if the P_BLK is invalid or if _PTC is not present.
This removes extraneous probe/attach failure messages on some machines.
Make the cpu throttle state local to the softc to account for partial
successes when changing the clock rate on MP machines.
doing it in the cpu driver. The previous code was incorrect anyway since
this value controls Px states, not throttling as the comment said. Since
we didn't support Px states before, there was no impact. Also, note that
we delay the write to SMI_CMD until after booting is complete since it
sometimes triggers a change in the frequency and we want to have all
drivers ready to detect/handle this.
devclass. As pointed out by dfr@, devclasses don't have to share the same
linkage if multiple drivers have the same name. Newbus should match the
devclasses based on name and allocate non-conflicting unit numbers.
the PERF_CTRL register in our probe method so that we can tell earlier
that another driver should handle this device due to FFixedHW. This avoids
scaring users when attach failed when we really wanted probe to fail.
