change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
Because nfe(4) hardware doesn't support SG on Rx path, supporting
jumbo frame requires very large contiguous kernel memory(i.e. several
mega bytes). In case of lack of contiguous kernel memory that
allocation request may always fail. However nfe(4) can operate on normal
sized MTU frames, so go ahead and just disable jumbo frame support.
While I'm here add a new tunable "hw.nfe.jumbo_disable" to disable
jumbo frame support.
In nfe_poll, make sure to invoke correct Rx handler.
Approved by: re (kensmith)
MCLBYTES for the segment size but it used too many Tx descriptors in
TSO case.
While I'm here adjust maximum size of the sum of all segment lengths
in a given DMA mapping to 65535, the maximum size, in bytes, of a IP
packet.
o s/printf/device_printf/g
o Nuke OpenBSDism.
o Nuke NetBSD/OpenBSD specific DMA sync operations.(we don't have a way
to sync a single descriptor within a DMA map.)
o Remove recursive mutex.
o bus_dma(9) clean up.
o 40bit DMA address support.
o Add protection for Rx map load failure.
o Fix a long standing bug for watchdog timeout. [1]
o Add additional protections, missing Tx completion interrupt, losing
start Tx command, for watchdog timeout.
o Switch to taskqueue(9) API to handle interrupts.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Advertise VLAN header length/capability correctly to upper layer.
o Remove excessive kernel stack consumption in nfe_encap().
o Handle highly fragmented mbuf chains correctly.
o Enable etherenet address reprogramming with ifconfig(8).
o Add ALTQ/TSO, MSI/MSIX support.
o Increased Rx ring to 256 descriptors from 128.
o Align Tx/Rx descriptor ring on sizeof(struct nfe_desc64) boundary.
o Remove alignment restrictions on Tx/Rx buffers.
o Rewritten jumbo frame support code.
o Add support for hardware assistend VLAN tag insertion/stripping.
o Add support for Tx/Rx flow control based on patches from Peer Chen. [2]
o Add a routine that detects whether ethernet address swap routines is
required. [3]
o Add a workaround that take MAC/PHY out of power down mode.
o Add suspend/resume support.
o style(9) and code clean up.
Special thanks to Shigeaki Tagashira, the original porter of nfe(4),
who submitted lots of patches, performed uncountable number of
regression tests and maintained nfe(4) for a long time. Without his
enthusiastic help and support I could never have completed this
overhauling task.
The only weak point of nfe(4) compared to nve(4) is instability of
manual half-duplex media selection on certain hardwares(auto sensing
media type should work for all cases, though). This was a long
standing bug of nfe(4) and I still have no idea why it doesn't work
on some hardwares.
Obtained from: OpenBSD [1]
Submitted by: Peer Chen < pchen at nvidia dot com > [2], [3]
Reviewed by: Shigeaki Tagashira < shigeaki AT se DOT hiroshima-u DOT ac DOT jp >
Tested by: Shigeaki Tagashira, current
Discussed with: current
Silence from: obrien
If these drivers are setting M_VLANTAG because they are stripping the
layer 2 802.1Q headers, then they need to be re-inserting them so any
bpf(4) peers can properly decode them.
It should be noted that this is compiled tested only.
MFC after: 3 weeks
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
i386 (I don't know) but on amd64 at hand here, it paniced early at
boot.
(I'm pretty sure that PAGE_SIZE here was miscopied from another place
during porting, where in OpenBSD bus_dmamem_alloc() is used, but there
PAGE_SIZE means completely different thing.)
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
