o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
machine arm
device mem
options GEOM_BSD
options GEOM_MBR
Remove the first two from all kernel configuration files and
change geom_bsd and geom_mbr from standard to optional.
FreeBSD 8-CURRENT was tested and run successfully on the following eval
boards and devices :
* DB-88F5182, DB-88F5281 (Orion based)
* DB-88F6281, RD-88F6281 (Kirkwood based)
* DB-78100 (Discovery based)
For more detailed info on build instructions and other examples please refer
to http://wiki.freebsd.org/FreeBSDMarvell
Obtained from: Marvell, Semihalf
don't inline the locking primitives, and only grab those parts of mii
that we really need. Other space optimizations are too agressive for
the generic file (removing all of usb, and loading it as kernel
modules).
o It has been tested only on KB9202, KB9202A and KB9202B boards
o Better comments about hints
o option<space><tab>
o Add newer SX_NOINLINE option.
o Fix a few comments
As clearly mentioned on the mailing lists, there is a list of drivers
that have not been ported to the MPSAFE TTY layer yet. Remove them from
the kernel configuration files. This means people can now still use
these drivers if they explicitly put them in their kernel configuration
file, which is good.
People should keep in mind that after August 10, these drivers will not
work anymore. Even though owners of the hardware are capable of getting
these drivers working again, I will see if I can at least get them to a
compilable state (if time permits).
don't support the ioapic either, so remove that option too. These
were commented out, but could never be enabled, unlike the other
options in the file that are commented out.
boards. This is enough to net-boot to multiuser.
Also supported is the SMSC LAN91C111 parts used on the netCF, netDUO and netMMC
add-on boards.
I'll be putting some instructions on how to boot this on the Gumstix boards
online soon.
This is still fairly rough and will be refined over time but I felt it was
better to get this out there where other people can help out.
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
to detect (or load) kernel NLM support in rpc.lockd. Remove the '-k'
option to rpc.lockd and make kernel NLM the default. A user can still
force the use of the old user NLM by building a kernel without NFSLOCKD
and/or removing the nfslockd.ko module.
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
only USB 1.1 speeds available, but this shouldn't hurt. Now that we have
working usb support for this board, this is a natural followup.
Approved by: re (kensmith)
FreeBSD/arm installworld install is only 170MB. The smallest SD card
I could find at the store today was 512MB (and it was only $10 after
rebate), with a 2GB card for as low as $25.00...
Now that the IIC stuff has been sorted out, include that as well.
Include hints for the icee 16kb 16-bit i2c device. It should include
info about the temperature sensor as well, but that driver isn't quite
ready.
Add bpf for dhclient happiness.
MFC After: 1 week
mapped at, and LOADERRAMADDR, the address at which the loader maps the ram at
at the time the kernel is booted.
They are used to detect if the kernel is booted from the onboard flash.
Define those for the IQ31244
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
The 'nooption' kernel config entry has to be used to turn KSE off now.
This isn't my preferred way of dealing with this, but I'll defer to
scottl's experience with the io/mem kernel option change and the grief
experienced over that.
Submitted by: scottl@
an explicit comment that it's needed for the linuxolator. This is not the
case anymore. For all other architectures there was only a "KEEP THIS".
I'm (and other people too) running a COMPAT_43-less kernel since it's not
necessary anymore for the linuxolator. Roman is running such a kernel for a
for longer time. No problems so far. And I doubt other (newer than ia32
or alpha) architectures really depend on it.
This may result in a small performance increase for some workloads.
If the removal of COMPAT_43 results in a not working program, please
recompile it and all dependencies and try again before reporting a
problem.
The only place where COMPAT_43 is needed (as in: does not compile without
it) is in the (outdated/not usable since too old) svr4 code.
Note: this does not remove the COMPAT_43TTY option.
Nagging by: rdivacky
