bus_generic_resume() since the pci_link(4) driver was added.
- Change the ACPI PCI-PCI bridge driver to inherit most of its methods
from the generic PCI-PCI bridge driver. In particular, this will now
restore PCI config registers for ACPI PCI-PCI bridges.
Tested by: Oleg Sharoyko osharoiko of gmail
infrastructure, not us. This appears to be a leftover from an older
version of the driver.
Submitted by: avg
Tested by: Anton Shterenlikht <mexas bristol.ac.uk>
MFC after: 1 week
X-MFC-Note: To stable/8 and stable/7 only
This way we would have an opportunity to hide the
Tj(target) value doesn't seem right stuff if we know
it's not working there.
Add temperature value for Core2 Duo Extreme Mobile that
I have access to.
Xeon 5500/5600 series:
- Utilize IA32_TEMPERATURE_TARGET, a.k.a. Tj(target) in place
of Tj(max) when a sane value is available, as documented
in Intel whitepaper "CPU Monitoring With DTS/PECI"; (By sane
value we mean 70C - 100C for now);
- Print the probe results when booting verbose;
- Replace cpu_mask with cpu_stepping;
- Use CPUID_* macros instead of rolling our own.
Approved by: rpaulo
MFC after: 1 month
a PMC. It was possible that we could have turned a bit on but
never cleared it.
Extend the calls to rdmsr() to all necessary functions, not
just those which previously caused a panic.
Pointed out by: jhb@
MFC after: 1 week
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
plug. Note that the Vendor ID 0x04b4 is officially assigned to Cypress,
so use that instead of adding a second vendor with an identical ID, in the
same way other similar cases are treated in usb/usbdevs.
PR: usb/132785
Submitted by: Dirk-Willem van Gulik <dirkx webweaving.org>
MFC after: 1 week
10G cards. 1G cards are x4 only.
- Use constants from pcireg.h for reading the current link width.
- Use pci_set_max_read_req() rather than implementing it by hand.
Reviewed by: np
MFC after: 1 week
This is similar to a fix in r189305 but for earlier ICH versions (<= 5).
Reported by: someone via attilio
Discussed with: des, attilio
MFC after: 1 week
tail pointers of the tx and rx queues. We needed a SYSCTL_PROC
to correctly get the values at run time.
Submitted by: Andrew Boyer aboyer at averesystems.com
MFC after: 1 week
This version adds support for ARC1880; additionally this version fixed
an issue where all devices on a SAS port gets offlined when any device
failed on the port [1].
Many thanks to Areca for continuing to support FreeBSD.
PR: kern/148502 [1]
Submitted by: Ching-Lung Huang <ching2048 areca com tw>
Obtained from: Areca
Tested by: Rich Ercolani <rercola acm jhu edu> [1]
MFC after: 2 weeks
lengths. Make MI wrapper code to validate periods in request. Make kernel
clock management code to honor these hardware limitations while choosing hz,
stathz and profhz values.
- Fixed the interface probe routine to only attach to USB interfaces the driver
actually supports. This allows other drivers to attach to things like
MicroSD slots etc.
- Fixed network interface enumeration to be globally sequential instead of
relying on the USB interface numbers. This make sure the first network
interface always is at uhso0 and the second at usho1 and so on.
- Added a radio kill switch; exposed through sysctl.
- Updated the manual page to be verbose about the number of serial ports and
include iCON 452 in the set of tested hardware.
Submitted by: Fredrik Lindberg
calls. Also add BUS_DMA_COHERENT flag to bus_dmamem_alloc(9) to
take advantage of efficient synchronization for architectures that
support that feature.
Reviewed by: davidch
return code. If context was not setup correctly give up
initialization. While I'm here move variable declarations to the
beginning of the function.
Reviewed by: davidch
