by removing unsued file local functions and then unused callees.
A lot more warnings to resolve but someone had to break the ice.
MFC after: 10 days
X-Comment: I am not the new maintainer; chime in, it's ours.
o Forward termianl framebuffer ioctl to fbd.
o Forward terminal mmap request to fbd.
o Move inclusion of sys/conf.h to vt.h.
Sponsored by: The FreeBSD Foundation
The priority goes from "error" to "debug".
Connectors are polled every 10 seconds. Reading EDID is part of this
polling. However, when an invalid EDID is returned, this error message
is logged. When using Newcons for instance, having a kernel message
every 10 seconds is getting annoying.
Now that it's a debug message, it'll be logged only if hw.dri.debug is
enabled. This fix console spamming for some users.
Tested by: Larry Rosenman <ler@lerctr.org>
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
... for msleep/cv_*wait() return values, where wait_event*() is used
on Linux. ERESTARTSYS is the return code expected by callers when the
operation was interrupted.
For instance, this is the case of radeon_cs_ioctl() (radeon_cs.c): if
an error occurs, and the code isn't ERESTARTSYS (eg. EINTR), it logs an
error.
Note that ERESTARTSYS is defined as ERESTART, but this keeps callers'
code close to Linux.
Submitted by: avg@ (previous version)
Normal and bold fonts each have a glyph map for single or left half-
glyphs, and right half glyphs. The flag TF_CJK_RIGHT in term_char_t
requests the right half-glyph.
Reviewed by: ed@
Sponsored by: The FreeBSD Foundation
The previous code was checking the "VGA Enable" bit on the video card's
parent PCI-to-PCI bridge only. This didn't work for the case where the
video card is attached to the root PCI bus (ie. the card has no parent
PCI-to-PCI bridge).
Now, the new code:
1. checks the "VGA Enable" bit on the parent bridge only if it's a
PCI-to-PCI bridge;
2. always checks the "I/O" and "Memory address space decoding" bits
on the video card itself.
However, vendor-specific bits are not used.
This fixes the use of many integrated Radeon cards: without this patch,
we fail to detect them as the boot display and, when radeonkms looks for
the Video BIOS, it skips the shadow copy made by the System BIOS. It
then fails to fully initialize the card, because the shadow copy is the
only way to read the Video BIOS in these situations. A workaround was to
force the boot display selection using the "hw.pci.default_vgapci_unit"
tunable.
A previous version of this patch added a new function doing the checks.
Now, the vga_pci_is_boot_display() function is used to perform the
checks (only until the boot display is found) and return if the given
device is the boot display or not.
Furthermore, vga_pci_attach() logs "Boot video device" if the card being
attached it the Chosen One:
vgapci0: <VGA-compatible display> [...]
vgapci0: Boot video device
Reviewed by: kib@, jhb@ (both a previous version)
Tested by: lunatic_ (#freebsd-xorg, integrated Radeon card,
xmj (#freebsd-xorg, i915+NVIDIA cards)
Introduce a new formatting bit (TF_CJK_RIGHT) that is set when putting a
cell that is the right part of a CJK fullwidth character. This will
allow drivers like vt(9) to support fullwidth characters properly.
emaste@ has a patch to extend vt(9)'s font handling to increase the
number of Unicode -> glyph maps from 2 ({normal,bold)} to 4
({normal,bold} x {left,right}). This will need to use this formatting
bit to determine whether to draw the left or right glyph.
Reviewed by: emaste
using cpuid can be quirky (this is the case of VMWare without the
vPMC support) but fail to probe hwpmc.
o Apply the fix for XEON family of processors as established by
315338-020 document (bug AJ85).
Sponsored by: EMC / Isilon storage division
Reviewed by: fabient
Previously the code would just iterate over the whole tree as if it were
just a list.
Without this change I would observe X server becoming more and more
jerky over time.
MFC after: 5 days
in6addr_any and is not in the CLIP table either. This fixes a reported
TOE+IPv6 NULL-dereference panic in do_pass_open_rpl().
While here, stop creating hardware servers for any loopback address.
It's just a waste of server tids.
MFC after: 1 week
Some Intel XHCI controlles timeout processing so-called "TRBs" when
the final LINK TRB of a so-called "TD" has the CHAIN-BIT set.
MFC after: 1 week
Tested by: glebius @
