dev.bce.<unit>.nvram_dump
Add the capability to write the complete contents of the NVRAM via sysctl
dev.bce.<unit>.nvram_write
These are only available if the kernel option BCE_DEBUG is enabled.
The nvram_write sysctl also requires the kernel option
BCE_NVRAM_WRITE_SUPPORT to be enabled. These are to be used at your
own caution. Since the MAC addresses are stored in the NVRAM, if you
dump one NIC and restore it on another NIC the destination NIC's
MAC addresses will not be preserved. A tool can be made using these
sysctl's to manage the on-chip firmware.
Reviewed by: davidch, yongari
BGE_MI_MODE register accesses. Previously bge(4) used to read
BGE_MI_MODE register to detect whether it needs to disable
autopolling feature or not. Because we don't touch autopolling in
other part of driver there is no reason to read BGE_MI_MODE
register given that we know default value in advance. In order to
achieve the goal, check whether the controller has CPMU(Central
Power Mangement Unit) capability. If controller has CPMU feature,
use 500KHz MII management interface(mdio/mdc) frequency regardless
core clock frequency. Otherwise use default MII clock. While I'm
here, add CPMU register definition.
In bge_miibus_readreg(), rearrange code a bit and remove goto
statement. In bge_miibus_writereg(), make sure to restore
autopolling even if MII write failed. The delay time inserted after
accessing BGE_MI_MODE register increased from 40us to 80us.
The default PHY address is now stored in softc. All PHYs supported
by bge(4) currently uses PHY address 1 but it will be changed when
we add newer controllers. This change will make it easier to change
default PHY address depending on PHY models.
Submitted by: davidch
physical address. Adds a dma tag to the XLR/XLS pci bus with the
lowaddr if the CPU happens to be a XLR C rev.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro dot com))
special eject command to reappear as modem. It also requires DIR_IN flag
in the command message, so we supply some dummy data along with the command.
Feedback from X080S owners appreciated. I have not a pure Alcatel/TCTMobile
device, but another one under "Svyaznoy" (Связной) brand, and I didn't yet
managed to get it working. It is successfully recognized, it responds to
AT commands, but it shuts up right after successfull CONNECT response.
Reviewed by: hps
- nlge_ioctl handles IFF_UP and IFF_PROMISC flags
- Translate table code, to enable flow based CPU assignment added
disabled by default (can be enabled by a tunable).
- Changed signature of nlge_port_disable to make it consistent with nlge_port_enable
- Removed TXCSUM and VLAN_HW_TAGGING from i/f capabilities.
Submitted by: Sriram Gorti (srgorti at netlogicmicro dot com)
also in the base set, the man utility when invoked with -a would display
pages for each locale in the same tree:
$ LANG=en_GB.ISO8859-15 man -wa man
/usr/share/man/en.ISO8859-15/man1/man.1.gz
/usr/share/man/man1/man.1.gz
/usr/share/man/en.ISO8859-15/man7/man.7.gz
/usr/share/man/man7/man.7.gz
Use continue to break out of the loop for the current locale. This results
in behavior more closely matching the old GNU man implementation:
$ LANG=en_GB.ISO8859-15 man -wa man
/usr/share/man/en.ISO8859-15/man1/man.1.gz
/usr/share/man/en.ISO8859-15/man7/man.7.gz
This will still search for a copy of the file in other manual path
locations. If there was a /usr/local/man/man1/man.1.gz file, it would still
be displayed. This is also consistent with the GNU man implementation.
Submitted by: arundel
Approved by: wes (mentor implicit)
values to zero. A correct solution would involve emulating vector
operations on denormalized values, but this has little effect on accuracy
and is much less complicated for now.
MFC after: 2 weeks
pmap_kextract()) before pmap_bootstrap() is called.
Document the set of pmap functions that may be called before
pmap_bootstrap() is called.
Tested by: bde@
Reviewed by: kib@
Discussed with: jhb@
MFC after: 6 weeks
sysctl and counters for message ring threads (intial version). Update
watermark values, and and decrease the maximum threads to 3 (this will leave
a few CPUs for other processes)
Minor comment fix in nlge.
successfully received a frame but we failed to pass it to upper
stack due to lack of resources. So update if_iqdrops counter
instead of updating if_ierrors counter.
mode in the USB core. The patch mostly consists of updating the USB
HUB code to support USB 3.0 HUBs. This patch also add some more USB
controller methods to support more active-alike USB controllers like
the XHCI which needs to be informed about various device state events.
USB 3.0 HUBs are not tested yet, due to lack of hardware, but are
believed to work.
After this update the initial device descriptor is only read twice
when we know that the bMaxPacketSize is too small for a single packet
transfer of this descriptor.
Approved by: thompsa (mentor)
