PCPU fields for curthread, by doing the same to Book-E. This closes
some potential races switching between CPUs. As a side effect, it turns out
the AIM and Book-E swtch.S implementations were the same to within a few
registers, so move that to powerpc/powerpc.
MFC after: 3 months
This fixes fallout from r256425.
Reported by: Pavel Timofeev <timp87@gmail com>
Tested by: Pavel Timofeev <timp87@gmail com>
Reviewed by: Roger Pau Monnц╘
MFC after: 3 days
add actual platform probing based on PVR. Still needs a little more work:
in particular, the CCRS setup should move here.
Also turn "bare" into a truly bare platform that doesn't pretend to know how
to do anything except get the memory map. This should also be enhanced to
process the FDT reserved memory list, but that is for another day.
assumed that the MDIO bus was a direct child of the Ethernet interface. It
may not be and indeed on many device trees is not. While here, add proper
locking for MII transactions, which may be on a bus shared by several MACs.
Hardware donated by: Benjamin Perrault
unlocked route. Use in6_rtalloc() instead of in6_rtalloc1. This helps
simplify the code and remove several now unused variables.
PR: 156283
MFC after: 2 weeks
NIC and pushed up to the driver. Unfortunately this means there's
no rate control notification done. Thus, if the rate control code
makes a decision that hits a crappy rate that can't succeed, the
rate code would never lower the rate and packet loss would continue.
So, fake some rate control notification in this case.
Without this, a far away station with low signal strength would
associate using the management rate (by default the lowest rate)
and then the EAPOL frames would go out at the current AMRR best
guess. This would result in association failing authentication.
Tested:
* Intel 5100, STA
* Intel 2230, STA
- Process ATIO queue only if interrupt status tells so;
- Do not update queue out pointers after each processed command, do it
only once at the end of the loop.
every time. The purpose of that register is unlikely output queue overflow
detection, so read it only when its last known (and probably stale now)
value signals overflow.
This reduces CPU load and lock congestion and rises bottleneck in CTL
while doing target mode via two 8Gbps ports from 100K to 120K IOPS.
- Fix LOR and possible lock recursion when handling high-power commands.
Introduce new lock to protect left power quota and list of frozen devices.
- Correct locking around xpt periph creation.
- Remove seems never used XPT_FLAG_OPEN xpt periph flag.
_KERNEL braces. Struct mount is only defined for the kernel build.
Reported and tested by: andreast
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
The hang occurred in nfsv4_setsequence() when it couldn't find an
available session slot and is fixed by checking for a forced dismount
in progress and just returning for this case.
MFC after: 1 month
shared vnode lock for VOP_PUTPAGES() as well. The only such
filesystem in the tree is ZFS, and it uses
vnode_pager_generic_putpages(), which performs the pageout with
VOP_WRITE().
Reviewed by: alc
Discussed with: avg
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
holding the vnode lock; vp->v_mount is checked first for NULL
equiality, and then dereferenced if not NULL. If vnode is reclaimed
meantime, second dereference would still give NULL. Change
VFS_PROLOGUE() to evaluate the mp once, convert MNTK_SHARED_WRITES and
MNTK_EXTENDED_SHARED tests into inline functions.
Reviewed by: alc
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
There were two bugs:
* If the initial lowest rate didn't go through the loop at least once,
the AMRR rate index would be the highest rate in the table
(eg the rix mapping to MCS15) but rate would stay at the default
value, namely 0.
This meant that the initial rate selection would be MCS15 _but_ the
node ni_txrate value would be MCS0.
* If the node is 11n, then break out of the loop correctly. Beforehand,
my initial 11n AMRR commit would immediately exit out as it would
fail the 11n check, then it would always fall through to the non-11n
rate which would then see if it was < 36mbit (ie, "72"), which would
always match. Hence, it'd always return MCS15.
Tested:
* Intel Centrino 2230 STA (local changes), STA mode
* Intel Wifi 5100, STA
This is a no-op for now!
* Add a new flag value for "there are no extra bits" for some random
field;
* Add a definition for the maximum number of calibration entries in
the calibration data cache in iwn_softc. It's not yet used.
* Add regulatory bands for the 2030 NIC.
Submitted by: Cedric Gross <cg@cgross.info>
makes FreeBSD halt but not poweroff (as expected when issuing a
shutdown from the VM manager). Fix this by using the same handler
for both "halt" and "poweroff".
NB: The "halt" signal seems to be used on XenServer only. The OSS
Xen toolstack (xl) uses "poweroff" instead.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
MFC after: 2 days
