r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
Make completion event path mostly lockless using EPOCH(9).
Implement a mechanism using EPOCH(9) which allows us to make
the callback path for completion events mostly lockless.
Simplify draining callback events using epoch_wait().
While at it make sure all receive completion callbacks are
covered by the network EPOCH(9), because this is required
when calling if_input() and ether_input() after r357012.
Sponsored by: Mellanox Technologies
The hardware offload is primarily targeted for TLS v1.2 and v1.3,
using AES 128/256 bit pre-shared keys. This patch adds all the needed
hardware structures, capabilites and firmware commands.
Sponsored by: Mellanox Technologies
The PRM suggests random 0 - 10ms to prevent multiple waiters on the same
interval in order to avoid starvation.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Linux commits:
6c780a0267b8
b8a92577f4be.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5core. The EEPROM information is not only a property of the
mlx5en(4) driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
All prints in mlx5core should use on of the macros:
mlx5_core_err/dbg/warn
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
In case of health counter fails to increment it indicates a bad device health.
In case when the syndrome indicated by firmware is 0x0, this indicates that
firmware is unable to respond to initialization segment reads.
Add proper print in this case.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MPFS is a logical switch in the Mellanox device which forward packets
based on a hardware driven L2 address table, to one or more physical-
or virtual- functions. The physical- or virtual- function is required
to tell the MPFS by using the MPFS firmware commands, which unicast
MAC addresses it is requesting from the physical port's traffic.
Broadcast and multicast traffic however, is copied to all listening
physical- and virtual- functions and does not need a rule in the MPFS
switching table.
Linux commit: eeb66cdb682678bfd1f02a4547e3649b38ffea7e
MFC after: 3 days
Sponsored by: Mellanox Technologies
There is no reason to re-create the command workqueue during healthcare.
This also fixes an issue where a previous work struct may refer to a
destroyed workqueue.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Present code uses lock-less accesses to the dump data to prevent top
level ioctls from blocking bottom-level call to dump. Unfortunately, this
depends on the type stability of the dump data structure, which makes it
non-functional during driver teardown.
Switch to the mutex locking scheme where top levels use the mutex in the
bound regions, while copyouts and drain for completion utilize condvars.
The mutex lifetime is guaranteed to be strictly larger than the time
interval where driver can initiate dump, and most of the control fields
of the old struct mlx5_dump_data are directly embedded into struct
mlx5_core_dev.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid race for command completion when triggering a command completions event.
Serialize operation by queueing all commands on the same work queue.
This can happen when healthcare triggers.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Implement a watchdog as part of the healtcare subsystem which
reads the PCI power status during startup and upon the PCI
power status change event and store it into the core device
structure. This value is then exported to user-space via a
read-only SYSCTL. A dmesg print has been added to inform
the admin about the PCI power status.
MFC after: 3 days
Sponsored by: Mellanox Technologies
