limit the number of outstanding requests on a specific drive and
overall.
Change the way we set the active request count. This enables us to
start the requests without being in splbio for the duration, which
could be very long for IDE drives in PIO mode.
context. Be prepared to fail instead.
MMalloc, FFree: ensure that saved file names are properly terminated.
Use MCFILENAMELEN instead of the previous explicit constant.
and then doing it itself, resulting in a panic downed drives.
Sleuth-work-by: Christopher Masto <chris@netmonger.net>
Remove dummy function initsd, which is now (implemented) in
vinumrevive.c
vinum_scandisk: Check that a drive is up before reading from it. This
is probably excessive paranoia.
same interface as Intel's P6 family has. Incidentally, I had disabled
it in the first place since I knew the K7s were coming out soon but
did not want to assume they'd have the same MTRR interface as Intel's
chips.
Submitted by: Ville-Pertti Keinonen <will@iki.fi>
Rather than teaching pci_ioctl about hoses, we just pass down a magic number
& let the platform code figure out what the hose is based on what the bus
number is.
concept approved by dfr
resource_list_release. This removes the dependancy on the
layout of ivars.
* Move set_resource, get_resource and delete_resource from
isa_if.m to bus_if.m.
* Simplify driver code by providing wrappers to those methods:
bus_set_resource(dev, type, rid, start, count);
bus_get_resource(dev, type, rid, startp, countp);
bus_get_resource_start(dev, type, rid);
bus_get_resource_count(dev, type, rid);
bus_delete_resource(dev, type, rid);
* Delete isa_get_rsrc and use bus_get_resource_start instead.
* Fix a stupid typo in isa_alloc_resource reported by Takahashi
Yoshihiro <nyan@FreeBSD.org>.
* Print a diagnostic message if we can't assign resources to a PnP
device.
* Change device_print_prettyname() so that it doesn't print
"(no driver assigned)-1" for anonymous devices.
Memory" called as function 0x87 of interrupt 0x15. Since the Mylex RAID
adapter's BIOS used this function to access memory (actually PCI bus
space) beyond 16 MB, this patch also allows BTX to address all 4 Gig of
possible address space on i386+. Since the loader does not have room for
4 MB of page tables, this was done by turning off paging.
Paging was turned off via a compile time setting which defaults to off.
To enable paging, simply define the make variable PAGING.
rnordier might want to clean this up later.
Submitted by: W. Gerald Hicks <wghicks@bellsouth.net>,
Bosko Milekic <bmilekic@ares.dsuper.net>
Reviewed by: msmith
Required by: Mylex RAID adapter's BIOS
can provide the correct context to each signal handler.
Fix broken sigsuspend(): don't use p_oldsigmask as a flag, use SAS_OLDMASK
as we did before the linuxthreads support merge (submitted by bde).
Move ps_sigstk from to p_sigacts to the main proc structure since signal
stack should not be shared among threads.
Move SAS_OLDMASK and SAS_ALTSTACK flags from sigacts::ps_flags to proc::p_flag.
Move PS_NOCLDSTOP and PS_NOCLDWAIT flags from proc::p_flag to procsig::ps_flag.
Reviewed by: marcel, jdp, bde
to be dangerous. It will better serve us as a port building a KLD,
ala SKIP.
The hooks are staying although it would be better to port and use
the NetBSD pfil interface rather than have custom hooks.
their HotRod controller and on SIIG PCI ultra DMA controller. These
changes also made lots of the Promise code go away, its all much more
generic this way.
Get rid of atapi_immed_cmd, instead use the queue to move atapi commands
from interrupt context if nessesary, the entire atapi layer has
gotten an overhaul.
Lots of fixes to utililize the new features in subr_disk.c etc, and
get rid of the last biots of softc arrays in the drivers, the
only one left is atadevices which cannot easily go away (yet).
Use our own malloc names, its a lot easier to track memory usage this way.
General cleanup overall.
- Let physio take read/write compatible args and have it use uio->uio_rw
to determine the direction.
- physread/physwrite are now #defines for physio
- Remove the inversly named minphys(), dev->si_iosize_max takes over.
- Physio() always uses pbufs.
- Fix the check for non page-aligned transfers, now only unaligned
transfers larger than (MAXPHYS - PAGE_SIZE) get fragmented (only
interesting for tapes using max blocksize).
- General wash-and-clean of code.
Constructive input from: bde
NOTE: This will break building ntpd until ntpd has been upgraded to also
support draft 05. People that want to build ntpd in the meantime can
get patches from me.
- Work around a problem not yet solved in the tree (but solved in mine.)
device_get_ivars() should never be cast to a struct resource_list *
The solution, under review, involves the creation of a
device_get_resource_list() function. More later.
add nodes to the tree. Also, default to bus_generic_driver_added for
the BUS_DRIVER_ADDED method.
This allows newbus busses to be kldload'd.
Reviewed by: dfr
configuration information from a DPT card at a given port.
This is needed by the ISA bus front end (still to come) and the EISA
bus front end (which hasn't ever worked).
- Blow away dpt_eisa.h as the information it contains does not justify
an additional file.
- Convert dpt_eisa.c to use the onboard config instead of trying to
read the EISA configuration registers.
hexdump -C < /dev/drum
by simply refusing to do I/O from userland.
a panic. I'm not sure we even need /dev/drum anymore, it seems
to have been broken for a long time thi
- Some cleanup and improvements in the uhci and ohci drivers
- Support for plugging and unplugging devices improved
- Now available is bulk transport over OHCI controllers
- Resume and suspend have been temporarily been disabled again. Proper
support for it is available in the uhci.c and ohci.c files but I have
not yet spent the brain cycles to use it.
- OpenBSD now uses the USB stack as well
- Add FreeBSD tags
Remove the use of ukbd_disconnect and replace it with direct
calls to disable.
Change printf to DPRINTF
Remove the use of usbd_lock, change it to splusb()/splx()
o Remove unused defines from genassym.c that were needed
by the trampoline.
o Add load_gs_param function to support.s that catches
a fault when %gs is loaded with an invalid descriptor.
The function returns EFAULT in that case.
o Remove struct trapframe from mcontext_t and replace it
with the list of registers.
o Modify sendsig and sigreturn accordingly.
This commit contains a patch by bde.
Reviewed by: luoqi, jdp
the AMI PCI controllers using the 8LD firmware interface (40LD firmware
will be supported as soon as I have hardware to test with).
These controllers are rebadged by Dell as the PERC, as well as by HP
and possibly other vendors.
The old algorithm was:
if class == storage and subclass != SCSI device must be IDE
This results in claiming 'raid' and 'other' storage devices as IDE,
which is typically not the case.
Reviewed by: sos
- Move intrhook stuff into kernel.h
- Remove all occurrences of #device <device.h>
- Add kernel.h were necessary (nowhere)
- delete device.h
This file contained the structures for cfdata (old style config) and is no
longer used. It was included by most drivers.
It confuses the remote debugger as the definition of 'struct device' in
device.h is found before the one in bus_private.h.
struct sigcontext and ucontext_t/mcontext_t are defined in such
a way that both (ie struct sigcontext and ucontext_t) can be
passed on to sigreturn. The signal handler is still given a
ucontext_t for maximum flexibility.
For backward compatibility sigreturn restores the state for the
alternate signal stack from sigcontext.sc_onstack and not from
ucontext_t.uc_stack. A good way to determine which value the
application has set and thus which value to use, is still open
for discussion.
NOTE: This change should only affect those binaries that use
sigcontext and/or ucontext_t. In the source tree itself
this is only doscmd. Recompilation is required for those
applications.
This commit also fixes a lot of style bugs without hopefully
adding new ones.
NOTE: struct sigaltstack.ss_size now has type size_t again. For
some reason I changed that into unsigned int.
Parts submitted by: bde
sigaltstack bug found by: bde
two new functions spec_buf{read|write}.
Add sysctl vfs.bdev_buffered which defaults to 1 == true. This
sysctl can be used to experimentally turn buffered behaviour for
bdevs off. I should not be changed while any blockdevices are
open. Remove the misplaced sysctl vfs.enable_userblk_io.
No other changes in behaviour.
0x8024b04e) so that the cards description is used instead of overriding
it. While I'm here, add an ID for the SUP2080 and the SUP2030.
PR: kern/13983
Submitted by: Kurt D. Zeilenga <Kurt@OpenLDAP.Org> (SUP2030)
dfr (rest of change)
Reviewed by: dfr
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Reviewed by: dfr
kernel, but gcc provides a pessimal builtin for it.
Makefile.i386:
Added a variable (CONF_CFLAGS) for configuration-specific compiler flags.
LINT:
Use CONF_CFLAGS to inhibit use of gcc builtins.
and add a config option that allows one to default to 1FM@EOD for tapes
otherwise unquirked or unknown as to which to prefer. Note that tcopy
will be broken for these tapes until tcopy is fixed.
Add debuging for all failure cases in aha_cmd().
Always check DATAIN_REG_READY even if we're ready to exit the
read loop.
The last fix allows the AHA-1640 MCA SCSI adapter to operate
correctly and likely fixes problems on a few other oddball
adapters. (I suspect my Dell Drive Array in 1540 mode needs this.)
Reviewed by: Warner Losh
apm_saver uses the apm_display() routine from the apm system to
"suspend" the "display" part of the machine.
This is beneficial for some laptops (or other machines with
non-traditional displays) that choke on the 'green' saver's
effect.
Another way of looking at this is that it's the same as a screen
saver that does an 'apm -d 0' to blank the display and an 'apm -d 1'
to bring it back. One probably ought to use these commands to make
sure the effect will be correct before using it unattended.
1. Break out the definition of the soft state structure into an include
file.
2. un-static the soft state and apm_display(), and group them under a
comment that notes the dependency.
For unknown devices the output will now be
pci0: unknown card (vendor=0x109e, dev=0x0878) at 14.1 irq 19
instead of
pci0: unknown card DD^0878 (vendor=0x109e, dev=0x0878) at 14.1 irq 19
Before this change, the code used to take the PCI vendor id and translate it
into a three letter ASCII name.
For PnP devices, the vendor id _does_ map to a nice ASCII name
(eg Creative Labs PnP ID maps to "CTL", ESS PnP ID maps to "ESS")
But there is no such mapping for PCI devices, as can be seen by the
example above where the Brooktree PCI vendor ID maps to "DD^"
The PCI Special Interest Group confirmed they do not have any mappings
from vendor ID to ASCII.
of the number of times a particular type has been used. It's rather easy
to overflow. One site I'm looking at seems to do it in a matter of days.
On the Alpha this is a no-op since 'long' is 64 bit already. The sole
user of this interface seems to be vmstat -m and friends which will need
a recompile. The overheads of using a 64 bit int should be pretty light
as the kernel just does "calls++" type operations and that's it.
Turn on the 'new' if_ep driver which supports:
ISA 3c509
MCA 3c529
EISA 3c579
PCCARD 3c589
I think all we're missing is support for the VME bus and S-100 bus
Etherlink III cards.
The new code has been tested by a number of people and all the important
bits work. I've not been able to test the EISA code but will do so once
my hardware arrives. Since I've changed nothing in the EISA code I suspect
it will perform the same manner as before.
Future changes involve whacking the ISA and PCCARD front ends to use
newbus and to convert the driver to bus_space and make it use ifmedia.
This is the first working network driver that supports MCA bus devices btw.
Enjoy.
(behind the built-in ppb on hose 1) to be found:
When testing the adaptec controller on alpha, I realized I misread the xp1000
documentation and the way I'm calculating the bus number for PCI
config space accesses on the tsunami is wrong. I had thought that a bus
behind a ppb should be numbered as the nth bus in that hose, but it
actually needs to be the nth global bus within the system. The bus number
for the primary bus on a hose must always remain 0 when calculating config
space addresses.
and/or when using the card.
o Convert the driver to using bus_space. This allows alphas with
fxp's to boot, rather than panic'ing because rman_get_virtual()
doesn't really return a virtual address on alphas.
o Fix an alpha unaligned access error caused by some misfeature of
gcc/egcs: if link_addr & rbd_addr in the fxp_rfa struct are 32 bit
quantities, egcs will assume they are naturally aligned. So it will do
a ldl & some shifty/masky to twiddle 16 bit values in fxp_lwcopy().
However, if they are 16-bit aligned, the ldl will actually be done on
a 16-bit aligned value & we will panic with an unaligned access
error... Changing their definition to an array of chars seems to fix
this. I obtained this from NetBSD.
I've tested this on both i386 & alpha.
a 2940UW. The dp264 (and ds20, I think) have an AIC7895 on board so it
is important the ahc driver be in GENERIC so that FreeBSD can install on
these boxes.
around meant that the higher level close routine never gets called.
(phk is on the road; this is a quick fix to get things working and may need
more polish)
error for a directory. I have made this change after a great deal of
review although I cannot be absolutely sure that this meets the spec.
The issue devolves into whether changes in an underlying (UFS) directory
can cause NFS directory blocks to be renumbered. My read of the code
indicates that NFS directory blocks will not be renumbered, which means
that the cookies should still remain valid after a change is made to
the underlying directory. This being the case, a cookie error should
not be returned when a change is made to the underlying directory and,
instead, the NFS client should rely on mtime detection to invalidate and
reload the directory.
The use of mtime is problematic in of itself, due to insufficient
resolution, which is why I believe the original conservative error
handling was done. Still, there have been dozens of bug reports by
people needing solaris<->FreeBSD interoperability and these have to
be accomodated.
-----------------------------
The compatibility code and/or emulators have been updated:
iBCS2 now mostly uses the older syscalls. SVR4 now properly
handles all signals. This has been achieved by using the
new sigset_t throughout the emulator. The Linuxulator has
been severely updated. Internally the new Linux sigset_t is
made the default. These are then mapped to and from the
new FreeBSD sigset_t.
Also, rt_sigsuspend has been implemented in the Linuxulator.
Implementing this syscall basicly caused all this sigset_t
changing in the first place and the syscall has been used
throughout the change as a means for testing. It basicly is
too much work to undo the implementation so that it can
later be added again.
A special note on the use of sv_sigtbl and sv_sigsize in
struct sysentvec:
Every signal larger than sv_sigsize is not translated and is
passed on to the signal handler unmodified. Signals in the
range 1 upto and including sv_sigsize are translated.
The rationale is that only the system defined signals need to
be translated.
The emulators also have been updated so that the translation
tables are only indexed for valid (system defined) signals.
This change also fixes the translation bug already in the
SVR4 emulator.
-----------------------------
By introducing a new sigframe so that the signal handler operates
on the new siginfo_t and on ucontext_t instead of sigcontext, we
now need two version of sendsig and sigreturn.
A flag in struct proc determines whether the process expects an
old sigframe or a new sigframe. The signal trampoline handles
which sigreturn to call. It does this by testing for a magic
cookie in the frame.
The alpha uses osigreturn to implement longjmp. This means that
osigreturn is not only used for compatibility with existing
binaries. To handle the new sigset_t, setjmp saves it in
sc_reserved (see NOTE).
the struct sigframe has been moved from frame.h to sigframe.h
to handle the complex header dependencies that was caused by
the new sigframe.
NOTE: For the i386, the size of jmp_buf has been increased to hold
the new sigset_t. On the alpha this has been prevented by
using sc_reserved in sigcontext.
-----------------------------
The core of the signalling code has been rewritten to operate
on the new sigset_t. No methodological changes have been made.
Most references to a sigset_t object are through macros (see
signalvar.h) to create a level of abstraction and to provide
a basis for further improvements.
The NSIG constant has not been changed to reflect the maximum
number of signals possible. The reason is that it breaks
programs (especially shells) which assume that all signals
have a non-null name in sys_signame. See src/bin/sh/trap.c
for an example. Instead _SIG_MAXSIG has been introduced to
hold the maximum signal possible with the new sigset_t.
struct sigprop has been moved from signalvar.h to kern_sig.c
because a) it is only used there, and b) access must be done
though function sigprop(). The latter because the table doesn't
holds properties for all signals, but only for the first NSIG
signals.
signal.h has been reorganized to make reading easier and to
add the new and/or modified structures. The "old" structures
are moved to signalvar.h to prevent namespace polution.
Especially the coda filesystem suffers from the change, because
it contained lines like (p->p_sigmask == SIGIO), which is easy
to do for integral types, but not for compound types.
NOTE: kdump (and port linux_kdump) must be recompiled.
Thanks to Garrett Wollman and Daniel Eischen for pressing the
importance of changing sigreturn as well.
-----------------------------
Rename sigaction, sigprocmask, sigpending and sigsuspend to
osigaction, osigprocmask, osigpending and osigsuspend (resp)
and add new syscalls for them to support the new sisgset_t
without breaking existing binaries.
Change the prototype of sigaltstack to use the typedef stack_t
instead of struct sigaltstack to reflect that it is SUSv2
compliant.
Also, rename sigreturn to osigreturn and add a new syscall
to support the modified stackframe. The change is caused by
sigreturn operating on ucontext_t now and the fact that
siginfo_t has been updated to conform to SUSv2.
This happened to be my first "for real" broken world. I had broken
it once before, but nobody noticed, so it didn't count.
So, how do I get the "I broke world and all I got was the lousy t-shirt"
t-shirt?
of parity check and rebuild operations. This enables us
to stop the operation and restart at a later time.
enum parityop: Trivial enum to decide what parityops() is going to do.
could stand.
Define the correct return lengths for a number of ioctls.
Add ioctls VINUM_CHECKPARITY and VINUM_RESETPARITY, still to be fully
implemented.
ourselves. This breaks a vicious circle which caused
vinum to dereference a null vp if device nodes were
missing.
Reported-by: Brad Chisholm <sasblc@unx.sas.com>
Alec Wolman <wolman@cs.washington.edu>
check_drive: Don't take a drive down if it's only referenced.
read_drive: Remove unused variable.
get_empty_volume: initialize plexes to -1 (not allocated)
remove_drive_entry:
Remove recurse parameter (there's nothing below a drive in the hierarchy).
Use remove_sd_entry to remove sds, don't do it ourselves.
Log errors, don't throw rude remarks.
remove_plex_entry:
Don't use plex->subdisks as a loop limit, it gets changed in the
loop. This caused some removals to only remove half the subdisks.
Change logging of some "impossible" situations.
remove_volume_entry:
Use remove_plex_entry to remove plexes, don't do it ourselves.
update_sd_config:
Use set_sd_state to do the work.
will have to mknod yourself for now.
* don't eat the first write()
* partial rvplayer fix- don't panic on unaligned writes unless our
feeder chain requires them for downconversion. a fuller fix is
on the way.
I386_BUS_SPACE_IO. Compiles now on the Alpha, but likely will not
work due to bus space address <-> virtual address mapping bogons that
work for i386 but not alpha.
an empty mbuf to stay in the queue, then causing a needless panic
because sb_cc == 0 and sb_mbcnt != 0.
But we still need to panic rather than endlessly looping if, for
some reason, sb_cc == 0 and there are non-empty mbufs in the queue.
PR: kern/11988
Reviewed by: fenner
a lower layer to an upper layer. I'm not sure how necessary this is
for reading.
Fix bug in union_lookup() (note: there are probably still several bugs
in union_lookup()). This one set lerror as a side effect without
setting lowervp, causing copyup code further on down to crash on a null
lowervp pointer. Changed the side effect to use a temporary variable
instead.
work. Be more verbose when one cannot allocate IRQ, et al since this
is a common configuration problem. The cards have the IRQ soft wired
into their BIOS and do not try to do collision detection. This can
cause problems when this IRQ is the same as another card/device.
The PNP hasn't been tested. My PNP board is in a deployed system.
I'll sneak in testing of it sometime later. I've been able to mount
the 3.3R cdrom that arrived today and access files off it.
Submitted by: dfr
the link are equal to the default aliasing address. Do not zero them!
This will fix the problem with non-working links added with the source
and/or aliasing address equal to the default aliasing address, but the
default aliasing address is set later, after the link has been set up,
like both natd(8) and ppp(8) do (for objective reasons).
Reviewed by: Brian Somers <brian@FreeBSD.org>,
Eivind Eklund <eivind@FreeBSD.org>,
Charles Mott <cmott@srv.net>
Leadtek Winfast 2000 cards.
No audio support yet, just the card make is reported.
Submitted by: Craig <crh@outpost.co.nz>
Submitted by: Peter Wemm <peter@netplex.com.au>
isa_compat.c
Copied from sys/i386/isa/isa_compat.c. It includes
sys/pc98/pc98/isa_compat.h instead of sys/i386/isa/isa_compat.h.
isa_compat.h
Copied from sys/i386/isa/isa_compat.c. The ed driver is registered
in this file until pc98's ed driver is converted into new-bus style.
files.pc98
Use sys/pc98/pc98/isa_compat.c instead of sys/i386/isa/isa_compat.c.
if_ed.c
- Fixed the location of the include file.
- Disalbed pnp support.
