This driver works in PIO mode for now, interrupts are available only when
FIFO is enabled. The FIFO cannot be used with arbitrary sizes which defeat
its general use.
At some point we can add DMA transfers where the FIFO can be more useful.
Tested on uBMC (microBMC) and BBB.
Sponsored by: Rubicon Communications (Netgate)
consumers can configure clock frequency
- Add ti_prcm_clk_set_source_freq wrapper for clk_set_source_freq
- Add am335x_clk_set_arm_disp_freq function to control pixel clock
frequency for LCD and HDMI output. Both of them are sensitive
to frequency skews and we need to get pixel clock matching requested
frequency as close to possible
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
The DISP DPLL clock is slower and was making the PRU programs slower
on FreeBSD than on Linux.
Submitted by: Manuel Stuehn <freebsdnewbie at freenet.de>
MFC after: 1 week
Minimum LCDC is 2 so clock freq shouild be 2*max_pixel_clock. Maximum pixel
clock for HDMI is 148500 (1920x1080). But AM335x can not run in this mode
due to bandwidth and clock limitations
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
