merged juniper and mips2 code base. This represents the work of
Juniper Engineers, plus Oleksandr Tymoshenko, Wojciech Koszek, Warner
Losh, Olivier Houchard, Randall Stewert and others that have
contributed to the mips2 and/or mips2-jnpr perforce branches.
(ECMP) for both IPv4 and IPv6. Previously, multipath route insertion
is disallowed. For example,
route add -net 192.103.54.0/24 10.9.44.1
route add -net 192.103.54.0/24 10.9.44.2
The second route insertion will trigger an error message of
"add net 192.103.54.0/24: gateway 10.2.5.2: route already in table"
Multiple default routes can also be inserted. Here is the netstat
output:
default 10.2.5.1 UGS 0 3074 bge0 =>
default 10.2.5.2 UGS 0 0 bge0
When multipath routes exist, the "route delete" command requires
a specific gateway to be specified or else an error message would
be displayed. For example,
route delete default
would fail and trigger the following error message:
"route: writing to routing socket: No such process"
"delete net default: not in table"
On the other hand,
route delete default 10.2.5.2
would be successful: "delete net default: gateway 10.2.5.2"
One does not have to specify a gateway if there is only a single
route for a particular destination.
I need to perform more testings on address aliases and multiple
interfaces that have the same IP prefixes. This patch as it
stands today is not yet ready for prime time. Therefore, the ECMP
code fragments are fully guarded by the RADIX_MPATH macro.
Include the "options RADIX_MPATH" in the kernel configuration
to enable this feature.
Reviewed by: robert, sam, gnn, julian, kmacy
Make clock_if.m and subr_rtc.c standard on i386
Add hints for "atrtc" driver, for non-PnP, non-ACPI systems.
NB: Make sure to install GENERIC.hints into /boot/device.hints in these!
Nuke MD inittodr(), resettodr() functions.
Don't attach to PHP0B00 in the "attimer" dummy driver any more, and remove
comments that no longer apply for that reason.
Add new "atrtc" device driver, which handles IBM PC AT Real Time
Clock compatible devices using subr_rtc and clock_if.
This driver is not entirely clean: other code still fondles the
hardware to get a statclock interrupt on non-ACPI timer systems.
Wrap some overly long lines.
After it has settled in -current, this will be ported to amd64.
Technically this is MFC'able, but I fail to see a good reason.
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also fixed in this code.
frequency generation and what frequency the generated was anyones
guess.
In general the 32.768kHz RTC clock x-tal was the best, because that
was a regular wrist-watch Xtal, whereas the X-tal generating the
ISA bus frequency was much lower quality, often costing as much as
several cents a piece, so it made good sense to check the ISA bus
frequency against the RTC clock.
The other relevant property of those machines, is that they
typically had no more than 16MB RAM.
These days, CPU chips croak if their clocks are not tightly within
specs and all necessary frequencies are derived from the master
crystal by means if PLL's.
Considering that it takes on average 1.5 second to calibrate the
frequency of the i8254 counter, that more likely than not, we will
not actually use the result of the calibration, and as the final
clincher, we seldom use the i8254 for anything besides BEL in
syscons anyway, it has become time to drop the calibration code.
If you need to tell the system what frequency your i8254 runs,
you can do so from the loader using hw.i8254.freq or using the
sysctl kern.timecounter.tc.i8254.frequency.
user-mode lock manager, build a kernel with the NFSLOCKD option and
add '-k' to 'rpc_lockd_flags' in rc.conf.
Highlights include:
* Thread-safe kernel RPC client - many threads can use the same RPC
client handle safely with replies being de-multiplexed at the socket
upcall (typically driven directly by the NIC interrupt) and handed
off to whichever thread matches the reply. For UDP sockets, many RPC
clients can share the same socket. This allows the use of a single
privileged UDP port number to talk to an arbitrary number of remote
hosts.
* Single-threaded kernel RPC server. Adding support for multi-threaded
server would be relatively straightforward and would follow
approximately the Solaris KPI. A single thread should be sufficient
for the NLM since it should rarely block in normal operation.
* Kernel mode NLM server supporting cancel requests and granted
callbacks. I've tested the NLM server reasonably extensively - it
passes both my own tests and the NFS Connectathon locking tests
running on Solaris, Mac OS X and Ubuntu Linux.
* Userland NLM client supported. While the NLM server doesn't have
support for the local NFS client's locking needs, it does have to
field async replies and granted callbacks from remote NLMs that the
local client has contacted. We relay these replies to the userland
rpc.lockd over a local domain RPC socket.
* Robust deadlock detection for the local lock manager. In particular
it will detect deadlocks caused by a lock request that covers more
than one blocking request. As required by the NLM protocol, all
deadlock detection happens synchronously - a user is guaranteed that
if a lock request isn't rejected immediately, the lock will
eventually be granted. The old system allowed for a 'deferred
deadlock' condition where a blocked lock request could wake up and
find that some other deadlock-causing lock owner had beaten them to
the lock.
* Since both local and remote locks are managed by the same kernel
locking code, local and remote processes can safely use file locks
for mutual exclusion. Local processes have no fairness advantage
compared to remote processes when contending to lock a region that
has just been unlocked - the local lock manager enforces a strict
first-come first-served model for both local and remote lockers.
Sponsored by: Isilon Systems
PR: 95247 107555 115524 116679
MFC after: 2 weeks
overhead of packet capture by allowing a user process to directly "loan"
buffer memory to the kernel rather than using read(2) to explicitly copy
data from kernel address space.
The user process will issue new BPF ioctls to set the shared memory
buffer mode and provide pointers to buffers and their size. The kernel
then wires and maps the pages into kernel address space using sf_buf(9),
which on supporting architectures will use the direct map region. The
current "buffered" access mode remains the default, and support for
zero-copy buffers must, for the time being, be explicitly enabled using
a sysctl for the kernel to accept requests to use it.
The kernel and user process synchronize use of the buffers with atomic
operations, avoiding the need for system calls under load; the user
process may use select()/poll()/kqueue() to manage blocking while
waiting for network data if the user process is able to consume data
faster than the kernel generates it. Patchs to libpcap are available
to allow libpcap applications to transparently take advantage of this
support. Detailed information on the new API may be found in bpf(4),
including specific atomic operations and memory barriers required to
synchronize buffer use safely.
These changes modify the base BPF implementation to (roughly) abstrac
the current buffer model, allowing the new shared memory model to be
added, and add new monitoring statistics for netstat to print. The
implementation, with the exception of some monitoring hanges that break
the netstat monitoring ABI for BPF, will be MFC'd.
Zerocopy bpf buffers are still considered experimental are disabled
by default. To experiment with this new facility, adjust the
net.bpf.zerocopy_enable sysctl variable to 1.
Changes to libpcap will be made available as a patch for the time being,
and further refinements to the implementation are expected.
Sponsored by: Seccuris Inc.
In collaboration with: rwatson
Tested by: pwood, gallatin
MFC after: 4 months [1]
[1] Certain portions will probably not be MFCed, specifically things
that can break the monitoring ABI.
rqindex back in struct thread.
- Compile kern_switch.c independently again and stop #include'ing it from
schedulers.
- Remove the ts_thread backpointers and convert most code to go from
struct thread to struct td_sched.
- Cleanup the ts_flags #define garbage that was causing us to sometimes
do things that expanded to td->td_sched->ts_thread->td_flags in 4BSD.
- Export the kern.sched sysctl node in sysctl.h
vm/vm_contig.c, vm/vm_page.c, and vm/vm_pageq.c. Today, vm/vm_pageq.c
has withered to the point that it contains only four short functions,
two of which are only used by vm/vm_page.c. Since I can't foresee any
reason for vm/vm_pageq.c to grow, it is time to fold the remaining
contents of vm/vm_pageq.c back into vm/vm_page.c.
Add some comments. Rename one of the functions, vm_pageq_enqueue(),
that is now static within vm/vm_page.c to vm_page_enqueue().
Eliminate PQ_MAXCOUNT as it no longer serves any purpose.
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
The kernel config file is KERNCONF=MPC85XX, so the usual procedure applies:
1. make buildworld TARGET_ARCH=powerpc
2. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
This default config uses kernel-level FPU emulation. For the soft-float world
approach:
1. make buildworld TARGET_ARCH=powerpc TARGET_CPUTYPE=e500
2. disable FPU_EMU option in sys/powerpc/conf/MPC85XX
3. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
Approved by: cognet (mentor)
MFp4: e500
The PQ3 is a high performance integrated communications processing system
based on the e500 core, which is an embedded RISC processor that implements
the 32-bit Book E definition of the PowerPC architecture. For details refer
to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPC8555E
This port was tested and successfully run on the following members of the PQ3
family: MPC8533, MPC8541, MPC8548, MPC8555.
The following major integrated peripherals are supported:
* On-chip peripherals bus
* OpenPIC interrupt controller
* UART
* Ethernet (TSEC)
* Host/PCI bridge
* QUICC engine (SCC functionality)
This commit brings the main functionality and will be followed by individual
drivers that are logically separate from this base.
Approved by: cognet (mentor)
Obtained from: Juniper, Semihalf
MFp4: e500
and assignment.
- Add a reference to a struct cpuset in each thread that is inherited from
the thread that created it.
- Release the reference when the thread is destroyed.
- Add prototypes for syscalls and macros for manipulating cpusets in
sys/cpuset.h
- Add syscalls to create, get, and set new numbered cpusets:
cpuset(), cpuset_{get,set}id()
- Add syscalls for getting and setting affinity masks for cpusets or
individual threads: cpuid_{get,set}affinity()
- Add types for the 'level' and 'which' parameters for the cpuset. This
will permit expansion of the api to cover cpu masks for other objects
identifiable with an id_t integer. For example, IRQs and Jails may be
coming soon.
- The root set 0 contains all valid cpus. All thread initially belong to
cpuset 1. This permits migrating all threads off of certain cpus to
reserve them for special applications.
Sponsored by: Nokia
Discussed with: arch, rwatson, brooks, davidxu, deischen
Reviewed by: antoine
not have VTOC information about the partitions, it will be created.
This is because the VTOC information is used for the partition type
and FreeBSD's sunlabel(8) does not create nor use VTOC information.
For this purpose, new tags have been added to support FreeBSD's
partition types.
just em, there is an igb driver (this follows behavior with our Linux drivers).
All adapters up to the 82575 are supported in em, and new client/desktop support
will continue to be in that adapter.
The igb driver is for new server NICs like the 82575 and its followons.
Advanced features for virtualization and performance will be in this driver.
Also, both drivers now have shared code that is up to the latest we have
released. Some stylistic changes as well.
Enjoy :)
sectors so the geometry of large IDE disks has to be adjusted. This
corresponds to what the OpenSolaris dad(7D) driver does except that
the latter only tweaks sectors and effectively limits the mediasize
to 128GB so the cylinders and heads fields won't ever overflow. Not
limiting the mediasize is a compromise between allowing to use Sun
disk label as far as possible and being able to use the entire disk
with another disk label.
This allows to use the full capacity of large IDE disks if they were
not labeled under (Open)Solaris (in both ways of the meaning).
MFC after: 2 weeks
This allows to fix a problem with ARM kernel.bin not having the MFS image
embedded: it is objcopied from the kernel.noheader temporary ELF file, which
was not subject to embedding the MFS image previously.
Reviewed by: imp
Approved by: cognet (mentor)
a variety of bootloaders. This sometimes means that different loader
scripts are required within one ${MACHINE_ARCH}, which makes the
current practice of using ldscript.${MACHINE_ARCH} unsuitable.
Instead, make the default the current convention and allow the ld
scripts to be overridden as necessary.
If we aren't arm, pc98 or sun4v, then enable treating warnings like
errors. That doesn't mean these platforms aren't -Werror clean, just
that we haven't enforced it before. Someone with some spare time
should investigate these three platforms to see if any can be removed.
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
overridden at compile-time using kernel options of the same names.
Rather than doing a compile-time CTASSERT of buffer sizes being
even multiples of block sizes, just adjust them at boottime, as
the failure mode is more user-friendly.
MFC after: 2 months
PR: 119993
Suggested by: Scot Hetzel <swhetzel at gmail dot com>
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
implement shm_open(2) and shm_unlink(2) in the kernel:
- Each shared memory file descriptor is associated with a swap-backed vm
object which provides the backing store. Each descriptor starts off with
a size of zero, but the size can be altered via ftruncate(2). The shared
memory file descriptors also support fstat(2). read(2), write(2),
ioctl(2), select(2), poll(2), and kevent(2) are not supported on shared
memory file descriptors.
- shm_open(2) and shm_unlink(2) are now implemented as system calls that
manage shared memory file descriptors. The virtual namespace that maps
pathnames to shared memory file descriptors is implemented as a hash
table where the hash key is generated via the 32-bit Fowler/Noll/Vo hash
of the pathname.
- As an extension, the constant 'SHM_ANON' may be specified in place of the
path argument to shm_open(2). In this case, an unnamed shared memory
file descriptor will be created similar to the IPC_PRIVATE key for
shmget(2). Note that the shared memory object can still be shared among
processes by sharing the file descriptor via fork(2) or sendmsg(2), but
it is unnamed. This effectively serves to implement the getmemfd() idea
bandied about the lists several times over the years.
- The backing store for shared memory file descriptors are garbage
collected when they are not referenced by any open file descriptors or
the shm_open(2) virtual namespace.
Submitted by: dillon, peter (previous versions)
Submitted by: rwatson (I based this on his version)
Reviewed by: alc (suggested converting getmemfd() to shm_open())
machine-independent support for superpages. (The earlier part was
the rewrite of the physical memory allocator.) The remainder of the
code required for superpages support is machine-dependent and will
be added to the various pmap implementations at a later date.
Initially, I am only supporting one large page size per architecture.
Moreover, I am only enabling the reservation system on amd64. (In
an emergency, it can be disabled by setting VM_NRESERVLEVELS to 0
in amd64/include/vmparam.h or your kernel configuration file.)
dump using mechanically generated/extracted debugging output rather than
a simple memory dump. Current sources of debugging output are:
- DDB output capture buffer, if there is captured output to save
- Kernel message buffer
- Kernel configuration, if included in kernel
- Kernel version string
- Panic message
Textdumps are stored in swap/dump partitions as with regular dumps, but
are laid out as ustar files in order to allow multiple parts to be stored
as a stream of sequentially written blocks. Blocks are written out in
reverse order, as the size of a textdump isn't known a priori. As with
regular dumps, they will be extracted using savecore(8).
One new DDB(4) command is added, "textdump", which accepts "set",
"unset", and "status" arguments. By default, normal kernel dumps are
generated unless "textdump set" is run in order to schedule a textdump.
It can be canceled using "textdump unset" to restore generation of a
normal kernel dump.
Several sysctls exist to configure aspects of textdumps;
debug.ddb.textdump.pending can be set to check whether a textdump is
pending, or set/unset in order to control whether the next kernel dump
will be a textdump from userspace.
While textdumps don't have to be generated as a result of a DDB script
run automatically as part of a kernel panic, this is a particular useful
way to use them, as instead of generating a complete memory dump, a
simple transcript of an automated DDB session can be captured using the
DDB output capture and textdump facilities. This can be used to
generate quite brief kernel bug reports rich in debugging information
but not dependent on kernel symbol tables or precisely synchronized
source code. Most textdumps I generate are less than 100k including
the full message buffer. Using textdumps with an interactive debugging
session is also useful, with capture being enabled/disabled in order to
record some but not all of the DDB session.
MFC after: 3 months
define a set of named scripts. Each script consists of a list of DDB
commands separated by ";"s that will be executed verbatim. No higher
level language constructs, such as branching, are provided for:
scripts are executed by sequentially injecting commands into the DDB
input buffer.
Four new commands are present in DDB: "run" to run a specific script,
"script" to define or print a script, "scripts" to list currently
defined scripts, and "unscript" to delete a script, modeled on shell
alias commands. Scripts may also be manipulated using sysctls in the
debug.ddb.scripting MIB space, although users will prefer to use the
soon-to-be-added ddb(8) tool for usability reasons.
Scripts with certain names are automatically executed on various DDB
events, such as entering the debugger via a panic, a witness error,
watchdog, breakpoint, sysctl, serial break, etc, allowing customized
handling.
MFC after: 3 months
captured to a memory buffer for later inspection using sysctl(8), or in the
future, to a textdump.
A new DDB command, "capture", is added, which accepts arguments "on", "off",
"reset", and "status".
A new DDB sysctl tree, debug.ddb.capture, is added, which can be used to
resize the capture buffer and extract buffer contents.
MFC after: 3 months
a pointer to struct bus_space. The structure contains function
pointers that do the actual bus space access.
The reason for this change is that previously all bus space
accesses were little endian (i.e. had an explicit byte-swap
for multi-byte accesses), because all busses on Macs are little
endian.
The upcoming support for Book E, and in particular the E500
core, requires support for big-endian busses because all
embedded peripherals are in the native byte-order.
With this change, there's no distinction between I/O port
space and memory mapped I/O. PowerPC doesn't have I/O port
space. Busses assign tags based on the byte-order only.
For that purpose, two global structures exist (bs_be_tag and
bs_le_tag), of which the address can be taken to get a valid
tag.
Obtained from: Juniper, Semihalf
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
processors (it's the PowerPC Operating Environment Architecture).
AIM designates the processors made by the Apple-IBM-Motorola
alliance and those we typically support.
While here, remove the NetBSD option IPKDB. It's not an option
used by us. Also, PPC_HAVE_FPU is not used by us either. Remove
that too.
Obtained from: Juniper, Semihalf
the ABI when enabled. There is no longer an embedded lock_profile_object
in each lock. Instead a list of lock_profile_objects is kept per-thread
for each lock it may own. The cnt_hold statistic is now always 0 to
facilitate this.
- Support shared locking by tracking individual lock instances and
statistics in the per-thread per-instance lock_profile_object.
- Make the lock profiling hash table a per-cpu singly linked list with a
per-cpu static lock_prof allocator. This removes the need for an array
of spinlocks and reduces cache contention between cores.
- Use a seperate hash for spinlocks and other locks so that only a
critical_enter() is required and not a spinlock_enter() to modify the
per-cpu tables.
- Count time spent spinning in the lock statistics.
- Remove the LOCK_PROFILE_SHARED option as it is always supported now.
- Specifically drop and release the scheduler locks in both schedulers
since we track owners now.
In collaboration with: Kip Macy
Sponsored by: Nokia
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
o Disklabels can have between 8 and 20 partitions (inclusive).
o No device special file is created for the raw partition.
o Switch ia64 to use this backend.
o No support for boot code yet.
INCLUDE_CONFIG_FILE. Make a user to look at what config(8) actually does,
and how can one fetch actual configuration file.
Reported by: many
Reviewed by: cognet (mentor)
Approved by: cognet (mentor)
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
hack means you can get the units and flags to match up more easily with
serial consoles on machines with acpi tables that cause the com ports
to be probed in the wrong order (and hence get the wrong sio unit number).
This replaces the common alternative hack of editing the code to comment
out the acpi attachment. This could go away entirely when device wiring
patches are committed.
Currently, Giant is not too much contented so that it is ok to treact it
like any other mutexes.
Please don't forget to update your own custom config kernel files.
Approved by: cognet, marcel (maintainers of arches where option is
not enabled at the moment)
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
This includes:
o mtree (for legal/intel_wpi)
o manpage for i386/amd64 archs
o module for i386/amd64 archs
o NOTES for i386/amd64 archs
Approved by: mlaier (comentor)
lock optimized for almost exclusive reader access. (see also rmlock.9)
TODO:
Convert to per cpu variables linkerset as soon as it is available.
Optimize UP (single processor) case.
in the TrustedBSD MAC Framework:
- Add mac_atalk.c and add explicit entry point mac_netatalk_aarp_send()
for AARP packet labeling, rather than using a generic link layer
entry point.
- Add mac_inet6.c and add explicit entry point mac_netinet6_nd6_send()
for ND6 packet labeling, rather than using a generic link layer entry
point.
- Add expliict entry point mac_netinet_arp_send() for ARP packet
labeling, and mac_netinet_igmp_send() for IGMP packet labeling,
rather than using a generic link layer entry point.
- Remove previous genering link layer entry point,
mac_mbuf_create_linklayer() as it is no longer used.
- Add implementations of new entry points to various policies, largely
by replicating the existing link layer entry point for them; remove
old link layer entry point implementation.
- Make MAC_IFNET_LOCK(), MAC_IFNET_UNLOCK(), and mac_ifnet_mtx global
to the MAC Framework rather than static to mac_net.c as it is now
needed outside of mac_net.c.
Obtained from: TrustedBSD Project
