side effect of something else using them. If they haven't been loaded
already but you want to use them, say for configuring a jail, you're out
of luck.
So add a knob to always load the default rulesets. While I'm here document
the other devfs_ knobs in rc.conf.5.
- ipv6_enable + ipv6_gateway_enable should unset ACCEPT_RTADV by default for
backward compatibility.
- Configurations in ipv6_prefix_IF should be recognized even if there is no
ifconfig_IF_ipv6.
- DAD wait should be performed at once, not on a per-interface basis, if
possible. This fixes an issue that a system with a lot of IPv6-capable
interfaces takes too long for booting.
MFC after: 1 week
creating stray "log" symlinks if the mount fails. That apparently
happens in some ezjail configs.
PR: conf/143084
Submitted by: Dirk Engling <erdgeist at erdgeist.org>
Reviewed by: simon
MFC after: 2 weeks
dhclient is no longer a real service, it is a helper script
for /etc/rc.d/netif and devd. Its direct invocation isn't
needed to bring the network up.
Approved by: jhb
The concept of set_rcvar() was nice in theory, but the forks
it creates are a drag on the startup process, which is especially
noticeable on slower systems, such as embedded ones.
assignments to the literal values it would have returned.
The concept of set_rcvar() was nice in theory, but the forks
it creates are a drag on the startup process, which is especially
noticeable on slower systems, such as embedded ones.
During the discussion on freebsd-rc@ a preference was expressed for
using ${name}_enable instead of the literal values. However the
code portability concept doesn't really apply since there are so
many other places where the literal name has to be searched for
and replaced. Also, using the literal value is also a tiny bit
faster than dereferencing the variables, and every little bit helps.
Document the current semantics of the 'quiet' command prefix
in the rc.subr(8).
Fix dhclient rc.d script: it should not call err() for
non-DHCP-enabled interface when it is called from devd, because the
latter just blindly calls 'service dhclient quietstart' on each "link
up" event.
Since the 'quietstart' will silence the message "Cannot 'start' <foo>.
Set <foo>_enable to YES in /etc/rc.conf or use 'onestart' instead of
'start'." and running dhclient on the non-DHCP-enabled interface is
the same thing as running the service <foo> without <foo>_enable set,
such modification is in sync with the current semantics of the 'quiet'
prefix.
Approved by: glebius
Reviewed by: freebsd-rc list
MFC after: 2 weeks
o Make the pfsync.ko actually usable. Before this change loading it
didn't register protosw, so was a nop. However, a module /boot/kernel
did confused users.
o Rewrite the way we are joining multicast group:
- Move multicast initialization/destruction to separate functions.
- Don't allocate memory if we aren't going to join a multicast group.
- Use modern API for joining/leaving multicast group.
- Now the utterly wrong pfsync_ifdetach() isn't needed.
o Move module initialization from SYSINIT(9) to moduledata_t method.
o Refuse to unload module, unless asked forcibly.
o Improve a bit some FreeBSD porting code:
- Use separate malloc type.
- Simplify swi sheduling.
This change is probably wrong from VIMAGE viewpoint, however pfsync
wasn't VIMAGE-correct before this change, too.
Glanced at by: bz
with FreeBSD easier for vendors.
- For optional files use variables starting with underscore.
Both changes make rc.d/Makefile look similar to sys/modules/Makefile.
Reviewed by: dim
MK_LIBCPLUSPLUS=yes to enable). This is a work-in-progress. It works for
me, but is not guaranteed to work for anyone else and may eat your dog.
To build C++ using libc++, add -stdlib=libc++ to your CXX and LD flags.
Bug reports welcome, bug fixes even more welcome...
Approved by: dim (mentor)
only 1 old file to be saved, so fix this. Problem raised in the PR,
but actually required a different solution.
While I'm here, fix a very old off-by-one error causing 1 more file
than specified in daily_accounting_save to be saved because acct.0
was not taken into account (pun intended). Change that, and use a more
thorough method of finding old files to delete. Partly just because this
is the right thing to do, but also to silently fix the extra log that
would have been left behind forever with the previous method.
PR: conf/160848
Submitted by: Andrey Zonov <andrey@zonov.org>
the /etc/rc.d/nfsd script sets vfs.nfsd.server_max_nfsvers to 3.
Then, when you set nfsv4_server_enable=YES in rc.conf, and restart nfsd
via the rc.d script, without rebooting, the sysctl does *not* get reset
to max version 4, so NFSv4 still doesn't work.
Fix this by explicitly setting vfs.nfsd.server_max_nfsvers to 4 when
NFSv4 is requested.
I also added resetting of the nfs_privport sysctls, since this has the
same issue: nfs_reserved_port_only=YES in rc.conf sets the nfs_privport
sysctl to 1, but in the other case, the sysctl doesn't get reset to 0.
Reviewed by: rmacklem
Silence from: rc@
MFC after: 3 days
Variable 'rc_force' is accessible only at the time of rc_run_command,
so it can't be examined from the script's main code.
Spotted by: hrs
Reviewed by: hrs, des
Approved by: des
MFC after: 2 weeks
the logic (true/false) of the matching.
- Add "!usbus[0-9]+" to IFNET ATTACH notification handler in the default
devd.conf to prevent rc.d/netif from running when usbus[0-9]+ is attached.
Reviewed by: imp
Make sure that static ARP and NDP bindings are set before NETWORKING.
As static_ndp is based on static_arp, pass copyright to the project with
permission of the original author (delphij@).
Reviewed by: delphij@FreeBSD.org
MFC after: 3 days
for interfaces which were not configured for DHCP *unless* rc_force was set;
the correct logic is to run dhclient for those interfaces *only if* rc_force
is set.
Broken by: des@
Noticed by: everybody and his dog
Submitted by: rea@
PR: bin/161733
too-thorough cleanup of unused files, in r213695. Also make sure these
get installed under /usr/share/doc.
Submitted by: rwatson, brooks
Pointy hat to: dim
MFC after: 3 days
