ndis_scan() is called. However, ndis_scan() is invoked from softclock()
and cannot sleep. Move ndis_scan_results() to the ndis' driver's scan_end
hook instead.
Submitted by: Paul B Mahol onemda of gmail
MFC after: 1 week
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
baseline subtraction, and are very temperature sensitive, so would slowly
drift out of a calibrated state when under load. Escape this by taking
the last frame before we decide that the pad is idle as a finger-free
baseline.
Tested on: iBook G4
long as I remember, and completely superseded by better maintained umass(4).
It's main idea was to optionally avoid CAM dependency for such devices, but
with move ATA to CAM, it is not actual any more.
No objections: hselasky@, thompsa@, arch@
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
- fix a system deadlock on process exit when the sample buffer
is full (pmclog_loop blocked in fo_write) and pmcstat exit.
Reviewed by: jkoshy
MFC after: 3 weeks
bits on seems to confuse hardware TX engine.
- For 350 chips, set TX desc's buffer physical address before turning on the
TX desc valid bit.
Submitted by: Jeremy O'Brien obrien654j | gmail, sephe
Obtained from: DragonFly BSD
- Extend XPT-SIM transfer settings control API. Now it allows to report to
SATA SIM number of tags supported by each device, implement ATA mode and
SATA revision negotiation for both SATA and PATA SIMs.
- Make ahci(4) and siis(4) to use submitted maximum tag number, when
scheduling requests. It allows to support NCQ on devices with lower tags
count then controller supports.
- Make PMP driver to report attached devices connection speeds.
- Implement ATA mode negotiation between user settings, device and
controller capabilities.
Tx/Rx/Rx return ring such that large part of status block was not
used at all. All bge(4) controllers except BCM5700 AX/BX has a
feature to control the size of status block. So use minimum status
block size allowed in controller. This reduces number of DMAed
status block size to 32 bytes from 80 bytes.
seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
Tested by: current
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
Reviewed by: davidch
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
update and then clear status block. Previously it used to access
these index without synchronization which may cause problems when
bounce buffers are used. Also add missing bus_dmamap_sync(9) in
polling handler. Since we now update status block in driver, adjust
bus_dmamap_sync(9) for status block.
checking IFF_DRV_RUNNING and IFF_DRV_OACTIVE flags. Also if we
have less than 16 free send BDs set IFF_DRV_OACTIVE and try it
later. Previously bge(4) used to reserve 16 free send BDs after
loading dma maps but hardware just need one reserved send BD. If
prouder index has the same value of consumer index it means the Tx
queue is empty.
While I'm here check IFQ_DRV_IS_EMPTY first to save one lock
operation.
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
Reviewed by: marius
