- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
ipsec*_set_policy and do the privilege check only if needed.
Try to assimilate both ip*_ctloutput code blocks calling ipsec*_set_policy.
Reviewed by: rwatson
a variety of bootloaders. This sometimes means that different loader
scripts are required within one ${MACHINE_ARCH}, which makes the
current practice of using ldscript.${MACHINE_ARCH} unsuitable.
Instead, make the default the current convention and allow the ld
scripts to be overridden as necessary.
If we aren't arm, pc98 or sun4v, then enable treating warnings like
errors. That doesn't mean these platforms aren't -Werror clean, just
that we haven't enforced it before. Someone with some spare time
should investigate these three platforms to see if any can be removed.
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
aligned (or at least not cross a page boundary). However, it turns out
that on at least one machine one table header does cross a page boundary.
This caused problems with the MADT early probe as it uses the crash dump
map to load ACPI tables by loading the RSDT/XSDT into pages 1 ... N and
loading the header of each ACPI table header into page 0 looking for the
MADT. However, if a table header crossed a page boundary, then page 1
would get trashed resulting in a panic. Fix this by reserving the first
2 pages for ACPI table headers (headers are less than a page in size,
so 2 pages will be sufficient) and use pages 2 .. N for the RSDT and XSDT.
Note: amd64 should probably be simplified to just use pmap_mapbios()
for all these tables which will use the direct map and not need the
crash dump hack.
MFC after: 5 days
Tested on: i386
Reported by: Pete French petefrench of ticketswitch.com
read socket buffers in shutdown() and close():
- Call socantrcvmore() before sblock() to dislodge any threads that
might be sleeping (potentially indefinitely) while holding sblock(),
such as a thread blocked in recv().
- Flag the sblock() call as non-interruptible so that a signal
delivered to the thread calling sorflush() doesn't cause sblock() to
fail. The sblock() is required to ensure that all other socket
consumer threads have, in fact, left, and do not enter, the socket
buffer until we're done flushin it.
To implement the latter, change the 'flags' argument to sblock() to
accept two flags, SBL_WAIT and SBL_NOINTR, rather than one M_WAITOK
flag. When SBL_NOINTR is set, it forces a non-interruptible sx
acquisition, regardless of the setting of the disposition of SB_NOINTR
on the socket buffer; without this change it would be possible for
another thread to clear SB_NOINTR between when the socket buffer mutex
is released and sblock() is invoked.
Reviewed by: bz, kmacy
Reported by: Jos Backus <jos at catnook dot com>
The only downside is that it renames pmap_vac_me_harder() to pmap_fix_cache().
From Mark's email on -arm :
pmap_get_vac_flags(), pmap_vac_me_harder(), pmap_vac_me_kpmap(), and
pmap_vac_me_user() has been rewritten as pmap_fix_cache() to be more
efficient in the kernel map case. I also removed the reference to
the md.kro_mappings, md.krw_mappings, md.uro_mappings, and md.urw_mappings
counts.
In pmap_clearbit(), we can also skip over tests and writeback/invalidations
in the PVF_MOD and PVF_REF cases if those bits are not set in the pv_flag.
PVF_WRITE will turn caching back on and remove the PV_MOD bit.
In pmap_nuke_pv(), the vm_page_flag_clear(pg, PG_WRITEABLE) has been moved
to the pmap_fix_cache().
We can be more agressive in attempting to turn caching back on by calling
pmap_fix_cache() at times that may be appropriate to turn cache on
(a kernel mapping has been removed, a write has been removed or a read
has been removed and we know the mapping does not have multiple write
mappings to a page).
In pmap_remove_pages() the cpu_idcache_wbinv_all() is moved to happen
before the page tables are NULLed because the caches are virtually
indexed and virtually tagged.
In pmap_remove_all(), the pmap_remove_write(m) is added before the
page tables are NULLed because the caches are virtually indexed and
virtually tagged. This also removes the need for the caches fixing routine
(whichever is being used pmap_vac_me_harder() or pmap_fix_cache()) to be
called on any of these mappings.
In pmap_remove(), I simplified the cache cleaning process and removed
extra TLB removals. Basically if more than PMAP_REMOVE_CLEAN_LIST_SIZE
are removed, then just flush the entire cache.
This implemntation made for growing down stack organization like i386/amd64
platforms have, but prefers different machine dependent version if it is present.
o conversion to callout(9) API.
o add a missing driver lock in bfe_ifmedia_sts().
o use our callout to drive watchdog timer.
o restart Tx routine if pending queued packets are present in
watchdog handler.
o unarm watchdog timer only if there are no queued packets.
o don't blindly reset phy and let phy driver handle link change
request in bfe_init_locked().
o return the status of mii_mediachg() to caller in
bfe_ifmedia_upd(). Previously it always returned 0 to caller.
o add check for IFF_DRV_RUNNING flag as well as IFF_DRV_OACTIVE
in bfe_start_locked().
o implement miibus_statchg method that keeps track of current
link state changes as well as negotiated speed/duplex/
flow-control configuration.
Reprogram MAC to appropriate duplex state. Flow-control
configuration was also implemented but commented out at the
moment. The flow-control configuration will be enabled again
after we have general flow-control framework in mii layer.
Reported by: Yousif Hassan < yousif () alumni ! jmu ! edu >
Tesdted by: Yousif Hassan < yousif () alumni ! jmu ! edu >
This makes sure that process tokens credentials with un-initialized
audit contexts are handled correctly. Currently, when invariants are
enabled, this change fixes a panic by ensuring that we have a valid
termid family. Also, this fixes token generation for process tokens
making sure that userspace is always getting a valid token.
This is consistent with what Solaris does when an audit context is
un-initialized.
Obtained from: TrustedBSD Project
MFC after: 1 week
relabel check for MLS rather than returning 0 directly.
This problem didn't result in a vulnerability currently as the central
implementation of ifnet relabeling also checks for UNIX privilege, and
we currently don't guarantee containment for the root user in mac_mls,
but we should be using the MLS definition of privilege as well as the
UNIX definition in anticipation of supporting root containment at some
point.
MFC after: 3 days
Submitted by: Zhouyi Zhou <zhouzhouyi at gmail dot com>
Sponsored by: Google SoC 2007
