Use pmap_TLB_invalidate instead of invltlb_1pg to eliminate
unnecessary IPIs.
pmap_remove, pmap_protect and pmap_remove_pages:
Use pmap_TLB_invalidate_all instead of invltlb to eliminate
unnecessary IPIs.
pmap_copy:
Use cpu_invltlb instead of invltlb when updating APTDpde.
pmap_changebit:
Rather than deleting the unused "set bit" option (which may be
useful later), make pmap_changebit an inline that is used
by the new pmap_clearbit procedure.
Collectively, the first three changes reduce the number of TLB shootdown
IPIs by 1/3 for a kernel compile.
attached to the nexus. With one exception, this (for example) allows
you to do wierd things like kldload the eisa bus on the fly and then
drivers, and have it auto probe the eisa bus when the drivers come online.
The one exception being pci, it only adds the pcib after the presence of
the pci bus is detected and that's #if'ed code.
A side effect of this is that isa and eisa will be attached to the nexus
directly rather than the PCI->ISA or PCI->EISA bridges. I'm not sure if
this is good or bad at this point, but it seems to be closer to the way
things are for the i386 family... This is likely to be followed up.
This also fixes compilation without a PCI bus configured and will allow
eisa to work without PCI too.
- fix cut/paste problem. :-)
- don't forget to call isa_dmacascade()
- reset the port after we release resources.
That last one is a trap to watch out for.. The isa bus driver uses the
same port/irq/mem/etc variables for the initial probe hints as it does
for allocation/deallocation tracking. Releasing a resource clears the
variable and then you loose the hint during attach.. (ouch!)
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.
Submitted by: Doug Rabson <dfr@nlsystems.com>
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
only worked for configurations with "swap on generic".
usr.sbin/config/config.y:
- ignore all "swap [on] device ...' specifications except for
warning about them. They haven't done anything related to swap
for almost 4 years, and were previously silently ignored,
except for "swap on generic" which stopped swap${KERNEL}.c
from being generated. Code to support swapping is now deader
than before.
usr.sbin/config/mkswapconf.c:
- don't generate a dummy setconf() function in swap${KERNEL}.c.
sys/i386/conf/files.i386:
- swapgeneric.c is now standard. It should be merged into autoconf.c
so that it doesn't conflict with swap${KERNEL}.c for kernels named
"generic".
sys/i386/i386/autoconf.c:
- don't call setroot() for mfs roots. Since setroot() doesn't do anything
harmful, this was just a waste of time, except possibly for booting with
-a it may have helped prevent an undesireable call to setconf() by
finding a bogus rootdev.
- honor -a for ffs roots. -a now overrides all other ways of specifying
the root device. Previously, -r had precedence over -a, and the -a
handling was usually a no-op.
- don't honor -a for non-ffs roots, since it would currently just get in
the way of a clean panic.
sys/i386/i386/swapgeneric.c:
- don't declare things that are now always declared in swap${KERNEL}.c.
Don't decide things that are now decided in autoconf.c. Code to
support the "generic" case is now dead instead of useless.
in the RB_ASKNAME case. I had thought that I made this change in
rev.1.18, but rev.1.18 only affects obscure subcases of the
RB_DFLTROOT case (subcases where the compiled in default root is
not found in bdevsw[] -- then the root device is set to the first
device in the half-baked table that is also in bdevsw[]).
Removed yet more vestiges of config-time swap configuration.
All it did was match a specific device ID and turn on a quirk for
the wdc driver.
Incidently, at line 1462 there is a return that prevents the generic
ide_pci code from trying to look at the device. I'd be interested
to know if we can take out the return and let the generic code "see" it.
I've left the return in because that's the way it worked before.
(Be sure to rerun config after cvsup or you'll get undefined files!)
perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
Sense ${DEBUG} to decide on building kernel.debug or not.
Use a common install and install.debug target to minimize duplication.
(I deleted the ELF transition kernel warning, it was getting dated..)
Requested-by: ache
bde
dg
Modify targets for debug kernels: when -g was specified, make will
now build a debug kernel called kernel.debug, and create a stripped
version called kernel at the same time. The two targets install and
install.debug are otherwise unchanged.
Requested-by: dillon
Update man page accordingly.
Reduce synth_info.name lenght for binary compatibility.
o sys/i386/isa/sound/mpu401.c
Reduce mpu device number info to avoid overflow of mpu_synth_info.name.
Submitted by: Akio Morita <amorita@meadow.scphys.kyoto-u.ac.jp>
2. Config complains if you use -g:
Debugging is enabled by default, there is no ned to specify the -g option
3. Config warns you if you don't use -s:
Building kernel with full debugging symbols. Do
"config -s BSD" for historic partial symbolic support.
To install the debugging kernel, do make install.debug
(BSD was the name of the config file I used; I print out the same
name).
4. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 and config to
work if a kernel name other than 'kernel' is specified. This is
not absolutely necessary, but useful, and it was relatively easy.
I now have a kernel called /crapshit :-)
5. Modify Makefile.i386, Makefile.alpha, Makefile.pc98 "clean" target
to remove both the debug and normal kernel.
6. Modify all to install the stripped kernel by default and the debug
kernel if you enter "make install.debug".
7. Update version number of Makefiles and config.
Split out ioctl handler a little more cleanly, add memory
range attribute handling for both kernel and user-space
consumers.
pmap.c
Remove obsolete P6 MTRR-related code.
i686_mem.c
Map generic memory-range attribute interface to the P6 MTRR
model.
Networks Tigon 1 and Tigon 2 chipsets. There are a _lot_ of OEM'ed
gigabit ethernet adapters out there which use the Alteon chipset so
this driver covers a fair amount of hardware. I know that it works with
the Alteon AceNIC, 3Com 3c985 and Netgear GA620, however it should also
work with the DEC/Compaq EtherWORKS 1000, Silicon Graphics Gigabit
ethernet board, NEC Gigabit Ethernet board and maybe even the IBM and
and Sun boards. The Netgear board is the cheapest (~$350US) but still
yields fairly good performance.
Support is provided for jumbo frames with all adapters (just set the
MTU to something larger than 1500 bytes), as well as hardware multicast
filtering and vlan tagging (in conjunction with the vlan support in
-current, which I should merge into -stable soon). There are some hooks
for checksum offload support, but they're turned off for now since
FreeBSD doesn't have an officially sanctioned way to support checksum
offloading (yet).
I have not added the 'device ti0' entry to GENERIC since the driver
with all the firmware compiled in is quite large, and it doesn't really
fit into the category of generic hardware.
1. Switch to pmap_TLB_invalidate from invltlb, eliminating a full TLB
flush where a single-page flush suffices. (Also, this eliminates some
unnecessary IPIs.)
2. Use "loadandclear" to update the pte, eliminating a race condition
on SMPs.
Change #2 should be committed to -STABLE.
unallocated parts of the last page when the file ended on a frag
but not a page boundary.
Delimitted by tags PRE_MATT_MMAP_EOF and POST_MATT_MMAP_EOF,
in files alpha/alpha/pmap.c i386/i386/pmap.c nfs/nfs_bio.c vm/pmap.h
vm/vm_page.c vm/vm_page.h vm/vnode_pager.c miscfs/specfs/spec_vnops.c
ufs/ufs/ufs_readwrite.c kern/vfs_bio.c
Submitted by: Matt Dillon <dillon@freebsd.org>
Reviewed by: Alan Cox <alc@freebsd.org>
the address of the ps_strings structure to the process via %ebx.
For other kinds of binaries, %ebx is still zeroed as before.
Submitted by: Thomas Stephens <tas@stephens.org>
Reviewed by: jdp
In particular, replace the unused field pmap::pm_flag by pmap::pm_active,
which is a bit mask representing which processors have the pmap activated.
(Thus, it is a simple Boolean on UPs.)
Also, eliminate an unnecessary memory reference from cpu_switch()
in swtch.s.
Assisted by: John S. Dyson <dyson@iquest.net>
Tested by: Luoqi Chen <luoqi@watermarkgroup.com>,
Poul-Henning Kamp <phk@critter.freebsd.dk>
Add Sound Card ID for the nss(NEC PC-9801-86 Sound System) driver.
Old name of this driver was pcm driver in FreeBSD 2.2.x.
Fix lack of the length of the name member of the synth_info structure.
(attach_mpu401 in sys/i386/isa/sound/mpu401.c requires 33 chars.)
o sys/i386/isa/sound/dev_table.h
Add the DMAbuf flags definition DMA_DISABLE.
Add the nss driver entry.
o sys/i386/isa/sound/dmabuf.c
Add the DMA_DISABLE flag check in DMAbuf_outputintr and DMAbuf_inputintr
to disable DMA control in FIFO only use (nss driver required).
o sys/i386/isa/sound/local.h
Add the nss driver entry.
o sys/i386/isa/sound/mpu401.c
Replace inb function in probe_mpu401 to mpu401_status macro.
Wrap macro argument for above replace.
Add I/O port maping macro for NEC PC-98x1 arch.
Add delay in NEC PC-98x1 arch.
o sys/i386/isa/sound/pcm86.c
Change driver name to avoid name space conflict to new pcm driver.
Fix NEC PC-9801-86 driver to work on RELENG_3 branch or latter.
o sys/i386/isa/sound/sound_calls.h
Fix the mpuintr definition.
Add the nss driver entry.
attach_nss, probe_nss, nssintr
o sys/i386/isa/sound/soundcard.c
Fix lack of the mpuintr registration.
Add the nss driver entry.
o sys/pc98/conf/files.pc98
Add the nss driver entry.
Reviewed by: kato
Submitted by: Akio Morita <amorita@meadow.scphys.kyoto-u.ac.jp>
- Make a copy of the information block returned in the vm86 space
by the VESA BIOS init function. Otherwise it will be overwritten
by subsequent BIOS calls in the same vm86 context.
Well, better late than newer, but things has been hectic
around here, sorry for the long delay.
DMA support has been added to the ATA disk driver.
This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers.
The promise support works without the BIOS on the board,
and timing modes are set to support up to UDMA speed. This
solves the problems with having more than one promise controller
in the same system.
There is support for "generic" DMA, that might work on other
controllers, but now you have been warned :)
More chipset specific code will come soon, I have to find testers
with the approbiate HW, more on that when I have it ready.
The system now uses its own major numbers, please run MAKEDEV
with the devices you need (ad?, acd?, afd?, ast?).
For now the disk driver will also attach to the old wd major
so one can at least boot without this step, but be warned, this
will eventually go away. The bootblocks will have to be changed
before one can boot directly from an "ad" device though.
Fixed problems:
All known hang problems should be solved
The probe code has been sligthly changed, this should solve
the reports I have lying around (I hope).
Hangs when accessing ata & atapi device on the same channel simultaniously.
A real braino in ata_start caused this, fixed.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, agaiin you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
affects cases where there is a slave but no master. These bugs
were usually recovered from provided ATAPI was configured, but only
after lengthy delays. Configuring ATAPI still fixes some bugs for
non-atapi drives.
Don't wait for seek complete in wdreset(). If necessary for pre-ata
drives, it can be waited for later (we got it wrong by only looking
at it for drive 0 anyway). It is set as part of a historical
signature for ata drives but doesn't say anything useful about the
reset state. It is cleared as part of a non-historical signature
for atapi drives so that drivers which don't understand atapi drives
seem to see no drive. Waiting for it caused lengthy delays and
broke the status returned by wdreset() in cases where the master
was not an ata drive. Then the whole wdprobe() failed in some
cases where the recovery code didn't work.
Don't wait for drive ready in wdreset(). The considerations are
the same as for seek complete, except drive ready does say something
useful about the reset state of ata drives, and waiting for it
later is required anyway for such drives.
Lengthy delays can now be avoided by not configuring nonexistent
(ata) drives. Unfortunately, this breaks detection of atapi drives
in some configurations.
for passing in their own data space and associated page table information.
Update the support files so that any pages in the vm86 page table are
mapped, rather than just one page.
Restore the E820 memory probe, and have it use the new interface.
of private_tss, and there's no need to use a bit array. Also fixes
the problem of using `je' after btrl, since cmpl sets ZF.
Noticed by: Luoqi, on -current
switching video modes. People typically see the panic when the screen
saver has been running and is being stopped.
WARNING: this is not a real fix. Something really funny must be
happening in the page table entries for the physical memory
0x0-0xa0000, which is mapped to the beginning of the kernel region.
Use the pmap_kenter/pmap_kremove inline functions
instead of duplicating them.
pmap_remove_all:
Eliminate an unused (but initialized) variable.
pmap_ts_reference:
Change the implementation. The new implementation is much smaller
and simpler, but functionally identical. (Reviewed by
"John S. Dyson" <dyson@iquest.net>.)
bootblocks in order to boot the kernel after this! Also note that this
change breaks BSDI BSD/OS compatibility.
Also increased default NKPT to 17 so that FreeBSD can boot on machines
with >=2GB of RAM. Booting on machines with exactly 4GB requires other
patches, not included.
KBD_INSTALL_CDEV).
- Removed the note that the VESA option cannot be used on the SMP system;
this is not true.
- Moved the option VESA to more appropriate place.
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
config info. On early revision cards (742a), the EISA register space,
other than the location used to determine the address of the card's main
command ports, is write only.
to manage their own memory. Tested on my machine (make buildworld).
I've made analogous changes on the alpha, but don't have a machine
to test.
Not-objected-to by: dg, gibbs
numbers as chars or use bogus casts in an attempt to unmisrepresnt
them. In top, don't assume that 0xff is the only negative cpu
number when cpu numbers are (mis)represented.
a TLB invalidation optimization that won't work given the
limitations of our current SMP support.
This patch should be applied to -stable ASAP.
Thanks to John Capo <jc@irbs.com>,
Steve Kargl <sgk@troutmask.apl.washington.edu>, and
Chuck Robey <chuckr@mat.net>
for testing.
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
already defined. This allows for cross building to work because we
need to lie to make to tell it to use the target names rather than the
host names.
This should have no effect on either architecture. I've confirmed
that the intel build by make buildworld's for the past 3 months.
not per-process. Keep it in `switchtime' consistently.
It is now clear that the timestamp is always valid in fork_trampoline()
except when the child is running on a previously idle cpu, which
can only happen if there are multiple cpus, so don't check or set
the timestamp in fork_trampoline except in the (i386) SMP case.
Just remove the alpha code for setting it unconditionally, since
there is no SMP case for alpha and the code had rotted.
Parts reviewed by: dfr, phk
their ttl). This can be used - in combination with the proper ipfw
incantations - to make a firewall or router invisible to traceroute
and other exploration tools.
This behaviour is controlled by a sysctl variable (net.inet.ip.stealth)
and hidden behind a kernel option (IPSTEALTH).
Reviewed by: eivind, bde
This is for various Olicom cards. An IBM driver is following.
This patch also adds support to tcpdump to decode packets on tokenring.
Congratulations to the proud father.. (below)
Submitted by: Larry Lile <lile@stdio.com>
is the preparation step for moving pmap storage out of vmspace proper.
Reviewed by: Alan Cox <alc@cs.rice.edu>
Matthew Dillion <dillon@apollo.backplane.com>
put it, just like on the Alpha. It was wrong to load it at the
fixed address 0x08000000. That should only be done if the dynamic
linker is an executable (not a shared object) with a specific load
address encoded in the object file itself.
This fixes the recent breakage in the Linux emulator.
This makes it possible to change the sysctl tree at runtime.
* Change KLD to find and register any sysctl nodes contained in the loaded
file and to unregister them when the file is unloaded.
Reviewed by: Archie Cobbs <archie@whistle.com>,
Peter Wemm <peter@netplex.com.au> (well they looked at it anyway)
driver was thinking irq was enabled although it wasn't.
This case was particular to a no-interrupt static configuration.
Reported by: "Norman C. Rice" <nrice@emu.sourcee.com>
programs, including msdos, set PSL_NT in probes for old cpu types,
although PSL_NT doesn't do anything useful in vm86 or real mode.
PSL_NT is even less useful in the signal handlers. It just causes
T_TSSFLT faults on return from syscalls made by the handlers.
These faults are fixed up lazily so that Xsyscall() doesn't have
to be slowed down to prevent them. The fault handler recently
started complaining about these faults occurring "with interrupts
disabled". It should not have, but the complaints pointed to this
bug.
PR: 9211
when the process starts, and having it nonzero causes statically-linked
Linux binaries to fail.
PR: i386/10015
Submitted by: Marcel Moolenaar <marcel@scc.nl>
peripheral drivers can determine where in the devstat(9) list they are
inserted.
This requires recompilation of libdevstat, systat, vmstat, rpc.rstatd, and
any ports that depend on the devstat code, since the size of the devstat
structure has changed. The devstat version number has been incremented as
well to reflect the change.
This sorts devices in the devstat list in "more interesting" to "less
interesting" order. So, for instance, da devices are now more important
than floppy drives, and so will appear before floppy drives in the default
output from systat, iostat, vmstat, etc.
The order of devices is, for now, kept in a central table in devicestat.h.
If individual drivers were able to make a meaningful decision on what
priority they should be at attach time, we could consider splitting the
priority information out into the various drivers. For now, though, they
have no way of knowing that, so it's easier to put them in an easy to find
table.
Also, move the checkversion() call in vmstat(8) to a more logical place.
Thanks to Bruce and David O'Brien for suggestions, for reviewing this, and
for putting up with the long time it has taken me to commit it. Bruce did
object somewhat to the central priority table (he would rather the
priorities be distributed in each driver), so his objection is duly noted
here.
Reviewed by: bde, obrien
PQ_FREE. There is little operational difference other then the kernel
being a few kilobytes smaller and the code being more readable.
* vm_page_select_free() has been *greatly* simplified.
* The PQ_ZERO page queue and supporting structures have been removed
* vm_page_zero_idle() revamped (see below)
PG_ZERO setting and clearing has been migrated from vm_page_alloc()
to vm_page_free[_zero]() and will eventually be guarenteed to remain
tracked throughout a page's life ( if it isn't already ).
When a page is freed, PG_ZERO pages are appended to the appropriate
tailq in the PQ_FREE queue while non-PG_ZERO pages are prepended.
When locating a new free page, PG_ZERO selection operates from within
vm_page_list_find() ( get page from end of queue instead of beginning
of queue ) and then only occurs in the nominal critical path case. If
the nominal case misses, both normal and zero-page allocation devolves
into the same _vm_page_list_find() select code without any specific
zero-page optimizations.
Additionally, vm_page_zero_idle() has been revamped. Hysteresis has been
added and zero-page tracking adjusted to conform with the other changes.
Currently hysteresis is set at 1/3 (lo) and 1/2 (hi) the number of free
pages. We may wish to increase both parameters as time permits. The
hysteresis is designed to avoid silly zeroing in borderline allocation/free
situations.
to an architecture-specific value defined in <machine/elf.h>. This
solves problems on large-memory systems that have a high value for
MAXDSIZ.
The load address is controlled by a new macro ELF_RTLD_ADDR(vmspace).
On the i386 it is hard-wired to 0x08000000, which is the standard
SVR4 location for the dynamic linker.
On the Alpha, the dynamic linker is loaded MAXDSIZ bytes beyond
the start of the program's data segment. This is the same place
a userland mmap(0, ...) call would put it, so it ends up just below
all the shared libraries. The rationale behind the calculation is
that it allows room for the data segment to grow to its maximum
possible size.
These changes have been tested on the i386 for several months
without problems. They have been tested on the Alpha as well,
though not for nearly as long. I would like to merge the changes
into 3.1 within a week if no problems have surfaced as a result of
them.
(SVR4 does have it so that;s probably the cause of this bug)
2) Add a wrapper function for translation between ibcs2_ipc_perm and
ipc_perm as I think we screwed up when defining the ipc_perm struct and
mixed up 'normal' and creator [ug]id's
3) Fix IBCS2_IPC_STAT semctl. The FreeBSD version needs a union semun
whereas the IBCS2 version gives a struct ibcs2_semid_ds.
Apparently this is all fixed in the SVR4 compatibility code.
PR: 7729
with -aout. Added translation back to elf names in asnames.h as
usual. The elf names were inconsistent in the aout case even
internally because a macro adds an underscore to just one of them.
Removed commented out code for a previous life of `svr4_esigcode'.
Didn't add an underscore to `svr4_esigcode' since it is correct for
aout although wrong for elf, like most internal names in assembler
files. These names should be in a different namespace so that gprof
can ignore them.
Fixed some disorder in asnames.h.
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
structures" but since tty structs aren't malloced it is actually
mainly for tty-level (clist) buffers. It was slightly misused
here for com structs, and the previous commit completely misused
it for device buffers.
Fixed some bugs in nearby pccard code:
- memory leak when pccards go away (broken in previous commit).
- bogus bzeroing of the com struct before freeing it.
- style bugs.
the input speed, so that it can work at speeds larger than 115200
bps without being flow controlled. The buffer is twice as large
as before at 115200 bps and half as large as before at low speeds
Use a single interrupt-level buffer instead of ping-pong buffers
because the simplifications provided by ping-pong buffers became
complications.
This change is over-engineered. Statically configured buffering
was simpler and faster, and increasing the buffer size to support
1.5Mbps would cost about 1 US cent's worth of RAM per port, but I
was interested in the buffer switching mechanism.
panic during boot on machines with >=2GB of RAM. Also changed some
incorrect printf conversion specifiers from %d to %u (signed to unsigned).
This fixes bugs when printing the amount of memory on machines with >=2GB
of RAM.
/dev/urandom takes about 38 seconds on a P5/133. It is useful
to be able to kill such reads almost immediately. Processes
doing such reads are now scheduled so their denial of service
is no worse than that of processes looping in user mode.
Increase the overall length of the delay by 10.
Without this a 3C509 card on my MediaGX crash box can't be reliably
read. With this it is solid.
I've left a delay multiplier in instead of just changing the base
delay because I'm surprised I had to increase it so much and expect
there may be another problem.
Change microseq offsets. Previously, offsets of the program counter where
added to the index of the current microinstruction. Make them rely on the
index of the next executed microinstruction.
Suggested by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
Sun implemented iBCS2 compatibility on Solaris >= 2.6: The emulator
runs in user-mode, patching the LDT so that client programs making
syscalls through the old iBCS2 call gate get handled by the emulator
process. Unemulated syscalls therefore need their own call-gate that
bypasses the emulator. Sun chose LDT entry 4 to implement this, which
is what we've been using as LUDATA_SEL, so we need to change LUDATA_SEL
if we want to run Solaris executables.
Discussed with: Mike Smith
also a bit of a BDE patch in there I beleive. Backs out a fix I needed for Cyrix support
early on but it turns out that a later fix in the cyrix support made it un-needed.
This changes the definitions of a few items so that structures are the
same whether or not the option itself is enabled. This allows
people to enable and disable the option without recompilng the world.
As the author says:
|I ran into a problem pulling out the VM_STACK option. I was aware of this
|when I first did the work, but then forgot about it. The VM_STACK stuff
|has some code changes in the i386 branch. There need to be corresponding
|changes in the alpha branch before it can come out completely.
what is done:
|
|1) Pull the VM_STACK option out of the header files it appears in. This
|really shouldn't affect anything that executes with or without the rest
|of the VM_STACK patches. The vm_map_entry will then always have one
|extra element (avail_ssize). It just won't be used if the VM_STACK
|option is not turned on.
|
|I've also pulled the option out of vm_map.c. This shouldn't harm anything,
|since the routines that are enabled as a result are not called unless
|the VM_STACK option is enabled elsewhere.
|
|2) Add what appears to be appropriate code the the alpha branch, still
|protected behind the VM_STACK switch. I don't have an alpha machine,
|so we would need to get some testers with alpha machines to try it out.
|
|Once there is some testing, we can consider making the change permanent
|for both i386 and alpha.
|
[..]
|
|Once the alpha code is adequately tested, we can pull VM_STACK out
|everywhere.
|
Submitted by: "Richard Seaman, Jr." <dick@tar.com>
This takes the conditionals out of the code that has been tested by
various people for a while.
ps and friends (libkvm) will need a recompile as some proc structure
changes are made.
Submitted by: "Richard Seaman, Jr." <dick@tar.com>
