what the ACPI-safe workaround is intended to fix. Requested by phk.
Set the bushandle and tag when attaching the timer, don't do it each time
in read_counter(). Pointed out by bde.
Move test_counter() to the end. Staticize acpi_timer_reg.
of you with other cards, please do review and test the drivers for
MP-safety and disable Giant in the interrupt routines when you are
sure of proper functionality.
wireless ever since I added the new spinlock code. Previously, I added
a special ndis_rxeof_serial() function to insure that when we receive
a packet, we never end up calling the MiniportReturnPacket() routine
until after the receive handler has finished. I set things up so that
ndis_rxeof_serial() would only be used for serialized miniports since
they depend on this property. Well, it turns out deserialized miniports
depend on a similar property: you can't let MiniportReturnPacket() be
called from the same context as the receive handler at all. The 2100B
driver happens to use a single spinlock for all of its synchronization,
and it tries to acquire it both while in MiniportHandleInterrupt() and
in MiniportReturnPacket(), so if we call MiniportReturnPacket() from
the MiniportHandleInterrupt() context, we will end up trying to acquire
the spinlock recursively, which you can't do.
To fix this, I made the ndis_rxeof_serial() handler the default. An
alternate solution would be to make ndis_return_packet() submit
the call to MiniportReturnPacket() to the NDIS task queue thread.
I may do that in the future, after I've tested things a bit more.
supported. Symptoms of this bug included unnecessary use of ACPI-safe
and a dmesg that has deltas of about 2^24:
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 16777210, width = 16777208
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
To fix this:
* Use a 32 bit timecounter mask when the timer is 32 bits.
* In test_counter(), use the acpi_TimerDelta function which handles 24/32
bit timers and wraparound.
Miscellaneous fixes:
* Use C99 initializers for timecounter struct.
* Use u_int and uint32_t where appropriate instead of unsigned.
* Remove whitespace-only lines
* Remove the old PIIX4 PCI workaround. The timecounter testing code has
been in use for long enough to prove it's functional.
globally available. acpi_TimerDelta() subtracts two readings from the
ACPI PM timer and returns the difference. It properly distinguishes between
24-bit and 32-bit timers and handles wraparound.
a NULL crsbuf pointer. This shouldn't happen if it returns AE_OK. We'll
figure out why this is happening later.
Submitted by: Bruno Ducrot <ducrot@poupinou.org>
routine since the error will be reported back to the user buffer.
This will quiet down the bootverbose case when using an ACU which
does brute force discovery of the physical and logical devices.
of the struct, so that a placeholder for it (or unportable C99
initializers) are not needed for entries that don't use it. Use a C99
initializer for the 1 entry that uses it. Removed 91 placeholders.
This also restores API compatibility with NetBSD and RELENG_4 for most
entries.
Removed the requirement for a particular subvendor/subproduct in
rev.1.26 (VScom PCI-800L card). While the BARs, etc., may depend on
the sub-ids, this is not known to be so, and I think it is better to
guess that they don't. The decision to check sub-id checks in this
file is apparently random; for VScom cards they were checked in 3 of
8 cases.
Reviewed by: timeout by committer (joerg) after 6 months
Nehemiah chip, but the work is all done in hardware.
There are three opportunities to add other entropy; the Data
Buffer, the Cipher's IV and the Cipher's key. A future commit
will exploit these opportunities.
Logical volumes on these devices show up as LUNs behind another
controller (also known as proxy controller). In order to issue
firmware commands for a volume on a proxy controller, they must be
targeted at the address of the proxy controller it is attached to,
not the Host/PCI controller.
A proxy controller is defined as a device listed in the INQUIRY
PHYSICAL LUNS command who's L2 and L3 SCSI addresses are zero. The
corresponding address returned defines which "bus" the controller
lives on and we use this to create a virtual CAM bus.
A logical volume's addresses first byte defines the logical drive
number. The second byte defines the bus that it is attached to
which corresponds to the BUS of the proxy controller's found or the
Host/PCI controller.
Change event notification to be handled in its own kernel thread.
This is needed since some events may require the driver to sleep
on some operations and this cannot be done during interrupt context.
With this change, it is now possible to create and destroy logical
volumes from FreeBSD, but it requires a native application to
construct the proper firmware commands which is not publicly
available.
Special thanks to John Cagle @ HP for providing remote access to
all the hardware and beating on the storage engineers at HP to
answer my questions.
uiomove(9) is not properly locked. So, return to NEEDGIANT
mode. Later, when uiomove is finely locked, I'll revisit.
While I'm here, provide some temporary debugging output to
help catch blocking startups.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
