after the first found, if multiple LUNs are tried.
Change probe message to just the SCSI chip id,
similar to what the NCR driver prints.
Change the driver name to "amd" in all places.
Thanks to Nick Sayer <nsayer@quack.kfu.com> for
doing some debugging, for sending a boot message
log that shows the driver is functional, and for
pointing out there still were places that needed
the driver name to be corrected.
was found, or if there was a checksum mismatch.
This patch should allow the driver to be used with any AMD 53c974
based SCSI card, or with the AMD SCSI+Ethernet Combo Chip found on
some motherboards.
These controllers are based on the AMD 53c974, and the driver
does only support those two cards, since it checks for a Tekram
specific configuration EEPROM.
This deficiency (TM) will be fixed soon ... :)
This code is:
(C)Copyright 1995-1996 Tekram Technology Co., Ltd.
Obtained from: Tekram
Tekram DC390W/U/F, whose config EEPROM can now be dumped, if the kernel
is built with option NCR_TEKRAM_EEPROM.
Other changes:
- add brackets to expansion of OUTB/W/L macro arguments.
- remove unused NCB structure element ns_async
- support sync. SCSI offset of 16 (instead of only 8) on 825A and 875
- correctly identify 53c810A and 53c825A chips
- preserve SCSI BIOS settings of PCI performance options
- remove (already disabled) support for NCR reset because of command timeout
- reverse order of reading of SCSI and DMA specific interrupt cause registers
- add definition of Tekram config EEPROM contents (not currently used)
I've added an installation from optical disk drive facility.
This enables FreeBSD to be installed from an optical disk, which
may be formatted in "super floppy" style or sliced into MSDOS-FS
and UFS partitions.
Note: ncr.c should be reviewed by Stefan Esser <se@freebsd.org>
and cd.c by Joerg Wunsch <joerg@freebsd.org> before bringing this
into 2.2.
Submitted-By: Shunsuke Akiyama <akiyama@kme.mei.co.jp>
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
1. 'connector_table' is shortened to 'conn_tab'.
2. More reliable connector change code.
3. Display message like "vx0: selected bnc. (link1)"
when the connector changed by link[012].
4. Handle MII properly.
5. Potentially slightly better performance.
6. Fixed a silly typo.
Submitted by: Naoki Hamada <nao@sbl.cl.nec.co.jp>
a) Removal of private typedefs tulip_uint*_t, use standard u_int_*_t.
b) Change [Dd][Cc]21.4. to just 21.4., seems Dec has done this to all
of the drivers for all OS's. (Did they get in trouble with someone?)
[The few that remain can either not be eliminated, or are waiting for
additional driver functional changes that will remove them.]
c) Move some code from dc21040.h into the driver, later a whole block of that
code and more will move to devar.h, but for now this makes it easier
to study diffs.
d) Add a big bold comment to the README.de file about it not reflecting
reality anymore.
Note that these are all cosmetic changes and should be no functional
change in the driver whatsoever. If _anyone_ spots a problem introduced
by this please let me know ASAP!
wdreg.h: Delete wd_ctlr macro. PC98 version of wd.c treats it as a
variable.
GENERIC98: Delete ep0 entry. Current ep driver write I/O port 0x100.
This clobbers ICW of i8259, because upper 8bits of address line is not
masked on mother board.
if_fe.c: Merge from revision 1.18 of sys/i386/isa/if_fe.c.
pc98.c: Globalize dmapageport, because SCSI driver use this
variable.
wd82371.c: Yet another merge.
These are 2.2 candidates.
Submitted by: The FreeBSD(98) Development Team
bridges with support for 64 bit memory addresses and 32 bit I/O addresses).
The code is not complete. It ignores the upper half of the long addresses.
This is not a problem on PC compatible systems, but has to be fixed for
real computers.
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
Be smart about the STPWEN control bit in SCFRCTL1. It should only be set
if the low byte of the bus is to be terminated. We figure this out either
by "caching" the value left over from the BIOS setup before we reset the card
or by using the values stored in the seeprom if it is availible.
This follows more closely the suggestions in the latest NCR docs, and has
been running on my system for weeks with no problem. It does improve the
quality of diagnostic messages and does allow to better understand the
sequence of events in case of an error.
This should go into 2.2 and 2.1.6.
7810 being either the last of the first device to be probed, so use a counting
scheme instead to determine when one card ends and another begins. There may
be a better way to do this by decoding the PCI tag, which I will investigate
later.
2.2 Candidate.
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, nao@tom-yam.or.jp (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly nao@tom-yam.or.jp (HAMADA Naoki)
Obtained from:partly OpenBSD
This involves expanding the support of the SEEPROM routines to deal with
the larger SEEPROMs on these cards and providing a mechanism to share
SCB arrays between multiple controllers.
Most of the 398X support came from Dan Eischer.
ahc_data -> ahc_softc
Clean up some more type bogons I missed from the last pass.
Garrett Wollman sent me this code a few weeks ago for review, and I made
some significant changes, which he in turn accepted ...
In order to make use of these changes, a device entry has to added to /dev.
Submitted by: wollman
<net/if_arp.h> and fixed the things that depended on it. The nested
include just allowed unportable programs to compile and made my
simple #include checking program report that networking code doesn't
need to include <sys/socket.h>.
Still no support for Ultra-SCSI and other new features, but the code
should now correctly initialize the clock pre-scaler (based on freqency
measurement results, if necessary).
Fix support of 16 targets for WIDE SCSI.
Disable bus reset in case no progress is made for too long ("ncr dead"
message), which did not work too well with scanners and other slow devices.
not resuming the NIC as required for transmit. Thanks to Alan Cox
<alc@cs.rice.edu> for noticing this.
Added another performance optimization to compensate. :-)
Changed crscdt to 1...strange, but this seems to be needed for some reason
despite what the manual says.
ring that caused wrong things to happen sometimes.
Doubled the number of transmit descriptors to 128 so that the internal
FIFO in the NIC can be fully filled when dealing with small packets.
Several minor performance improvements.
