Story so fr:
1) PPP on-demand with static IP works.
2) PPP on-demand with dynamic IP says "Host is down" on any IP request
The problem is that tun driver check its READY state by *first* ifconfig address.
i.e.:
set ifaddr <addr> <addr2>
works (static IP) and
set ifaddr 0 <addr2>
not works (dynamic IP) because first address is equal 0.
Since tun is always POINTOPOINT interface, dst address is more meaningfull.
I change checking to second (dst) address in READY test.
PPP on-demand finally works.
- fill in and use ifp->if_softc
- use if_bpf rather than private cookie variables
- change bpf interface to take advantage of this
- call ether_ifattach() directly from Ethernet drivers
- delete kludge in if_attach() that did this indirectly
and rmx_recvpipe. This has no demonstrable effect on performance.
(ttcp reports about 44 Mbit/s for all the buffer sizes I tried between
16384 and 65536.)
of limited utility. In their place, add bunch of pointers
which will eventually be needed by the polled-interrupt scheme we're working
here. (It will probably be a while before the code is written and
committed here.) At the same time, a `void *if_softc' field
was added to the beginning of the structure to make certain driver
writers happier.
The practical upshot of all this is that you need to
recompile utilities such as netstat which manipulate struct ifnet.
others: start to populate the link-layer branch of the net mib, by
moving ARP to its proper place. (ARP is not a protocol family, it's an
interface layer between a medium-access layer and a protocol family.)
sysctl(8) needs to be taught about the structure of this branch, unless
Poul-Henning implements dynamic MIB exploration soon.
*' instead of caddr_t and it isn't optional (it never was). Most of the
netipx (and netns) pr_ctlinput functions abuse the second arg instead of
using the third arg but fixing this is beyond the scope of this round
of changes.
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
Declared dsioctl() as static consistently. Note that both if_disc.c
and subr_diskslice.c use the same prefix `ds' and there is a name
conflict for dsioctl().
Protected them with `#ifdef KERNEL' so that <sys/queue.h> is valid C++.
Added the necessary #includes of <sys/queue.h>.
These functions are bogus and should be replaced by the queue macros.
That's EVERY SINGLE driver that has an entry in conf.c..
my next trick will be to define cdevsw[] and bdevsw[]
as empty arrays and remove all those DAMNED defines as well..
Each of these drivers has a SYSINIT linker set entry
that comes in very early.. and asks teh driver to add it's own
entry to the two devsw[] tables.
some slight reworking of the commits from yesterday (added the SYSINIT
stuff and some usually wrong but token DEVFS entries to all these
devices.
BTW does anyone know where the 'ata' entries in conf.c actually reside?
seems we don't actually have a 'ataopen() etc...
If you want to add a new device in conf.c
please make sure I know
so I can keep it up to date too..
as before, this is all dependent on #if defined(JREMOD)
(and #ifdef DEVFS in parts)
is acknowledged, it should go to the lcp ack sent state.
Don't reply on lcp echo requests when not in the lcp opened state.
If the interface is set to CISCO mode, it should still be marked
running when ifconfiged.
Fixed a few indentations that had gone wrong somewhere.
Submitted-by: John.Hay@csir.co.za
Note that pppd doesn't have an ipxcp.c module for negotiating and confuguring
IPX at startup, but after these mods, you can manually ifconfig IPX addresses
on the interface and it will probably work.. :-)
These functions went away:
enosys (hasn't been used for some time)
enxio
enodev
enoioctl (was used only once, actually for a vop)
if_tun.c:
Continued cleaning up...
conf.h:
Probably fixed the type of d_reset_t. It is hard to tell the correct
type because there are no non-dummy device reset functions.
Removed last vestige of ambiguous sleep message strings.
by functions.
tty_conf.c:
Cleaned up formatting of tables.
Removed another ARGSUSED for consistency.
conf.h:
Introduced typedefs for line discipline functions.
Backed out most of previous revision (it is done elsewhere).
to <machine/conf.h>. conf.h was mechanically generated by
`grep ^d_ conf.c >conf.h'. This accounts for part of its ugliness. The
prototypes should be moved back to the driver sources when the functions
are staticalized.
if_sl and if_ppp (from ppp-2.2), eliminating the nearly identical
pppcompress.[ch] code. Add maximum VJ compression states argument to
sl_compress_init().
if_sl: call sl_compress_init() with the extra argument.
Submitted by: Mike Mitchell, supervisor@alb.asctmd.com
This is a bulk mport of Mike's IPX/SPX protocol stacks and all the
related gunf that goes with it..
it is not guaranteed to work 100% correctly at this time
but as we had several people trying to work on it
I figured it would be better to get it checked in so
they could all get teh same thing to work on..
Mikes been using it for a year or so
but on 2.0
more changes and stuff will be merged in from other developers now that this is in.
Mike Mitchell, Network Engineer
AMTECH Systems Corporation, Technology and Manufacturing
8600 Jefferson Street, Albuquerque, New Mexico 87113 (505) 856-8000
supervisor@alb.asctmd.com
ifp->if_output() functions. This way, initial implementations of
rt_output functionality can just lazily use if_output until customized
versions are written.
