the virtio backends.
- Add a new ioctl to export the count of pins on the I/O APIC from vmm
to the hypervisor.
- Use pins on the I/O APIC >= 16 for PCI interrupts leaving 0-15 for
ISA interrupts.
- Populate the MP Table with I/O interrupt entries for any PCI INTx
interrupts.
- Create a _PRT table under the PCI root bridge in ACPI to route any
PCI INTx interrupts appropriately.
- Track which INTx interrupts are in use per-slot so that functions
that share a slot attempt to distribute their INTx interrupts across
the four available pins.
- Implicitly mask INTx interrupts if either MSI or MSI-X is enabled
and when the INTx DIS bit is set in a function's PCI command register.
Either assert or deassert the associated I/O APIC pin when the
state of one of those conditions changes.
- Add INTx support to the virtio backends.
- Always advertise the MSI capability in the virtio backends.
Submitted by: neel (7)
Reviewed by: neel
MFC after: 2 weeks
/dev/kmem and related devices (i.e. grants PRIV_IO and PRIV_KMEM_WRITE).
This in conjunction with changing the drm driver's permission check from
PRIV_DRIVER to PRIV_KMEM_WRITE will allow a jailed Xorg server.
Submitted by: netchild
MFC after: 1 week
- Use system provided functions for HID report requests.
- Nice the mode setting, because the USB hardware does appear to
handle the commands right away.
MFC after: 1 week
swcr_newsession can change the pointer for swcr_sessions which races with
swcr_process which is looking up entries in this array.
Add a rwlock that protects changes to the array pointer so that
swcr_newsession and swcr_process no longer race.
Original patch by: Steve O'Hara-Smith <Steve.OHaraSmith@isilon.com>
Reviewed by: jmg
Sponsored by: EMC / Isilon Storage Division
By definition, the very first FIN is not a duplicate. Process it normally
and don't feed it to congestion control as though it were a dupe. Don't
prevent CC from seeing later dupe acks while in a half close state.
the memory ranges that they decode for downstream devices rather than
creating ResourceProducer range resource entries. The result is that
we allocate the full range to the PCI root bridge device causing
allocations in child devices to all fail.
As a workaround, ignore any standard memory resources on a PCI root
bridge device. It is normal for a PCI root bridge to allocate an I/O
resource for the I/O ports used for PCI config access, but I have not
seen any PCI root bridges that legitimately allocate a memory resource.
Reviewed by: jkim
MFC after: 1 week
the INP_INFO lock from tcp_usr_accept. As the PR/patch states
this was following the advice already in the code.
See the PR below for a full disucssion of this change and its
measured effects.
PR: 183659
Submitted by: Julian Charbon
Reviewed by: jhb
The ext4 inode flags do not have equivalents for chflags (1)
and hold information that is private to the implementation.
The i_flag field in the inode is a better place to hold the Ext4
inode flags as it saves us from masking flags while setting or
getting attributes. It should also make things cleaner if we
implement write support for Ext4.
Suggested by: bde
Tested by: Mike Ma
MFC after: 3 days
that all pressed keys are released before completing the USB keyboard
detach. This will prevent so-called "ghost-keys" from appearing after
that the USB device generating the key event(s) has been detached.
MFC after: 1 week
It's common for multi-threaded processes to create a thread for
the purpose of synchronously processing signals. Allow such processes to
utilize a capabilities sandbox.
Discussed with: rwatson, pjd
MFC after: 2 weeks
when activating an I/O or memory window on the CardBus bridge.
Tested by: Olivier Cochard-Labbe <olivier@cochard.me>
Reviewed by: imp
MFC after: 3 days
Note that this commit hasn't been compile tested because these files
are not hooked up to the build...
PR: 186129
Submitted by: Takanori Sawada
Approved by: rpaulo
The VMCS field EOI_bitmap[] is an array of 256 bits - one for each vector.
If a bit is set to '1' in the EOI_bitmap[] then the processor will trigger
an EOI-induced VM-exit when it is doing EOI virtualization.
The EOI-induced VM-exit results in the EOI being forwarded to the vioapic
so that level triggered interrupts can be properly handled.
Tested by: Anish Gupta (akgupt3@gmail.com)
The IN_* flags should be set in i_flag instead of corrupting
i_flags [1].
Re-enable HTree dirindex as the last series of bug fixes
seems to have fixed the issues.
Reported by: bde [1]
Tested by: kevlo
MFC after: 1 week
macro was changed. Since copying 64-bit srr1 into 32-bit srr1 drops the upper
32 bits, any bits set in the context were dropped, meaning the context check
fails. Since 32-bit set_context can't change those bits anyway, copy the ones
from the current context (td->td_frame) before calling set_context().
MFC after: 3 weeks
geom_alloc_copyin() can't return ENOMEM, so describe its fail as bad
control request. Add check for NULL pointer in gctl_dump(), since it
can be NULL when geom_alloc_copyin() failed.
MFC after: 1 week
Add to the gctl_error() an ability to specify error description even
if numeric error code is already specified. Also by default set
error code to EINVAL.
PR: 185852
MFC after: 1 week
injected into the vcpu but the VM-entry interruption information field
already has the valid bit set.
Pointed out by: David Reed (david.reed@tidalscale.com)
The latest draft of SBC-3 tells: "A MAXIMUM UNMAP LBA COUNT field set to
a non-zero value indicates the maximum number of LBAs that may be unmapped
by an UNMAP command." To me it does not sound like that limit is set per
single descriptor, but rather per all command. And I have at least one
device that behaves exactly that way. This patch fixes the problem there.
MFC after: 1 week
Make comments match parameters
Add options for early printf so we get regression build testing on it.
Add preview of options for FDT support coming soon (I hope)
paper trail now, this patch is similar to one posted for one of the
preliminary versions of a new armv6 port. I took them and made them
more generic. Option not enabled by default since each board/port has
to provide its own eputc, and possibly do other things as well...
Use the bitwise negation instead of bogus boolean negation and move
the flag manipulation with the assignment.
Fix some grammatical errors introduced in the same change.
Reported by: bde
MFC after: 3 days
pim_input() properly.
While here, remove extra variable and incorrect condition
before m_pullup().
Reported by: Olivier Cochard-Labbé <olivier cochard.me>
Sponsored by: Nginx, Inc.
a timeout value of a single tick is given. With FreeBSD-10 and newer
the current system time is used as a starting point, and the minimum
callout time of a single tick will be guaranteed. This patch mostly
affect the DMA delay timeouts, which are typically in the range from
0.125 to 2ms.
MFC after: 1 week
via a software interrupt.
This is safe to do because the logical processor is already cognizant of the
NMI and further NMIs are blocked until the host's NMI handler executes "iret".
r260545 cleared the inode flags to fix corruption problems but
we still need to pass some EXT4 flags for the ext4 read-only
mode. None of these attributes has an equivalent in FreeBSD and
are uninteresting for the system utilities so they should be
innaccessible in ext2_getattrib().
Note: we also use EXT4_HUGE_FILE but we use it directly from the
dinode structure so it is not necessary to translate it,
Suggested by: bde
MFC after: 3 days
This is the first step needed to get the snapper codec working on those
machines.
The second step is to enable the corresponding I2S device and its clock.
Tested on machines where the snapper codec was already working, a G4 PowerBook
and a PowerMac9,1 with a Shasta based macio.
The PowerMac7,2/7,3 with a K2 based macio can now also play sound.
MFC after: 1 month
- Store the length of each read-only VPD value since not all values are
guaranteed to be ASCII values (though most are).
- Add a new pciio ioctl to fetch VPD for a single PCI device. The values
are returned as a list of variable length records, one for the device
name and each keyword.
- Add a new -V flag to pciconf's list mode which displays VPD data for
each device.
MFC after: 1 week
fence. Under system load, the CPU has been found to change the order
by which the stores are made visible. When the tag is made visible
before the other TLB values, other CPUs may use the invalid TLB values
and do bad things.
While here (i.e. not a fix) don't return errors from pmap_remove_vhpt()
to callers of pmap_remove_pte(). Those callers don't check the return
value and as such don't do what is needed to keep a consistent state.
More importantly, pmap_remove_vhpt() can't really have an error without
it indicating something unintended. Using KASSERT is therefore better.
PR: 182999, 183227
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.
Should have been part of r260889, but waasn't due to command line typo.
Reviewed by: bde (with reservations)
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.
Reviewed by: bde (with reservations)
* Set ia address/mask values BEFORE attaching to address lists.
Inet6 address assignment is not atomic, so the simplest way to
do this atomically is to fill in ia before attach.
* Validate irfa->ia_addr field before use (we permit ANY sockaddr in old code).
* Do some renamings:
in6_ifinit -> in6_notify_ifa (interaction with other subsystems is here)
in6_setup_ifa -> in6_broadcast_ifa (LLE/Multicast/DaD code)
in6_ifaddloop -> nd6_add_ifa_lle
in6_ifremloop -> nd6_rem_ifa_lle
* Split working with LLE and route announce code for last two.
Add temporary in6_newaddrmsg() function to mimic current rtsock behaviour.
* Call device SIOCSIFADDR handler IFF we're adding first address.
In IPv4 we have to call it on every address change since ARP record
is installed by arp_ifinit() which is called by given handler.
IPv6 stack, on the opposite is responsible to call nd6_add_ifa_lle() so
there is no reason to call SIOCSIFADDR often.
ia64 for the very first time. Only 9 years in the making...
Note that the vt/vga driver does not actually make sure there's
VGA hardware at the standard/legacy VGA I/O port and memory I/O
addresses. This can cause machine checks if the H/W does not have
a VGA controller.
of a syncache connection, copy it into the inp_flowid field.
Without this, an incoming TCP connection won't have an inp_flowid marked
until some data comes in, and this means that things like the per-CPU
TCP timer option will choose a different CPU for the timer work.
(It also means that if one grabbed the flowid via an ioctl from userland,
it won't be available until some data has been received.)
Sponsored by: Netflix, Inc.
callback providers. link_init_sdl() function can be used to
fill most of the parameters. Use caller stack instead of
allocation / freing memory for each request. Do not drop support
for extra-long (probably non-existing) link-layer protocols by
introducing link_alloc_sdl() (used by if_resolvemulti() callback)
and link_free_sdl() (used by caller).
Since this change breaks KBI, MFC requires slightly different approach
(link_init_sdl() auto-allocating buffer if necessary to handle cases
with unmodified if_resolvemulti() callers).
MFC after: 2 weeks
the Guest Interruptibility-state field. However, there isn't any way to
figure out which processors have this requirement.
So, inject a pending NMI only if NMI_BLOCKING, MOVSS_BLOCKING, STI_BLOCKING
are all clear. If any of these bits are set then enable "NMI window exiting"
and inject the NMI in the VM-exit handler.
1. Be consistent in the style of "act_delta" manipulations between the
inactive and active queue scans.
2. Explicitly compare to zero.
3. The deactivation of a page is based is based on its recent history
and not just the current call to vm_pageout_scan(). The variable
"act_delta" represents the current state of the page, and not its
history. Avoid possible confusion by not (ab)using "act_delta" for
the making the deactivation decision.
Submitted by: kib [1]
Reviewed by: kib [2,3]
with USB device detach when using character device handles. This also
includes LibUSB. It turns out that "usb_close()" cannot always get a
reference to clean up its USB transfers and such, if called during the
kernel USB device detach.
Analysis by: hselasky @
Reported by: Juergen Lock <nox@jelal.kn-bremen.de>
MFC after: 1 week
This is done to ensure that visited object IDs are always increasing.
Also, pass correct object ID to prefetch_dnode_metadata for
os_groupused_dnode.
Without this change we would hit an assert if traversal was paused on
a GROUPUSED object, which is unlikely but possible.
Apparently the same change was independently developed by Deplhix.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
MFC after: 10 days
Sponsored by: HybridCluster
This fires off a kqueue note (of type sendfile) to the configured kqfd
when the sendfile transaction has completed and the relevant memory
backing the transaction is no longer in use by this transaction.
This is analogous to SF_SYNC waiting for the mbufs to complete -
except now you don't have to wait.
Both SF_SYNC and SF_KQUEUE should work together, even if it
doesn't necessarily make any practical sense.
This is designed for use by applications which use backing cache/store
files (eg Varnish) or POSIX shared memory (not sure anything is using
it yet!) to know when a region of memory is free for re-use. Note
it doesn't mark the region as free overall - only free from this
transaction. The application developer still needs to track which
ranges are in the process of being recycled and wait until all
pending transactions are completed.
TODO:
* documentation, as always
Sponsored by: Netflix, Inc.
This is still under a bit of flux, as the final API hasn't been nailed
down. It's also unclear whether we should define the two new types in the
header or not - it may allow bad code to compile that shouldn't (ie,
since uintX's are defined, the developer may not include sys/types.h.)
Reviewed by: peter, imp, bde
Sponsored by: Netflix, Inc.
in the Guest Interruptibility-state VMCS field.
If we fail to do this then a subsequent VM-entry will fail because it is an
error to inject an NMI into the guest while "NMI Blocking" is turned on. This
is described in "Checks on Guest Non-Register State" in the Intel SDM.
Submitted by: David Reed (david.reed@tidalscale.com)
The bug was introduced in r256956 "Improve ZFS N-way mirror read
performance".
The code in vdev_mirror_dva_select erroneously considers already
tried DVAs for the next attempt. Thus, it is possible that a failing DVA
would be retried forever.
As a secondary effect, if the attempts fail with checksum error, then
checksum error reports are accumulated until the original request
ultimately fails or succeeds. But because retrying is going on indefinitely
the cheksum reports accumulation will effectively be a memory leak.
Reviewed by: gibbs
MFC after: 13 days
Sponsored by: HybridCluster
If we prematurely free the name buffer and it gets quickly recycled,
then zfs_rename may see data from another lookup or even unmapped memory
via cn_nameptr.
MFC after: 6 days
Sponsored by: HybridCluster
The bug was introduced in r256956 "Improve ZFS N-way mirror read
performance".
The code in vdev_mirror_dva_select erroneously considers already
tried DVAs for the next attempt. Thus, it is possible that a failing DVA
would be retried forever.
As a secondary effect, if the attempts fail with checksum error, then
checksum error reports are accumulated until the original request
ultimately fails or succeeds. But because retrying is going on indefinitely
the cheksum reports accumulation will effectively be a memory leak.
Reviewed by: gibbs
MFC after: 13 days
Sponsored by: HybridCluster
Otherwise we could run into the following deadlock.
A thread has a transaction open and assigned to a transaction group.
That would prevent the transaction group from be quiesced and synced.
The thread is blocked in getnewvnode_reserve waiting for a vnode to
a be reclaimed. vnlru thread is blocked trying to enter ZFS VOP because
a filesystem is suspended by an ongoing rollback or receive operation.
In its turn the operation is waiting for the current transaction group
to be synced.
zfs_zget is always used outside of active transactions, but zfs_mknode
is always used in a transaction context. Thus, we hoist
getnewvnode_reserve from zfs_mknode to its callers.
While there, assert that ZFS always calls getnewvnode while having
a vnode reserved.
Reported by: adrian
Tested by: adrian
MFC after: 17 days
Sponsored by: HybridCluster
Problem case:
Original lookup returns route with GW set, so gw points to
rte->rt_gateway.
After that we're changing dst and performing lookup another time.
Since fwd host is most probably directly reachable, resulting
rte does not contain rt_gateway, so gw is not set. Finally, we
end with packet transmitted to proper interface but wrong
link-layer address.
Found by: lstewart
Discussed with: ae,lstewart
MFC after: 2 weeks
Sponsored by: Yandex LLC
add separate rx/tx ring indexes
add ring specifier in nm_open device name
netmap.c, netmap_vale.c
more consistent errno numbers
netmap_generic.c
correctly handle failure in registering interfaces.
tools/tools/netmap/
massive cleanup of the example programs
(a lot of common code is now in netmap_user.h.)
nm_util.[ch] are going away soon.
pcap.c will also go when i commit the native netmap support for libpcap.
sure to clear the lower 12 bits. We're adding the translation
attributes to the physical address and non-zero bits in the first
12 bits would give us something unexpected, including invalid bit
values. Those trigger nested general protection faults.
We do not have to clear the region bits, because they are ignored
anyway, so we can replace an existing dep instruction with the one
we need.
This fixes GP faults for the swapper thread, as it's the only thread
that has a direct-mapped stack. Since the bug is in the nested TLB
fault handler, the frequency of hitting the GP is in the order of
hours/days under load.
non-modifier key press. This prevents so-called "ghost
keyboards" keeping modifier keys pressed while not
actually seen as a real keyboard.
MFC after: 2 weeks
can be initiated in the context of a vcpu thread or from the bhyve(8) control
process.
The first use of this functionality is to update the vlapic trigger-mode
register when the IOAPIC pin configuration is changed.
Prior to this change we would update the TMR in the virtual-APIC page at
the time of interrupt delivery. But this doesn't work with Posted Interrupts
because there is no way to program the EOI_exit_bitmap[] in the VMCS of
the target at the time of interrupt delivery.
Discussed with: grehan@
found in High Speed USB HUBs which translate from High Speed USB into
FULL or LOW speed USB. In some rare cases SPLIT transactions might get
lost, which might leave the TT in an unknown state. Whenever we detect
such an error try to issue either a clear TT buffer request, or if
that is not possible reset the whole TT.
MFC after: 1 week
vm_pageout_scan(). There were missing increments in two less common cases.
Don't conflate the count of stuck pages and the pageout deficit provided by
vm_page_alloc{,_contig}(). (A proposed fix to the OOM code depends on this.)
Handle held pages consistently in the inactive queue scan. In the more
common case, we did not move the page to the tail of the queue. Whereas, in
the less common case, we did. There's no particular reason to move the page
in the less common case, so remove it.
Perform the calculation of the page shortage for the active queue scan a
little earlier, before the active queue lock is acquired. The correctness
of this calculation doesn't depend on the active queue lock being held.
Eliminate a redundant variable, "pcount". Use the more descriptive
variable, "maxscan", in its place.
Apply a few nearby style fixes, e.g., eliminate stray whitespace and excess
parentheses.
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
originally.
I am not sure why exactly have I moved it during one of many refactorings
during camlock project, but obviously it opens race window that may cause
use after free panics during SIM (in reported cases umass(4)) detach.
MFC after: 2 weeks
LibAliasSetAddress() uses its own mutex to serialize changes.
While here, convert ifp->if_xname access to if_name() function.
MFC after: 2 weeks
Sponsored by: Yandex LLC
After r252890 we are naively attempting to pass through the
inode flags. This is technically incorrect as the ext2
inode flags don't match the UFS/system values used in
FreeBSD and a clean conversion is needed.
Some filtering was left in place so the change didn't cause
significant changes in FreeBSD but some of the garbage passed
is likely to be the cause for warning messages in linux.
Fix the issue by resetting the flags before conversion as was
done previously. This also means we will not pass the EXT4_*
inode flags into FreeBSD's inode.
PR: kern/185448
MFC after: 3 days
controller found in the MBP2013 has been observed to not work properly
unless this operation is performed.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
inject interrupts into the guest without causing a VM-exit.
This feature can be disabled by setting the tunable "hw.vmm.vmx.use_apic_pir"
to "0".
The following sysctls provide information about this feature:
- hw.vmm.vmx.posted_interrupts (0 if disabled, 1 if enabled)
- hw.vmm.vmx.posted_interrupt_vector (vector number used for vcpu notification)
Tested on a Intel Xeon E5-2620v2 courtesy of Allan Jude at ScaleEngine.
This control is needed to enable "Posted Interrupts" and is present in all
the Intel VT-x implementations supported by bhyve so enable it as the default.
With this VM-exit control enabled the processor will acknowledge the APIC and
store the vector number in the "VM-Exit Interruption Information" field. We
now call the interrupt handler "by hand" through the IDT entry associated
with the vector.
Fix geom_uncompress(4) module loading. Don't link zlib.c (which is a module
itself) directly.
The built module was verified and used to read a few mkulzma(8) images on
amd64 to validate some of the informations on the manual page.
While here, don't overwrite CFLAGS.
Reviewed by: ray
Approved by: adrian (mentor)
make CAM to not try negotiate unsupported settings and suppress warnings.
While there, enable command queuing on pass-through devices, announced
in hba_inquiry, but disabled. Even though queue size is very small, It
seems working well enough.
Reviewed by: scottl
MFC after: 2 weeks
has the same prefix as some other alias on the same interface, use
newly-added rt_addrmsg() instead of hand-rolled in_addralias_rtmsg().
This eliminates the following rtsock messages:
Pinned RTM_ADD for prefix (for alias addition).
Pinned RTM_DELETE for prefix (for alias withdrawal).
Example (got 10.0.0.1/24 on vlan4, playing with 10.0.0.2/24):
before commit, addition:
got message of size 116 on Fri Jan 10 14:13:15 2014
RTM_NEWADDR: address being added to iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
got message of size 192 on Fri Jan 10 14:13:15 2014
RTM_ADD: Add Route: len 192, pid: 0, seq 0, errno 0, flags:<UP,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK>
10.0.0.0 10.0.0.2 (255) ffff ffff ff
after commit, addition:
got message of size 116 on Fri Jan 10 13:56:26 2014
RTM_NEWADDR: address being added to iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 14.0.0.2 14.0.0.255
before commit, wihdrawal:
got message of size 192 on Fri Jan 10 13:58:59 2014
RTM_DELETE: Delete Route: len 192, pid: 0, seq 0, errno 0, flags:<UP,PINNED>
locks: inits:
sockaddrs: <DST,GATEWAY,NETMASK>
10.0.0.0 10.0.0.2 (255) ffff ffff ff
got message of size 116 on Fri Jan 10 13:58:59 2014
RTM_DELADDR: address being removed from iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
adter commit, withdrawal:
got message of size 116 on Fri Jan 10 14:14:11 2014
RTM_DELADDR: address being removed from iface: len 116, metric 0, flags:
sockaddrs: <NETMASK,IFP,IFA,BRD>
255.255.255.0 vlan4:8.0.27.c5.29.d4 10.0.0.2 10.0.0.255
Sending both RTM_ADD/RTM_DELETE messages to rtsock is completely wrong
(and requires some hacks to keep prefix in route table on RTM_DELETE).
I've tested this change with quagga (no change) and bird (*).
bird alias handling is already broken in *BSD sysdep code, so nothing
changes here, too.
I'm going to MFC this change if there will be no complains about behavior
change.
While here, fix some style(9) bugs introduced by r260488
(pointed by glebius and bde).
Sponsored by: Yandex LLC
MFC after: 4 weeks
included.. netstat uses -DKERNEL=1 to get these parts and breaks the
build w/o it...
melifaro@ says that ae@ is probably asleep, and the PR doesn't have
this part of the patch... Probably a local change got in by accident..
PR: 185148
Pointy hat to: ae@
CFLAGS.clang in sys/conf/Makefile.arm, since the main kernel build does
not use <bsd.sys.mk>. So revert that particular change for now.
Pointy hat to: me
Noticed by: zbb
MFC after: 3 days
X-MFC-With: r259730
and invoke it for bootverbose logging, and also from a new DDB command,
"show devmap". Also tweak the format string for the bootverbose output
of physical memory chunks to get the leading zeros in the hex values.
Adding/deleting interface addresses involves access to 3 different subsystems,
int different parts of code. Each call can fail, so reporting successful
operation by rtsock in the middle of the process error-prone.
Further split routing notification API and actual rtsock calls via creating
public-available rt_addrmsg() / rt_routemsg() functions with "private"
rtsock_* backend.
MFC after: 2 weeks
These device IDs have an AR3012 bluetooth device that shows up with
bcdDevice=1 when it doesn't have the firmware loaded, and bcdDevice=2
when it's ready to speak full HCI.
Tested:
* AR5B225 PCIe - AR9485 + AR3012
exception more readable. In practice they prevented all logging during
a machine check exception on at least some systems. Specifically, when
an uncorrected ECC error is detected in a DIMM on a Nehalem/Westmere
class machine, all CPUs receive a machine check exception, but only
CPUs on the same package as the memory controller for the erroring DIMM
log an error. The CPUs on the other package would complete the scan of
their machine check banks and panic before the first set of CPUs could
log an error. The end result was a clearer display during the panic
(no interleaved messages), but a crashdump without any useful info about
the error that occurred.
To handle this case, make all CPUs spin in the machine check handler
once they have completed their scan of their machine check banks until
at least one machine check error is logged. I tried using a DELAY()
instead so that the CPUs would not potentially hang forever, but that
was not reliable in testing.
While here, don't clear MCIP from MSR_MCG_STATUS before invoking panic.
Only clear it if the machine check handler does not panic and returns
to the interrupted thread.
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
this to the cache line size is required to avoid data corruption on armv4
and armv5, and improves performance on armv6, in both cases by avoiding
partial cacheline flushes for USB IO.
All these configs already exist in 10-stable. A few that don't (and
thus can't be MFC'd yet) will be committed separately.
hardware. It is possible to turn this feature off and fall back to software
emulation of the APIC by setting the tunable hw.vmm.vmx.use_apic_vid to 0.
We now start handling two new types of VM-exits:
APIC-access: This is a fault-like VM-exit and is triggered when the APIC
register access is not accelerated (e.g. apic timer CCR). In response to
this we do emulate the instruction that triggered the APIC-access exit.
APIC-write: This is a trap-like VM-exit which does not require any instruction
emulation but it does require the hypervisor to emulate the access to the
specified register (e.g. icrlo register).
Introduce 'vlapic_ops' which are function pointers to vector the various
vlapic operations into processor-dependent code. The 'Virtual Interrupt
Delivery' feature installs 'ops' for setting the IRR bits in the virtual
APIC page and to return whether any interrupts are pending for this vcpu.
Tested on an "Intel Xeon E5-2620 v2" courtesy of Allan Jude at ScaleEngine.
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
Keep a copy of the 'rip' and the 'exit_reason' and use that when calling
vmx_exit_trace(). This is because both the 'rip' and 'exit_reason' can
be changed by 'vmx_exit_process()' and can lead to very misleading traces.
Remove old bits of data concat for 'ascii' field.
Remove special SIOCGIFSTATUS handling from if.c (which Coverity yells at).
Reported by: Coverity
Coverity CID: 1147174
MFC after: 2 weeks
when PMC-soft feature is not used the check will be false.
Sponsored by: EMC / Isilon storage division
Submitted by: Anton Rang <anton.rang@isilon.com>
The uboot mapping is only 128KiB (0x20000) and not 2MiB (0x200000).
Dynamically adjust kernel and rootfs mappings based on the
geom_uncompress(4) magic.
This makes the built images more reliable by accepting changes on kernel
size transparently and matches the images built with zrouter and
freebsd-wifi-build.
Tested by: gjb
Approved by: adrian (mentor)
Obtained from: Zrouter
WARNING: icl_pdu_check_data_digest: data digest check failed; got 0xf23b,
should be 0xdb7f23b
Tested by: Darcy Birkbeck
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
value. The "Intel Lynx Point" XHCI controller found in the MBP2013 has
been observed to not always set the event interrupt bit while there
are events to consume in the event ring.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
the vcpu should be kicked to process a pending interrupt. This will be useful
in the implementation of the Posted Interrupt APICv feature.
Change the return value of 'vlapic_pending_intr()' to indicate whether or not
an interrupt is available to be delivered to the vcpu depending on the value
of the PPR.
Add KTR tracepoints to debug guest IPI delivery.
the spoofed identify data into the user buffer rather than issuing the
command to the controller, since Chatham IDENTIFY data is always spoofed.
While here, fix a bug in the spoofed data for Chatham submission and
completion queue entry sizes.
Sponsored by: Intel
MFC after: 3 days
'vmx_vminit()' that does customization.
This makes it easier to turn on optional features (e.g. APICv) without
having to keep adding new parameters to 'vmcs_set_defaults()'.
Reviewed by: grehan@
