Ensure that d_delmaxsize is always set, removing init to 0 which could cause
future issues if use cases change.
Allow kern.cam.da.X.delete_max (which maps to d_delmaxsize) to be increased
up to the calculated max after being reduced.
MFC after: 1 day
X-MFC-With: r249940
needed for the last 10 years. Far too much of the internal API is
exposed, and every small adjustment causes applications to stop working.
To kick this off, bump the API version to 0x17 as should have been done
with r246713, but add shims to compensate. Thanks to the shims, there
should be no visible change in application behavior.
I have plans to do a significant overhaul of the API to harnen it for
the future, but until then, I welcome others to add shims for older
versions of the API.
Obtained from: Netflix
SPC-4 specification states that serial number may be property of device,
but not a specific logical unit. People reported about FC storages using
serial number in that way, making it unusable for purposes of LUN multipath
detection. SPC-4 states that designators associated with logical unit from
the VPD page 83h "Device Identification" should be used for that purpose.
Report first of them in the new attribute in such preference order: NAA,
EUI-64, T10 and SCSI name string.
While there, make GEOM DISK properly report GEOM::ident in XML output also
using d_getattr() method, if available. This fixes serial numbers reporting
for SCSI disks in `geom disk list` output and confxml.
Discussed with: gibbs, ken
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
While GEOM in general has provider opened while sending BIO_GETATTR,
GEOM DISK does not really need to open disk to read medium-unrelated
attributes for own use.
Proposed by: ken
Re-ordered SSD quirks alphabetically so they are easier to maintain.
Removed my email and PR reference from comments on each quirk.
Added quirks for more SSDs:
* Crucial M4
* Corsair Force GT
* Intel 520 Series
* Kingston E100 Series
* Samsung 830 Series
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 1 week
This prevents users from selecting a delete method which may cause
corruption e.g. MPS WS16 on pre P14 firmware.
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 2 days
With "cached read" HDD testing and multiple ports busy on a SATA
host controller, 3726/3826 PMP will very rarely drop a deferred
R_OK that was intended for the host. Symptom will be all 5 drives
under test will timeout, get reset, and recover.
Submitted by: Rich Futyma <rich.futyma@sanmina.com>
MFC after: 2 weeks
- remove DA_FLAG_SAW_MEDIA flag, almost opposite to DA_FLAG_PACK_INVALID,
using the last instead.
- allow opening device with no media present, reporting zero media size
and non-zero sector size, as geom/notes suggests. That allow to read
device attributes and potentially do other things, not related to media.
to query ATA functionality via ATA Pass-Through (16) as this page is defined
as "must" for SATL devices, hence indicating that the device is at least
likely to support Pass-Through (16).
This eliminates errors produced by CTL when ATA Pass-Through (16) fails.
Switch ATA probe daerror call to SF_NO_PRINT to avoid errors printing out
for devices which return invalid errors.
Output details about supported and choosen delete method when verbose booted.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 1 week
Ensure that delete_available is reset so re-probes after a media change,
to one with different delete characteristics, will result in the correct
methods being flagged as available.
Make all ccb state changes use a consistent flow:
* free()
* xpt_release_ccb()
* softc->state = <new state>
* xpt_schedule()
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 1 week
Remove ADA_FLAG_PACK_INVALID flag. Since ATA disks have no concept of media
change it only duplicates CAM_PERIPH_INVALID flag, so we can use last one.
Slightly cleanup DA_FLAG_PACK_INVALID use.
Give periph validity flag own periph reference. That slightly simplifies
the release logic and covers hypothetical case if lock is dropped inside
the periph_oninval() method.
requests.
sys/geom/geom_disk.h:
- Added d_delmaxsize which represents the maximum size of individual
device delete requests in bytes. This can be used by devices to
inform geom of their size limitations regarding delete operations
which are generally different from the read / write limits as data
is not usually transferred from the host to physical device.
sys/geom/geom_disk.c:
- Use new d_delmaxsize to calculate the size of chunks passed through to
the underlying strategy during deletes instead of using read / write
optimised values. This defaults to d_maxsize if unset (0).
- Moved d_maxsize default up so it can be used to default d_delmaxsize
sys/cam/ata/ata_da.c:
- Added d_delmaxsize calculations for TRIM and CFA
sys/cam/scsi/scsi_da.c:
- Added re-calculation of d_delmaxsize whenever delete_method is set.
- Added kern.cam.da.X.delete_max sysctl which allows the max size for
delete requests to be limited. This is useful in preventing timeouts
on devices who's delete methods are slow. It should be noted that
this limit is reset then the device delete method is changed and
that it can only be lowered not increased from the device max.
Reviewed by: mav
Approved by: pjd (mentor)
maximum sizes for said methods, which are used when processing BIO_DELETE
requests. This includes updating UNMAP support discovery to be based on
SBC-3 T10/1799-D Revision 31 specification.
Added ATA TRIM support to cam scsi devices via ATA Pass-Through(16)
sys/cam/scsi/scsi_da.c:
- Added ATA Data Set Management TRIM support via ATA Pass-Through(16)
as a delete_method
- Added four new probe states used to identity available methods and their
limits for the processing of BIO_DELETE commands via both UNMAP and the
new ATA TRIM commands.
- Renamed Probe states to better indicate their use
- Added delete method descriptions used when informing user of issues.
- Added automatic calculation of the optimum delete mode based on which
method presents the largest maximum request size as this is most likely
to result in the best performance.
- Added WRITE SAME max block limits
- Updated UNMAP range generation to mirror that used by ATA TRIM, this
optimises the generation of ranges and fixes a potential overflow
issue in the count when combining multiple BIO_DELETE requests
- Added output of warnings about short deletes. This should only ever
be triggered on devices that fail to correctly advertise their supported
delete modes / max sizes.
- Fixed WS16 requests being incorrectly limited to 65535 in length.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
so its available for use in generic scsi code.
This is a pre-requirement for using VPD queries to determine available SCSI
delete methods within scsi_da.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
commands to an ATA device attached via a SCSI control.
sys/cam/scsi/scsi_all.c:
- Added scsi_ata_identify, scsi_ata_trim
Which use ATA Pass-Through to send commands to the attached disk.
sys/cam/scsi/scsi_all.h:
- Added defines for all missing ATA Pass-Through commands values.
- Added scsi_ata_identify, scsi_ata_trim methods used in ATA TRIM
support.
- Added scsi_vpd_logical_block_prov structure used when querying for
the supported sizes UNMAP commands.
- Added scsi_vpd_block_limits structure used when querying for the
supported sizes of the UNMAP command.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
This allows users who boot without loader to adjust their environments
around slightly buggy or slow hardware.
PR: kern/161809
Submitted by: rozhuk.im@gmail.com
MFC after: 2 weeks
This allows mapping a tape drive in a changer (as reported by
'chio status') to a sa(4) driver instance by comparing the
serial numbers.
The designators can be ASCII (which is printed out directly), binary
(which is printed in hex format) or UTF-8, which is printed in either
native UTF-8 format if the terminal can support it, or in %XX notation
for non-ASCII characters. Thanks to Hiroki Sato <hrs@> for the
explaining UTF-8 printing and example UTF-8 printing code.
chio.h: Modify the changer_element_status structure to add new
fields and definitions from the SMC3r16 spec.
Rename the original CHIOGSTATUS ioctl to OCHIOGTATUS and
define a new CHIOGSTATUS ioctl.
Clean up some tab/space issues.
chio.c: For the 'status' subcommand, print the designator field
if it is supplied by a device.
scsi_ch.h: Add new flags for DVCID and CURDATA to the READ
ELEMENT STATUS command structure.
Add a read_element_status_device_id structure
for the data fields in the new standard. Add new
unions, dt_or_obsolete and voltage_devid, to hold
and address data from either SCSI-2 or newer devices.
scsi_ch.c: Implement support for fetching device IDs with READ
ELEMENT STATUS data.
Add new arguments to scsi_read_element_status() to
allow the user to request the DVCID and CURDATA bits.
This isn't compiled into libcam (it's only an internal
kernel interface), so we don't need any special
handling for the API change.
If the user issues the new CHIOGSTATUS ioctl, copy all of
the available element status data out. If he issues the
OCHIOGSTATUS ioctl, we don't copy the new fields in the
structure.
Fix a bug in chopen() that would result in the peripheral
never getting unheld if chgetparams() failed.
Sponsored by: Spectra Logic
Submitted by: Po-Li Soong
MFC After: 1 week
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning. NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph". If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
r248917, r248918, r248978, r249001, r249014, r249030:
Remove multilevel freezing mechanism, implemented to handle specifics of
the ATA/SATA error recovery, when post-reset recovery commands should be
allocated when queues are already full of payload requests. Instead of
removing frozen CCBs with specified range of priorities from the queue
to provide free openings, use simple hack, allowing explicit CCBs over-
allocation for requests with priority higher (numerically lower) then
CAM_PRIORITY_OOB threshold.
Simplify CCB allocation logic by removing SIM-level allocation queue.
After that SIM-level queue manages only CCBs execution, while allocation
logic is localized within each single device.
Suggested by: gibbs
