before VM has been initialized. This includes:
1. Replacing pmap_steal_memory(),
2. Replace the handcrafted logic to allocate a naturally aligned VHPT,
3. Properly allocate the DPCPU for the BSP.
Ad 3: Appending the DPCPU to kernend worked as long as we wouldn't
cross into the next PBVM page. If we were to cross into the next
page, then there wouldn't be a PTE entry on the page table for it
and we would end up with a MCA following a page fault. As such,
this commit fixes MCAs occasionally seen.
arm platform. Add all the atmel boards to the ATMEL kernel for
testing purposes. Until boot loader arg parsing of baord type
is done, this won't actually be able to do the runtime selection.
100 bytes from the binary with silly tricks. Hope to get this small
enough to run on the models that have 4k SRAM. We are close compiled
for the at91rm9200, but still need to trim for the target.
correctly. We now iterate the EFI memory descriptors once and collect all
the information in a single pass. This includes:
1. The I/O port base address,
2. The PAL memory region. Have the physmem API track this.
3. Memory descriptors of memory we can't use, like bad memory, runtime
services code & data, etc. Have the physmem API track these.
4. memory descriptors of memory we can use or re-use, such as free
memory, boot time services code & data, loader code & data, etc.
These are added by the physmem API.
Since the PBVM page table and pages are in memory described as loader
data, inform the physmem API of chunks that need to be delated from the
available physical memory.
While here, remove Maxmem and replace it with the better named paddr_max.
Maxmem was defined as physmem, which is generally wrong. Now, paddr_max
is properly defined as the largesty physical address.
The upshot of all this is that:
1. We properly determine realmem.
2. We maximize physmem by re-using memory where possible.
3. We remove complexity from ia64_init() in machdep.c.
4. Remove confusion about realmem, physmem & Maxmem.
The new ia64_physmem_alloc() is to replace pmap_steal_memory() in pmap.c,
as well as replace the handcrafted allocation of the VHPT for the BSP in
pmap_bootstrap() in pmap.c. This is step 2 and addresses the manipulation
of phys_avail after it is being created.
Don't use Maxmem when the amount of memory is meant. Use realmem instead.
Maxmem is not only a MD variable, it represents the highest physical memory
address in use. On systems where memory is sparsely layed-out the highest
memory address and the amount of memory are not interchangeable. Scaling the
AGP aperture based on the actual amount of memory (= realmem) rather than
the available memory (= physmem) makes sure there's consistent behaviour
across architectures.
agp_i810.c:
While arguably the use of Maxmem can be considered correct, replace its use
with realmem anyway. agp_i810.c is specific to amd64, i386 & pc98, which
have a dense physical memory layout. Avoiding Maxmem here is done with an
eye on copy-n-paste behaviour in general and to avoid confusion caused by
using realmem in agp.c and Maxmem in agp_i810.c.
In both cases, remove the inclusion of md_var.h
Update DTrace disassembler accordingly. The code to treat the prefixes
as null prefixes was already in place.
Although in practice compilers seem to generate only cs-prefix for use
in long NOPs, the same treatment is applied to all of cs, ds, es, ss for
consistency.
Reported by: emaste
Tested by: emaste
Obtained from: Illumos commit 13442:4adbe6de60c8 (+ local changes)
MFC after: 5 days
- Add generic support for opcodes that are escape bytes used for
multi-byte opcodes (such as the 0x0f prefix). Use this to replace
the hard-coded 0x0f special case and add support for three-byte
opcodes that use the 0x0f38 prefix.
- Decode all Intel VMX instructions. invept and invvpid in particular are
three-byte opcodes that use the 0x0f38 escape prefix.
- Rework how the special 'SDEP' size flag works such that the default
instruction name (i_name) is the instruction when the data size
prefix (0x66) is not specified, and the alternate name in i_extra is
used when the prefix is included.
- Add a new 'ADEP' size flag similar to 'SDEP' except that it chooses
between i_name and i_extra based on the address size prefix (0x67).
Use this to fix the decoding for jrcxz vs jecxz which is determined
by the address size prefix, not the operand size prefix. Also, jcxz
is not possible in 64-bit mode, but jrcxz is the default instruction
for that opcode.
- Add support for handling instructions that have a mandatory 'rep'
prefix (this means not outputting the 'repe ' prefix until determining
if it is used as part of an opcode). Make 'pause' less of a special
case this way.
- Decode 'cmpxchg16b' and 'cdqe' which are variants of other instructions
but with a REX.W prefix.
MFC after: 1 month
"Reserved by Microsoft" in the standard PNP ID table, but has been seen
in the wild on at least one laptop.
PR: kern/169571
Submitted by: Matthias Apitz guru unixarea de
MFC after: 3 days
functions that manage PV entries. Specifically, remove the PV entry from
the containing PV list only after the corresponding PTE is destroyed.
Update the pmap's wired mapping count in pmap_enter() before the PV list
lock is acquired.
- Add a couple of new devices
- Flow control changes in shared and core code
- Bug fix to Flow Director for 82598
- Shared code sync to internal with required core change
Thanks to those helping in the testing and improvements to this driver!
MFC after:5 days
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
natively rather than hand-assembled versions. For xgetbv/xsetbv, add a
wrapper API to deal with xcr* registers: rxcr() and load_xcr().
Reviewed by: kib
MFC after: 1 month
This will allow HAST to read directly from the local component without
even communicating userland daemon.
Sponsored by: Panzura, http://www.panzura.com
MFC after: 1 month
Before this change the IV-Key was used to generate encryption keys,
which was incorrect, but safe - for the XTS mode this key was unused
anyway and for CBC mode it was used differently to generate IV
vectors, so there is no risk that IV vector collides with encryption
key somehow.
Bump version number and keep compatibility for older versions.
MFC after: 2 weeks
it skips FLOWTABLE lookup. However, the non-NULL ro has dual meaning
here: it may be supplied to provide route, and it may be supplied to
store and return to caller the route that ip_output()/ip6_output()
finds. In the latter case skipping FLOWTABLE lookup is pessimisation.
The difference between struct route filled by FLOWTABLE and filled
by rtalloc() family is that the former doesn't hold a reference on
its rtentry. Reference is hold by flow entry, and it is about to
be released in future. Thus, route filled by FLOWTABLE shouldn't
be passed to RTFREE() macro.
- Introduce new flag for struct route/route_in6, that marks route
not holding a reference on rtentry.
- Introduce new macro RO_RTFREE() that cleans up a struct route
depending on its kind.
- All callers to ip_output()/ip6_output() that do supply non-NULL
but empty route should use RO_RTFREE() to free results of
lookup.
- ip_output()/ip6_output() now do FLOWTABLE lookup always when
ro->ro_rt == NULL.
Tested by: tuexen (SCTP part)
The new driver changed the size of the mfi_dcmd_frame structure in such a
way that a MFI_IOC_PASSTHRU ioctl from an old amd64 binary is treated as an
MFI_IOC_PASSTHRU32 ioctl in the new driver. As a result, the user pointer
is treated as the buffer length. mfi_user_command() doesn't have a bounds
check on the buffer length, so it passes a really big value to malloc()
which panics when it tries to exhaust the kmem_map. Fix this two ways:
- Only honor MFI_IOC_PASSTHRU32 if the binary has the SV_ILP32 flag set,
otherwise treat it as an unknown ioctl.
- Add a bounds check on the buffer length passed by the user. For now
it fails any user attempts to use a buffer larger than 1MB.
While here, fix a few other nits:
- Remove an unnecessary check for a NULL return from malloc(M_WAITOK).
- Use the ENOTTY errno for invalid ioctl commands instead of ENOENT.
MFC after: 3 days
- Add a note to the ipfw(8) man page about the rules no longer being
case sensitive.
- Fix some typos in the man page.
PR: docs/164772
Reviewed by: bz
Approved by: gabor (doc mentor, src committer)
MFC after: 2 weeks
The RX EDMA support requires a modified approach to the RX descriptor
handling.
Specifically:
* There's now two RX queues - high and low priority;
* The RX queues are implemented as FIFOs; they're now an array of pointers
to buffers;
* .. and the RX buffer and descriptor are in the same "buffer", rather than
being separate.
So to that end, this commit abstracts out most of the RX related functions
from the bulk of the driver. Notably, the RX DMA/buffer allocation isn't
updated, primarily because I haven't yet fleshed out what it should look
like.
Whilst I'm here, create a set of matching but mostly unimplemented EDMA
stubs.
Tested:
* AR9280, station mode
TODO:
* Thorough AP and other mode testing for non-EDMA chips;
* Figure out how to allocate RX buffers suitable for RX EDMA, including
correctly setting the mbuf length to compensate for the RX descriptor
and completion status area.
This driver does not yet handle multiple chip selects properly.
Note that the NAND infrastructure does not perform full page
reads or writes, which means that this driver cannot make use
of the hardware ECC that is otherwise present.
