floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
a vga.
* Fix broken logic in syscons for a failed probe.
* Fix AlphaStation 500/600 so that non-serial consoles are supported.
Submitted by: Thomas Valentino Crimi <tcrimi+@andrew.cmu.edu> (vga bits),
Andrew Gallatin <gallatin@cs.duke.edu> (AS500/AS600)
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
went backwards when interrupts were masked for more than one i8254
interrupt period. It sometimes went backwards when the i8254 counter
was reprogrammed. Neither of these should happen in normal operation.
Update the i8254 timecounter support variables atomically. Calling
timecounter functions from fast interrupt handlers may actually work
in all cases now.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
hopefully become a portable driver usable by all architectures. The api
support files have had to be copied to sys/alpha/include since userland
programs expect to find them in <machine/*.h>.
All the revision history of the i386 syscons has been retained by a
repository copy.
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
When bell is of "quiet" types, the console won't ring (or flush)
if the ringing process is in a background vty.
PR: i386/2853
- Modify the escape sequence 'ESC[=%d;%dB' so that bell pitch and
duration are set in hertz and msecs by kbdcontrol(1).
There will be a corresponding kbdcontrol patch.
PR: bin/6037
Submitted by: Kouichi Hirabayashi (kh@eve.mogami-wire.co.jp)
- Call isa_dmadone() whenever necessary to stop DMA and/or free bounce
buffers. Undead DMA corrupted the malloc freelist fairly consistently
in the following configuration: SLICE kernel, 2 floppy drives, no disk
in fd0, disk in fd1.
- Don't call fdc_reset() from fd_timeout(). Doing so gave an "extra"
interrupt which was usually misinterpreted as being for completion
of the next FDC command; the interrupt for completion of the next
FDC command was then usually misinterpreted... There were further
complications for interrupts latched by the soft-spl mechanism so
that they were delivered after all the h/w interrupts went away.
This caused at least wrong head settle delays and may be why the
FreeBSD floppy driver seems to munch floppies more than most floppy
drivers. The reset was unnecessary anyway in cases that didn't have
the bug described next, since is was repeated a little later for
the IOTIMEDOUT state. The state machine has complications to handle
resets correctly, so just use it.
- Don't call retrier() from fd_timeout(). The IOTIMEDOUT state needs
to be processed next, and it isn't valid to set to that state if
retrier() has aborted the current transfer. Doing so caused null
pointer panics after the previous bug was fixed.
Improved error handling:
- If an i/o is aborted, arrange to reset in the state machine before
doing the next i/o. New fdc flag for this. This fixes spurious
warnings and lengthy busy-waiting for the next i/o.
- Split STARTRECAL into RESETCOMPLETE and STARTRECAL and only check
for the results from reset if we actually reset. This fixes spurious
warnings for other paths to STARTRECAL. [Oops, it may break reset
handling for motor-off resets.]
Cleanups in fd_timeout():
- Renamed to fd_iotimeout() to make it clearer that it is only used
for i/o.
- Don't handle the bp == 0 case. This case can't happen for i/o.
- Don't check for controller-busy. We know it must be.
- Don't print anything. retrier() already prints too much for normal
errors.
- Fudge the state differently so that the state machine advances
fdc->retry and the status is invalid (perhaps this should fudge a
valid state like the one for WP).
- Style fixes.
controller reports a successful seek, it is very unlikely to report
seeking to a cylinder other than the one requested, but we check for
this, and botched the error handling for the requested_cylinder != 0
case. This error happened when the bug fixed in rev.1.52 of <sys/buf.h>
caused the head of buffer queue to change to one starting on a different
cylnder - the requested cylinder was found, but it wasn't what we
thought we requested. The fix is simply to arrange to reset the state
machine.
Corruption of the buffer queue seems to only have been a problem in the
floppy driver. Other drivers dequeue the head of the queue before doing
physical i/o on it, so the corruption at worse broke the elevator sort
order. Dequeueing breaks it anyway.
