The FXP_SCR_FLOWCONTROL registers is at offset 0x19, but 2 bytes wide.
It cannot be read as a word without causing a panic on architectures
that enforce strict alignment.
MFC after: 3 days
that if softclock is running on another CPU and is blocked on our driver
lock, we will wait until it has acquired the lock, seen that it was
cancelled, dropped the lock, and awakened us so that we can safely destroy
the mutex.
MFC after: 3 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
the timeout routine.
- Fix locking in detach.
- Add locking in shutdown.
- Don't mess with the PCI command register in resume, the PCI bus driver
already does this for us.
- Add locking to the non-serial ifmedia routines.
- Fix locking in ioctl.
- Remove spls and support for 4.x.
MFC after: 1 week
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
latest 82550 and 82551 chipsets (revision IDs 0x0e, 0x0f and 0x10).
We were only enabling it for revisions 0x0c and 0x0d, now it's
enabled for any 8255x NIC with a revision ID bigger than 0x0c. It
should be safe, and this is what Intel does in their open source
driver.
MFC after: 2 weeks
Tested by: Pavel Lobach lobach_pavel at mail dot ru
from an mbuf into the fxp_encap() function, as done in other drivers.
- Don't waste time calling bus_dmamap_load_mbuf() if we know the mbuf
chain is too long to fit in a TX descriptor, call m_defrag() first.
- Convert fxp(4) to use bus_dmamap_load_mbuf_sg().
a vlan interface attached to a fxp(4) card when it has not been
initialized yet. We now set the links from our internel TX descriptor
structure to the TX command blocks at attach time rather than at init
time. While I'm here, slightly improve the style in fxp_attach().
PR: kern/78112
Reported by: Gavin Atkinson <gavin.atkinson@ury.york.ac.uk> and others
Tested by: flz, Gavin Atkinson <gavin.atkinson@ury.york.ac.uk>
MFC after: 1 week
testing it to know whether we should enable the 82503 serial mode...
Move code to the right location and disallow the use of the 82503
serial mode if the sc->revision field is 0 again. This makes fxp(4)
work correctly with ATMEL 350 93C46 cards (3 port 82559 based with a
82555 PHY), as well as with the older ATMEL 220 93C46 (same flavour)
and with the even older 10Mbps-only 82557 cards with the 82503 serial
interface.
Tested by: Andre Albsmeier <andrer@albsmeier.net>, krion
MFC after: 2 weeks
interface as well. This is not an expected revision id per the
datasheet, but unfortunately there are such cards out there with
a 82557 chipset, and they want to use the 82503.
PR: kern/75739
Reported by: Andre Albsmeier <andre.albsmeier@siemens.com>
datasheet says it is only valid for such chipsets and shouldn't be used
with others. This fixes some 82559 based cards which otherwise only
work at 10Mbit.
MFC after: 5 days
Tested by: krion
following drivers: bfe(4), em(4), fxp(4), lnc(4), tun(4), de(4) rl(4),
sis(4) and xl(4)
More patches are pending on: http://peoples.freebsd.org/~mlaier/ Please take
a look and tell me if "your" driver is missing, so I can fix this.
Tested-by: many
No-objection: -current, -net
sysctls were global (hw.fxp_rnr and hw.fxp_noflow), all of them are
now per-device. Sample output of "sysctl dev.fxp0" with this patch,
with the standard %foo nodes removed :
dev.fxp0.int_delay: 1000
dev.fxp0.bundle_max: 6
dev.fxp0.rnr: 0
dev.fxp0.noflow: 0
In particular, disabling it was likely to break configurations
involving ng_vlan(4) since the latter couldn't control
the parent's VLAN_MTU in the way vlan(4) did.
Pointed out by: ru
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
