initializing structures, like the pv table, that are only used to
implement superpages. In fact, some of the unnecessary code in
pmap_init() was actually doing harm. It was preventing the kernel from
booting on virtual machines with more than 768 MB of memory.
Tested by: sbruno
- Fix boot0 to check for PXE when using the pre-set setting for the
preferred slice.
- Update boot0cfg to use slice 6 to select PXE. Accept a 'pxe' argument
instead of a number for the 's' option as a way to select PXE as well.
Submitted by: Andrew Boyer aboyer averesystems
MFC after: 2 weeks
7.x, 8.x and 9.x with pf(4) imports: pfsync(4) should suppress CARP
preemption, while it is running its bulk update.
However, reimplement the feature in more elegant manner, that is
partially inspired by newer OpenBSD:
- Rename term "suppression" to "demotion", to match with OpenBSD.
- Keep a global demotion factor, that can be raised by several
conditions, for now these are:
- interface goes down
- carp(4) has problems with ip_output() or ip6_output()
- pfsync performs bulk update
- Unlike in OpenBSD the demotion factor isn't a counter, but
is actual value added to advskew. The adjustment values for
particular error conditions are also configurable, and their
defaults are maximum advskew value, so a single failure bumps
demotion to maximum. This is for POLA compatibility, and should
satisfy most users.
- Demotion factor is a writable sysctl, so user can do
foot shooting, if he desires to.
* Right now the delay is hard coded at 10uS. This is a bit long when doing lots
of periodic i2c transactions. So create a 'udelay' parameter and initialise it
to 10. This can be tuned later.
* Add a newline after a transaction finishes, so the debugging output isn't so
horrible.
performance issues.
* Access to the GPIO bus is already locked by requesting
and releasing the bus - thus the lock isn't really needed
for each GPIO pin change.
* Don't lock and unlock the GPIO bus for -each- i2c access -
the i2c bus code is already doing this by calling the upper
layer callback to request/release the bus. This thus locks
the bus for the entirety of the transaction.
TODO:
* Further verify that everything is correctly requesting/
releasing the GPIO bus.
* Look at how to lock the GPIO pin configuration stuff,
potentially by locking/unlocking the bus at the gpiobus
layer.
With the previous code, if the range of priorities for timeshare batch
threads was greater than RQ_NQS, then the threads with low priorities in
the part of the range above RQ_NQS would be scheduled to the run-queues
as if they had high priorities at the beginning of the range.
In other words, threads with a nice level of +N could be scheduled as
if they had a nice level of -M.
Reported by: George Mitchell <george@m5p.com>
Reviewed by: jhb
Tested by: George Mitchell <george@m5p.com> (earlier version)
MFC after: 1 week
Fix the TCP header size calculation such that makes TSO engine
cache all header(ethernet/IP/TCP) bytes to its internal buffer.
While here, remove extra pull up for TCP payload. Unlike some
em(4) controllers, fxp(4) does not require such work around for
TSO.
The two limitations are ethernet/IP/TCP header size should be less
than or equal to the size of controller's internal buffer(80 bytes)
and these header information should be found in the first fragment
of a TSO frame.
of the rx_ring to bus_dmamap_sync(9). Given that netmap code tries to
obtain the bus addresses of netmap buffers via vtophys(9) instead of using
bus_dma(9) it currently has zero chance of actually working on sparc64
though (and for that matter f.e. also not with MACs limited to 32-bit DMA
on x86 machines with more than 4GB of RAM).
(ss == NULL) on pool import. I had such a panic recently. With current version
of ZFS it is still possible to import the pool in readonly mode and backup
all the data, but in case it is impossible for some reason add tunable
vfs.zfs.space_map_last_hope, which when set to '1' will tell ZFS to remove
colliding range and retry. This seems to have worked for me, but I consider
it highly risky to use.
MFC after: 1 week
locate a process calling pfind() and do some additional checks like
p_candebug(). To reduce this code duplication a new function pget() is
introduced and used.
As the function may be useful not only in kern_proc.c it is in the
kernel name space.
Suggested by: kib
Reviewed by: kib
MFC after: 2 weeks
- put underlying keyboard(s) into the polling mode for the whole
duration of the grab, instead of the previous behavior of going into
and out of the polling mode around each polling attempt
- ditto for setting K_XLATE mode and enabling a disabled keyboard
Inspired by: bde
MFC after: 2 months
This is intended as a replacement for libkern's gets and mostly borrows
its implementation. It uses cngrab/cnungrab to delimit kernel's access
to console input.
Note: libkern's gets obviously doesn't share any bits of implementation
iwth libc's gets. They also have different APIs and the former doesn't
have the overflow problems of the latter.
Inspired by: bde
MFC after: 2 months
At the moment grab and ungrab methods of all console drivers are no-ops.
Current intended meaning of the calls is that the kernel takes control of
console input. In the future the semantics may be extended to mean that
the calling thread takes full ownership of the console (e.g. console
output from other threads could be suspended).
Inspired by: bde
MFC after: 2 months
case where a kevent would not fire on a regular file if an application read
to EOF and then seeked backwards into the file.
Reviewed by: kib
MFC after: 2 weeks
Fix a comment from the previous commit.
Use M_ZERO instead of bzero() in ext2_vfsops.c
Add include guards from PR.
PR: 162564
Approved by: jhb (mentor)
MFC after: 2 weeks
unsupported form of the latter. This change has been reviewed and accepted
in the -hackers list.
Submitted by: Alexander Best
Reviewed by: David Schulz
from scratch, copying needed functionality from the old implemenation
on demand, with a thorough review of all code. The main change is that
interface layer has been removed from the CARP. Now redundant addresses
are configured exactly on the interfaces, they run on.
The CARP configuration itself is, as before, configured and read via
SIOCSVH/SIOCGVH ioctls. A new prefix created with SIOCAIFADDR or
SIOCAIFADDR_IN6 may now be configured to a particular virtual host id,
which makes the prefix redundant.
ifconfig(8) semantics has been changed too: now one doesn't need
to clone carpXX interface, he/she should directly configure a vhid
on a Ethernet interface.
To supply vhid data from the kernel to an application the getifaddrs(8)
function had been changed to pass ifam_data with each address. [1]
The new implementation definitely closes all PRs related to carp(4)
being an interface, and may close several others. It also allows
to run a single redundant IP per interface.
Big thanks to Bjoern Zeeb for his help with inet6 part of patch, for
idea on using ifam_data and for several rounds of reviewing!
PR: kern/117000, kern/126945, kern/126714, kern/120130, kern/117448
Reviewed by: bz
Submitted by: bz [1]
- Add __alignof() for non-GCC and GCC < 2.95.
- Simply implement the C1X keywords on top of the existing __macros.
- Add struct __hack to _Static_assert to require consumers to add a
semicolon.
- Add an extra underscore to __assert_ to allow it to be combined with
locally defined versions of CTASSERT in the tree.
- Add proper casts to __offsetof() to make it work for cases where
sizeof(size_t) != sizeof(uintptr_t).
- Globally replace size_t and uintptr_t by __size_t and __uintptr_t.
This removes the dependency on <sys/types.h> / <stdint.h>. Practically
any header file ends up including <machines/_types.h> somehow.
- Change argument names of macros to match with the rest of the file.
MFC after: 3 months
- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
The feature has been standard for a while in UFS as a means to reduce
fragmentation, therefore maintaining consistent performance with
filesystem aging. This is also very similar to what ext4 calls
"delayed allocation".
In his 2010 GSoC, Zheng Liu ported and benchmarked the missing
FANCY_REALLOC code to find more consistent performance improvements than
with the preallocation approach.
PR: 159233
Author: Zheng Liu <gnehzuil AT SPAMFREE gmail DOT com>
Sponsored by: Google Inc.
Approved by: jhb (mentor)
MFC after: 2 weeks
Since mpboot.s enables processor support for PG_PS before enabling
paging, there is no reason that the identity must use 4 KB page mappings.
Discussed with: jhb
- Write Buffers have to be drained after write to Page Table even if caches
are in write-through mode.
- Make sure to sync PTE in pmap_zero_page_generic().
Submitted by: Michal Mazur
Reviewed by: cognet
Obtained from: Semihalf
MFC after: 1 month
the full length from offset is being flushed. Note that for now VOP_FSYNC
does not support offset and length parameters so we still do the same full
VOP_FSYNC. This issue was reported at FreeNAS support site as FreeNAS
ticket #1096.
Submitted by: "ceckerle" <ce.freenas eckerle net>
Prodded by: gcooper
Reviewed by: rmacklem
MFC after: 2 weeks
* Add in a default GPIO section for AR91XX_BASE.hints, which doesn't
define the GPIO function masks or any GPIO pines.
* Add in the GPIO line definitions for LEDs and GPIO pins for the
TP-WR1043nd.
I've verified the LEDs work fine using gpioset.
config and function mask setup.
* "gpiomask" now specifies which GPIO pins to enable, for devices to bind to.
* "function_set" allows bits in the function register to be set at GPIO setup.
* "function_clear" allows bits in the function register to be cleared at
GPIO setup.
The function_set/function_clear bits allow for individual GPIO pins to either
drive a GPIO line or an alternate function - eg USB, JTAG, etc. This allows
for things like CS1/CS2 be enabled for those boards w/ >1 SPI device connected,
or disabling JTAG for the AR7240 (which is apparently needed ..)
I've verified this on the AR71xx.
attached this way.
The AR5212 based NICs have a variety of RF frontends, so there's a linker set
which the AR5212 attach routine calls. The same framework is used for the
AR5416 and later but as there's a fixed RF frontend for each 11n NIC, it
is just directly attached.
However in the case of compiling a cut down HAL (eg _just_ AR9130 WMAC support),
the linker set ends up being empty and this causes the compile to fail.
So this is just a workaround for that - it means those users who wish an 11n
only HAL can compile the 11n chipsets and RF frontend they need, and just
"ath_ar5212" for the AR5212/AR5416 common code, and it'll just work.
Sponsored by: Hobnob, Inc.
* Call it before sending probe responses, so the ACL code has the
chance to reject sending them.
* Pass the whole frame to the ACL code now, rather than just the
destination MAC - that way the ACL module can look at the frame
contents to determine what the response should be.
This is part of some uncommitted work to support band steering.
Sponsored by: Hobnob, Inc.
The reverse direction of a pipe is lazily allocated on the first write in
that direction (because pipes are usually used in one direction only). A
special case is needed to ensure the pipe appears writable before the first
write because there are 0 bytes of pending data in 0 bytes of buffer space
at that point, leaving 0 bytes of data that can be written with the normal
code.
Note that the first write returns [ENOMEM] if kern.ipc.maxpipekva is
exceeded and does not block or return [EAGAIN], so selecting true for write
is correct even in that case.
PR: kern/93685
Submitted by: gianni
MFC after: 2 weeks
objects created by shm_open(2) into the kernel's address space. This
provides a convenient way for creating shared memory buffers between
userland and the kernel without requiring custom character devices.
This removes the obfuscations mentioned in ext2_readwrite and
places the clustering funtion in a location similar to other
UFS-based implementations.
No performance or functional changeses are expected from
this move.
PR: kern/159232
Suggested by: bde
Approved by: jhb (mentor)
MFC after: 2 weeks
sintrnames and sintrcnt are initialized with non-zero values, which were
discarded by the .bss directive, so consumers like "vmstat -i" were not
getting correct data.
Submitted by: Lukasz Plachno
Obtained from: Semihalf
MFC after: 1 month
- Add _Alignas(). Unfortunately this macro is only partially functional.
The C1X standard will allow both an integer and a type name to be
passed to this macro, while this macro only allows an integer. To be
portable, one must use _Alignas(_Alignof(double)) to use type names.
- Don't do _Static_assert() when __COUNTER__ is not supported. We'd
better keep this implementation robust and allow it to be used in
header files, without mysteriously breaking older compilers.
will time out and close opened /dev/dspX.Y device(s), if
any. This is a workaround because we cannot unregister PCM
devices while the audio character device is in use.
Add a missing inclusion guard.
MFC after: 1 weeks
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
- _Alignof(), which returns the aligment of a certain type.
- _Static_assert(), which can be used to check compile-time assertions.
- _Thread_local, which uses TLS on a variable.
MFC after: 3 months
Reviewed by: mdf
messages.
o Add check for actually resolved speed in miibus_statchg callback
instead of blindly reprogramming BCE_EMAC_MODE register. The
callback may be called multiple times(e.g. link UP, link
transition, auto-negotiate complete etc) while auto-negotiation
is in progress. All unresolved link state changes are ignored
now and setting BCE_EMAC_MODE after link establishment is done
once.
o bce(4) is careful enough not to drive MII_TICK if driver got a
valid link. To detect lost link, bce(4) relied on link state
change interrupt and if driver see the interrupt, it forced to
drive MII_TICK by calling bce_tick() in interrupt handler.
Because bce(4) generates multiple link state change interrupts
while auto-negotiation is in progress, bce_tick() would be
called multiple times and this resulted in generating multiple
link UP/DOWN messages.
With this change, bce_tick() is not called in interrupt handler
anymore such that miibus_statchg callback handles link state
changes with consistent manner.
Reviewed by: davidch
If I interpret the C standard correctly, the storage specifier should be
placed before the inline keyword. While at it, replace __inline by
inline in the files affected.
As C1X is close to being released, there is no need to wrap around a
feature that is already part of C90. Most of these files already use
`const' in different placed as well.
- in destroy_lun_state() assert hold == 1 instead of 0, as it should
receive hold taken by the create_lun_state() or get_lun_statep() before;
- fix hold count leak inside rls_lun_statep() that also fired above assert;
- in destroy_lun_state() use SIM bus number instead of SIM path id for
ISP_GET_PC_ADDR(), as it was before r196008;
- make isp_disable_lun() to set status in CCB;
- make isp_target_mark_aborted() set status into the proper CCB.
Reviewed by: mjacob
Sponsored by: iXsystems, inc.
MFC after: 1 month
usage, but end up with more changes.
- Use SIOCAIFADDR instead of old rusty SIOCSIFADDR, SIOCSIFBRDADDR
and SIOCSIFNETMASK.
- Use queue(9) instead of hand made stailq.
- Use one socket for all ifioctl() and send/receive operations.
- Use __func__ instead of cut-n-paste in logging and panics.
- Axe some dead or strange code.
Tested by: gonzo, Stefan Bethke <stb lassitu.de>
lock_success/lock_failure, introduced in r228424, by directly skipping
in dtrace_probe.
This mainly helps in avoiding namespace pollution and thus lockstat.h
dependency by systm.h.
As an added bonus, this also helps in MFC case.
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
typedef bool. Due to macro expansion it seemed better to use a
typedef for kernel consumers (specifically ofed won't compile
without more changes if a define is used).
- <stdbool.h> should also not re-define bool/true/false if they are
defined by <sys/types.h>. It would probably be a programming error
to define _KERNEL for user-space code, but downstream consumers
like Isilon have already been including <stdbool.h> in kernel
sources, and this protects that usage.
- sizeof(_Bool) is not necessarily the same as sizeof(int), so kernel
modules should be rebuild with this change. Bump __FreeBSD_version.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
- Two struct members eee_disable are used in a function that expects
an int *, so declare them int, not bool.
- igb_tx_ctx_setup() returns a boolean value, so declare it bool, not int.
- igb_header_split is passed to TUNABLE_INT, so delcare it int, not bool.
- igb_tso_setup() returns a bool, so declare it bool, not boolean_t.
- Do not re-define bool/true/false if the symbols already exist.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
- {ixgbe,ixv}_header_split is passed to TUNABLE_INT, so delcare it
int, not bool.
- {ixgbe,ixv}_tx_ctx_setup() returns a boolean value, so declare it
bool, not int.
- {ixgbe,ixv}_tso_setup() returns a bool, so declare it bool, not boolean_t.
- {ixgbe,ixv}_txeof() returns a bool, so declare it bool, not boolean_t.
- Do not re-define bool if the symbol already exists.
MFC after: 2 weeks
Sponsored by: Isilon Systems, LLC
processors with CPUID signature 06_1AH, 06_1EH, and 06_1FH.
Refuse to allocate them on unsupported model.
Submitted by: Davide Italiano <davide.italiano@gmail.com>
MFC after: 1 month
Historical behavior of letting other CPUs merily go on is a default for
time being. The new behavior can be switched on via
kern.stop_scheduler_on_panic tunable and sysctl.
Stopping of the CPUs has (at least) the following benefits:
- more of the system state at panic time is preserved intact
- threads and interrupts do not interfere with dumping of the system
state
Only one thread runs uninterrupted after panic if stop_scheduler_on_panic
is set. That thread might call code that is also used in normal context
and that code might use locks to prevent concurrent execution of certain
parts. Those locks might be held by the stopped threads and would never
be released. To work around this issue, it was decided that instead of
explicit checks for panic context, we would rather put those checks
inside the locking primitives.
This change has substantial portions written and re-written by attilio
and kib at various times. Other changes are heavily based on the ideas
and patches submitted by jhb and mdf. bde has provided many insights
into the details and history of the current code.
The new behavior may cause problems for systems that use a USB keyboard
for interfacing with system console. This is because of some unusual
locking patterns in the ukbd code which have to be used because on one
hand ukbd is below syscons, but on the other hand it has to interface
with other usb code that uses regular mutexes/Giant for its concurrency
protection. Dumping to USB-connected disks may also be affected.
PR: amd64/139614 (at least)
In cooperation with: attilio, jhb, kib, mdf
Discussed with: arch@, bde
Tested by: Eugene Grosbein <eugen@grosbein.net>,
gnn,
Steven Hartland <killing@multiplay.co.uk>,
glebius,
Andrew Boyer <aboyer@averesystems.com>
(various versions of the patch)
MFC after: 3 months (or never)
AIM systems to 4 GB on 32-bit systems and 2^64 bytes on 64-bit systems.
VM_MAXUSER_ADDRESS remains at 2 GB on pending Book-E, pending review of
an increase to 3 GB by those more familiar with Book-E.
pmap_remove() for large sparse requests. This can prevent pmap_remove()
operations on 64-bit process destruction or swapout that would take
several hundred times the lifetime of the universe to complete. This
behavior is largely indistinguishable from a hang.
VM_KMEM_SIZE_MAX. Specifically, if the user/kernel address space split
was changed such that the kernel address space was greater than or equal
to 2 GB, then overflow would occur.
PR: 161721
MFC after: 3 weeks
There have still been intermittent problems with apparent TX
hangs for some customers. These have been problematic to reproduce
but I believe these changes will address them. Testing on a number
of fronts have been positive.
EM: there is an important 'chicken bit' fix for 82574 in the shared
code this is supported in the core here.
- The TX path has been tightened up to improve performance. In
particular UDP with jumbo frames was having problems, and the
changes here have improved that.
- OACTIVE has been used more carefully on the theory that some
hangs may be due to a problem in this interaction
- Problems with the RX init code, the "lazy" allocation and
ring initialization has been found to cause problems in some
newer client systems, and as it really is not that big a win
(its not in a hot path) it seems best to remove it.
- HWTSO was broken when VLAN HWTAGGING or HWFILTER is used, I
found this was due to an error in setting up the descriptors
in em_xmit.
IGB:
- TX is also improved here. With multiqueue I realized its very
important to handle OACTIVE only under the CORE lock so there
are no races between the queues.
- Flow Control handling was broken in a couple ways, I have changed
and I hope improved that in this delta.
- UDP also had a problem in the TX path here, it was change to
improve that.
- On some hardware, with the driver static, a weird stray interrupt
seems to sometimes fire and cause a panic in the RX mbuf refresh
code. This is addressed by setting interrupts late in the init
path, and also to set all interrupts bits off at the start of that.
support of new deltas for both em and igb drivers.
Note that I am not able to track all the bugs fixed in
this code, I am a consumer of it as a component of my
core drivers. It is important to keep the FreeBSD drivers
up to date with it however.
One important note is there is a key fix for 82574 in this
update. Also, there are lots of white space changes, I am
not happy about them but have no control over it :)
control. Controller does not automatically generate pause frames
based on number of available RX buffers so it's very hard to
know when driver should generate XON frame in time. The only
mechanism driver can detect low number of RX buffer condition is
ET_INTR_RXRING0_LOW or ET_INTR_RXRING1_LOW interrupt. This
interrupt is generated whenever controller notices the number of
available RX buffers are lower than pre-programmed value(
ET_RX_RING0_MINCNT and ET_RX_RING1_MINCNT register). This scheme
does not provide a way to detect when controller sees enough number
of RX buffers again such that efficient generation of XON/XOFF
frame is not easy.
While here, add more flow control related register definition.
interrupt is ours. Note, interrupts are automatically ACKed when
the status register is read.
Add RX/TX DMA error to interrupt handler and do full controller
reset if driver happen to encounter these errors. There is no way
to recover from these DMA errors without controller reset.
Rename local variable name intrs with status to enhance
readability.
While I'm here, rename ET_INTR_TXEOF and ET_INTR_RXEOF to
ET_INTR_TXDMA and ET_INTR_RXDMA respectively. These interrupts
indicate that a frame is successfully DMAed to controller's
internal FIFO and they have nothing to do with EOF(end of frame).
Driver does not need to wait actual end of TX/RX of a frame(e.g.
no need to wait the end signal of TX which is generated when a
frame in TX FIFO is emptied by MAC). Previous names were somewhat
confusing.
of a devfs file descriptor in devfs_close_f(). The passed in td argument
may be NULL if the close was invoked by garbage collection of open
file descriptors in pending control messages in the socket buffer of a
UNIX domain socket after it was closed.
PR: kern/151758
Submitted by: Andrey Shidakov andrey shidakov ru
Submitted by: Ruben van Staveren ruben verweg com
Reviewed by: kib
MFC after: 2 weeks
thread_free(newtd). This to avoid a possible page fault in
cpu_thread_clean() as seen on amd64 with syscall fuzzing.
Reviewed by: kib
MFC after: 1 week
suspend state. This will save more power.
On resume, make sure to enable all clocks. While I'm here, if
controller is not fast ethernet, enable gigabit PHY.
Don't blindly re-initialize controller whenever MTU is changed.
Now, reinitializing is done only when driver is running.
While here, remove unnecessary assignment of error value since it
was already initialized to 0.
o Do not report link status if driver is not running.
o TX/RX MAC configuration should be done with resolved speed,
duplex and flow control after establishing a link so it can't
be done in driver initialization routine.
Move the configuration to miibus_statchg callback which will be
called whenever any link state change is detected.
At this moment, flow-control is not enabled yet mainly because
I was not able to set correct flow control parameters to
generate TX pause frames.
o Now TX/RX MAC is enabled only when a valid link is detected.
Rearragnge hardware initialization routine a bit to leave
enabling MAC to miibus_statchg callback. In order to that,
TX/RX DMA engine is enabled in et_init_locked().
o Introduce ET_FLAG_LINK flag to track current link state.
o Introduce ET_FLAG_FASTETHER flag to mark whether controller is
fast ethernet. This flag is checked in miibus_statchg callback
to know whether PHY established a valid link.
o In et_stop(), TX/RX MAC is explicitly disabled instead of
relying on et_reset(). And move et_reset() from et_stop() to
controller initialization. Controler reset is not required here
and it would also clear critial registers(i.e station address,
RX filter configuration, WOL etc) that are required to make WOL
work.
o Switching to current media is done in et_init_locked() after
setting IFF_DRV_RUNNING flag. This should ensure reliable
auto-negotiation/manual link establishment.
o In et_start_locked(), check whether driver got a valid link
before trying to send frames.
o Remove checking a link in et_tick() as this is done by
miibus_statchg callback.
identifier reserved for the implementation in C99 and earlier so there is
no sensible reason for introducing yet another reserved identifier when we
could just use the one C1x uses.
Approved by: brooks (mentor)
manipulation of interrupt register access is done through
CSR_WRITE_4 macro. Also add disabling interrupt into et_reset()
because we want interrupt disabled state after controller reset.
While I'm here slightly change interrupt handler to be more
readable one.
send a single TX command after setting up all TX frames. This
removes unnecessary register accesses and bus_dmamap_sync(9) calls.
et(4) uses TX interrupt moderation so it's possible to have TX
buffers that were already transmitted but waiting for TX completion
interrupt. If the number of available TX descriptor is less then
1/3 of total TX descriptor, try reclaiming first to get enough free
TX descriptors before setting up TX descriptors.
After r228325, et_txeof() no longer tries to send frames after
reclaiming TX buffers. That change was made to give more chance
to transmit frames in main interrupt handler since we can still
send frames in interrupt handler with RX interrupt. So right
before exiting interrupt hander, after enabling interrupt, try to
send more frames. This gives slightly better performance numbers.
While I'm here reduce number of spare TX descriptors from 8 to 4.
Controller does not require reserved TX descriptors, it was just to
reduce TX overhead. After r228325, driver has much lower TX
overhead so it does not make sense to reserve 8 TX descriptors.
change should make et(4) work on any architectures.
o Remove m_getl inline function and replace it with stanard mbuf
interfaces. Previous code tried to minimize code duplication
but this came from incorrect use of common DMA tag.
Driver may be still use a common RX allocation handler with
additional structure changes but I don't see much point to do
that it would make it hard to understand the code.
o Remove DragonflyBSD specific constant EVL_ENCAPLEN, use
ETHER_VLAN_ENCAP_LEN instead.
o Add bunch of new RX status definition. It seems controller
supports RX checksum offloading but I was not able to make the
feature work yet. Currently driver checks whether recevied
frame is good one or not.
o Avoid a typedef ending in '_t' as style(9) says.
o Controller has no restriction on DMA address space, so there
is no reason to limit the DMA address to 32bit. Descriptor
rings, status blocks and TX/RX buffers now use full 64bit DMA
addressing.
o Allocate DMA memory shared between host and controller as
coherent.
o Create 3 separate DMA tags to be used as TX, mini RX ring and
stanard RX ring. Previously it created a single DMA tag and it
was used to all three rings.
o et(4) does not support jumbo frame at this moment and I still
don't quite understand how jumbo frame works on this controller
so use two RX rings to handle small sized frame and normal sized
frame respectively. The mini RX ring will be used to receive
frames that are less than or equal to 127 bytes. The second RX
ring is used to receive frames that are not handled by the first
RX ring.
If jumbo frame support is implemented, driver may have to choose
better RX scheme by letting the second RX ring handle jumbo
frames. This scheme will mimic Broadcom's efficient jumbo frame
handling feature. However RAM buffer size(16KB) of the
controller is too small to hold 2 jumbo frames, if 9KB
jumbo frame is used, I'm not sure how good performance would it
have.
o In et_rxeof(), make sure to check whether controller received
good frame or not. Passing corrupted frame to upper layer is
bad idea.
o If driver receives a bad frame or driver fails to allocate RX
buffer due to resource shortage condition, reuse previously
loaded DMA map for RX buffer instead of unloading/loading RX
buffer again.
o et_init_tx_ring() never fails so change return type to void.
o In watchdog handler, show TX DMA write back status of errored
frame which could be used as a clue to debug watchdog timeout.
o Add missing bus_dmamap_sync() in various places such that et(4)
should work with bounce buffers(e.g. PAE).
o TX side bus_dmamap_load_mbuf_sg(9) support.
o RX side bus_dmamap_load_mbuf_sg(9) support.
o Controller has no DMA alignment limit in RX buffer so use
m_adj(9) in RX buffer allocation to make IP header align on 2
bytes boundary. Otherwise it would trigger unaligned access
error in upper layer on strict alignment architectures.
One of down side of controller is it provides limited set of RX
buffer length like most Intel controllers. This is not problem
at this moment because driver does not support jumbo frame yet
but it may require alignment fixup code to support jumbo frame
on strict alignment architectures.
o In et_txeof(), don't zero TX descriptors for transmitted frames.
TX descriptors don't need write access after transmission.
Driver sets IFF_DRV_OACTIVE when the number of available TX
descriptors are less than or equal to ET_NSEG_SPARE. Make sure
to clear IFF_DRV_OACTIVE only when the number of available TX
descriptor is greater than ET_NSEG_SPARE.
__noreturn macro and modify the other exiting functions to use it.
The __noreturn macro, unlike __dead2, must be used BEFORE the function.
This is in line with the C and C++ specifications that place _Noreturn (c1x)
and [[noreturn]] (C++11) in front of the functions. As with __dead2, this
macro falls back to using the GCC attribute.
Unfortunately, clang currently sets the same value for the C version macro
in C99 and C1x modes, so these functions are hidden by default. At some
point before 10.0, I need to go through the headers and clean up the C1x /
C++11 visibility.
Reviewed by: brooks (mentor)
of vm_kmem_size that may occur if the system administrator has specified a
vm.vm_kmem_size tunable value that exceeds the hard cap.
PR: 162741
Submitted by: Adam McDougall
Reviewed by: bde@
MFC after: 3 weeks
Optimize for the case, by lazily allocating the pipe inode number at the
fstat(2) time. If alloc_unr(9) returns failure, do not fail fstat(2), since
uses of inode numbers are even rare then fstat(2), but provide zero inode
forever. Note that alloc_unr() failure is unlikely due to total number
of pipes in the system limited by the number of file descriptors.
Based on the submission by: gianni
MFC after: 2 weeks
c162516
Remove vtblk_sector_size
c162515
Wrap long license lines
c162514
Remove vtblk_unit
c162513
Wrap long lines in the license.
c162512
Remove verbose messages when link goes up/down.
A similar message is printed elsewhere as a result of
if_link_state_change().
c162511
Explicity compare pointer to NULL
c162510
Allocate the mac filter table at attach time.
c162509
Add real BSD licenses to the header files copied from Linux.
The chases upstream changes made in Linux awhile ago.
c162508
Only notify if we actually dequeued something.
c162507
Change a couple of if () { KASSERT(...) } to just KASSERTs.
In non-debug kernels, the if() { } probably get optomized
away, but I guess this is clearer.
c162506
Remove VIRTIO_BLK_F_TOPOLOGY fields in the config.
TOPOLOGY has since been removed from the spec, and the FreeBSD
didn't really do anything with the fields anyways.
c162505
Move vtblk_enqueue_request() outside the locks when getting the ident.
c162504
Remove soon to be uneeded trylock during dump [1].
http://lists.freebsd.org/pipermail/freebsd-current/2011-November/029226.html
c162503
Remove emtpy line
c162502
Drop frame if cannot allocate a vtnet_tx_header.
If we don't, we set OACTIVE, but if there are no
other frames in flight, vtnet_txeof() will never
be called to unset OACTIVE. The interface would
have to be down/up'ed in order to become usable.
We could be cuter here and only do this if the
virtqueue is emtpy, but its probably not worth
the complication.
c162501
Start mbuf replacement loop at 1 for clarity
Obtained from: Bryan Venteicher bryanv at daemoninthecloset dot org
driver that has high precedence for the controller override et(4).
Add missing callout_drain(9) in device detach and rework detach
routine. While I'm here use rman_get_rid(9) instead of using
cached resource id because bus methods are free to change the
id.
While I'm here remove initializing if_mtu, it is set by
ether_ifattach(9). Also move callout_init_mtx(9) to the right below
driver lock initialization.
descriptors before trying to send frames. If we're not able to
send a frame, make sure to prepend it to if_snd queue such that
alt(4) should work.
While I'm here prefer ETHER_BPF_MTAP to BPF_MTAP. ETHER_BPF_MTAP
should be used for controllers that support VLAN hardware tag
insertion. The controller supports VLAN tag insertion but lacks
VLAN tag stripping in RX path though.
before calling bus_enumerate_hinted_children(9) (which is the minimum for
this to work) instead of fully probing it so later on we can just call
bus_generic_attach(9) on the parent of the miibus(4) instance. The latter
is necessary in order to work around what seems to be a bzzarre race in
newbus affecting a few machines since r227687, causing no driver being
probed for the newly added miibus(4) instance. Presumably this is the
same race that was the motivation for the work around done in r215348.
Reported and tested by: yongari
- Revert the removal of a static in r221913 in order to help compilers to
produce more optimal code.
Citing jilles:
If we are ever going to do ASLR, the AUXV information tells an attacker
where the stack, executable and RTLD are located, which defeats much of
the point of randomizing the addresses in the first place.
Given that the AUXV information seems to be used by debuggers only anyway,
I think it would be good to move it to p_candebug() now.
The full virtual memory maps (KERN_PROC_VMMAP, procstat -v) are already
under p_candebug().
Suggested by: jilles
Discussed with: rwatson
MFC after: 1 week
use superpage reservations. So, for the first time, kernel virtual memory
that is allocated by contigmalloc(), kmem_alloc_attr(), and
kmem_alloc_contig() can be promoted to superpages. In fact, even a series
of small contigmalloc() allocations may collectively result in a promoted
superpage.
Eliminate some duplication of code in vm_reserv_alloc_page().
Change the type of vm_reserv_reclaim_contig()'s first parameter in order
that it be consistent with other vm_*_contig() functions.
Tested by: marius (sparc64)
Where i386/bios/apm.c requires no per-descriptor state, the ACPI version
of these device do. Instead of using hackish clone lists that leave
stale device nodes lying around, use the cdevpriv API.
On my hardware, "em" in netmap mode does about 1.388 Mpps
on one card (on an Asus motherboard), and 1.1 Mpps on another
card (PCIe bus). Both seem to be NIC-limited, because
i have the same rate even with the CPU running at 150 MHz.
On the "re" driver the tx throughput is around 420-450 Kpps
on various (8111C and the like) chipsets. On the Rx side
performance seems much better, and i can receive the full
load generated by the "em" cards.
"igb" is untested as i don't have the hardware.
A link reset now is completely transparent for the netmap client:
even if the NIC resets its own ring (e.g. restarting from 0),
the client will not see any change in the current rx/tx positions,
because the driver will keep track of the offset between the two.
2. make the device-specific code more uniform across different drivers
There were some inconsistencies in the implementation of the netmap
support routines, now drivers have been aligned to a common
code structure.
3. import netmap support for ixgbe . This is implemented as a very
small patch for ixgbe.c (233 lines, 11 chunks, mostly comments:
in total the patch has only 54 lines of new code) , as most of
the code is in an external file sys/dev/netmap/ixgbe_netmap.h ,
following some initial comments from Jack Vogel about making
changes less intrusive.
(Note, i have emailed Jack multiple times asking if he had
comments on this structure of the code; i got no reply so
i assume he is fine with it).
Support for other drivers (em, lem, re, igb) will come later.
"ixgbe" is now the reference driver for netmap support. Both the
external file (sys/dev/netmap/ixgbe_netmap.h) and the device-specific
patches (in sys/dev/ixgbe/ixgbe.c) are heavily commented and should
serve as a reference for other device drivers.
Tested on i386 and amd64 with the pkt-gen program in tools/tools/netmap,
the sender does 14.88 Mpps at 1050 Mhz and 14.2 Mpps at 900 MHz
on an i7-860 with 4 cores and 82599 card. Haven't tried yet more
aggressive optimizations such as adding 'prefetch' instructions
in the time-critical parts of the code.
difference between fi_wgen and f_seqcount, so the change is purely
cosmetic, but it makes the code easier to understand.
Submitted by: gianni
MFC after: 2 weeks
check for a UTF-8 compliant file name. Enabling this sysctl results in
an NFSv4 server that is non-RFC3530 compliant, therefore it is not enabled
by default. However, enabling this sysctl results in NFSv3 compatible
behaviour and fixes the problem reported by "dan at sunsaturn.com"
to freebsd-current@ on Nov. 14, 2011 under the subject "NFSV4 readlink_stat".
Tested by: dan at sunsaturn.com
Reviewed by: zack
MFC after: 2 weeks
pins, rather than defaulting to 0 and 1.
This way the pin order can be reversed. It is reversed with the
TP-Link TL-WR1043nd.
Submitted by: Stefan Bethke <stb@lassitu.de>
These realtek switch PHYs speak a variant of i2c with some slightly
modified handling.
From the submitter, slightly modified now that some further digging
has been done:
The I2C framework makes a assumption that the read/not-write bit of the first
byte (the address) indicates whether reads or writes are to follow.
The RTL8366 family uses the bus: after sending the address+read/not-write byte,
two register address bytes are sent, then the 16-bit register value is sent
or received. While the register write access can be performed as a 4-byte
write, the read access requires the read bit to be set, but the first two bytes
for the register address then need to be transmitted.
This patch maintains the i2c protocol behaviour but allows it to be relaxed
(for these kinds of switch PHYs, and whatever else Realtek may do with this
almost-but-not-quite i2c bus) - by setting the "strict" hint to 0.
The "strict" hint defaults to 1.
Submitted by: Stefan Bethke <stb@lassitu.de>
It appears this device fails if sent a SYNCHRONIZE_CACHE command, so add
quirk to avoid sending it.
I will follow up with Micron on this issue, and will adjust the quirk if
necessary based on their feedback.
Reviewed by: hselasky@
no need to additionally add CPU memory barriers to the acquire variants of
atomic(9), these are documented to also include compiler memory barriers.
So add the latter, which were previously included by using membar(), back.
of the same lock_owner4 string. As such, the handling of cleanup
of lock_owners could be simplified. This simplification permitted
the client to do a ReleaseLockOwner operation when the process that
the lock_owner4 string represents, has exited. This permits the
server to release any storage related to the lock_owner4 string
before the associated open is closed. Without this change, it
is possible to exhaust a server's storage when a long running
process opens a file and then many child processes do locking
on the file, because the open doesn't get closed. A similar patch
was applied to the Linux NFSv4 client recently so that it wouldn't
exhaust a server's storage.
Reviewed by: zack
MFC after: 2 weeks
having dereferenced it. We either should generally check the device_t's
supplied to bus functions before using them (which we seem to virtually
never do) or just assume that they are not NULL.
While at it make this code fit 78 columns.
Found with: Coverity Prevent(tm)
CID: 4230
when actually setting a driver as especially ENOMEM is fatal in these
cases.
- Annotate other calls to device_set_devclass(9) and device_set_driver(9)
without the return value being checked and that are okay to fail.
Reviewed by: yongari (slightly earlier version)
in addition to the user priority for threads whose current real priority
is equal to the previous user priority or if the new priority is a
real-time priority. This allows priority changes of other threads to
have an immediate effect.
MFC after: 2 weeks
According to the open firmware standard, finddevice call has to return
a phandle with value of -1 in case of error.
This commit is to:
- Fix the FDT implementation of this interface (ofw_fdt_finddevice) to
return (phandle_t)-1 in case of error, instead of 0 as it does now.
- Fix up the callers of OF_finddevice() to compare the return value with
-1 instead of 0 to check for errors.
- Since phandle_t is unsigned, the return value of OF_finddevice should
be checked with '== -1' rather than '<= 0' or '> 0', fix up these cases
as well.
Reported by: nwhitehorn
Reviewed by: raj
Approved by: raj, nwhitehorn
to known AHCI-capable chips (AMD/NVIDIA), configured for legacy emulation.
Enabled by default to get additional performance and functionality of AHCI
when it can't be enabled by BIOS. Can be disabled to honor BIOS settings if
needed for some reason.
MFC after: 1 month
NFS server and reuse it for writes as well to allow writes to the backing
store to be clustered.
- Use a prime number for the size of the heuristic table (1017 is not
prime).
- Move the logic to locate a heuristic entry from the table and compute
the sequential count out of VOP_READ() and into a separate routine.
- Use the logic from sequential_heuristic() in vfs_vnops.c to update the
seqcount when a sequential access is performed rather than just
increasing seqcount by 1. This lets the clustering count ramp up
faster.
- Allow for some reordering of RPCs and if it is detected leave the current
seqcount as-is rather than dropping back to a seqcount of 1. Also,
when out of order access is encountered, cut seqcount in half rather than
dropping it all the way back to 1 to further aid with reordering.
- Fix the new NFS server to properly update the next offset after a
successful VOP_READ() so that the readahead actually works.
Some of these changes came from an earlier patch by Bjorn Gronwall that was
forwarded to me by bde@.
Discussed with: bde, rmacklem, fs@
Submitted by: Bjorn Gronwall (1, 4)
MFC after: 2 weeks
-1. But, because ino_t is unsigned, this case was not covered by the
test ino > 0 in pipeclose(), leading to the free_unr(-1). Fix it by
explicitely comparing with 0 and -1. [1]
Do no access freed memory, the inode number was cached to prevent access
to cpipe after it possibly was freed, but I failed to commit the right
patch.
Noted by: gianni [1]
Pointy hat to: kib
MFC after: 3 days
introduced when feed-forward clock support is enabled in the kernel:
- Rename the "choice" variable to "available".
- Streamline the implementation of the "active" variable's sysctl handler
function.
- Create a kern.sysclock sysctl node for general sysclock related configuration
options. Place the "available" and "active" variables under this node.
- Create a kern.sysclock.ffclock sysctl node for feed-forward clock specific
configuration options. Place the "version" and "ffcounter_bypass" variables
under this node.
- Tweak some of the description strings.
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
defined based on WITH/WITHOUT_CTF settings, default is WITHOUT_CTF,
NO_CTF overrides WITH_CTF (used by Makefile.inc1)
- CTFCONVERT_CMD/NORMAL_CTFCONVERT are now defined to empty string
if make(1) can handle empty commands
- CTFCONVERT_CMD=... is a hack (should be defined to empty string instead):
make(1) should be taught to ignore empty commands silently in compat mode
(as it does in !compat mode, GNU make also silently ignores empty commands)
and to skip printing empty commands in !compat mode
- config(8) should generate ${NORMAL_CTFCONVERT} invocation without '@':
this will allow to simplify kern.pre.mk even more and lessen the number
of shell invocations during kernel build when CTF is turned off
- WITH_CTF can now be converted to usual MK_CTF=yes/no infrastructure
Pointy hat to: fjoe [1]
Since the address of vm_page lock mutex depends on the kernel options,
it is easy for module to get out of sync with the kernel.
No vm_page_lockptr() accessor is provided for modules. It can be added
later if needed, unless proper KPI is developed to serve the needs.
Reviewed by: attilio, alc
MFC after: 3 weeks
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
reimplementing the [get]{bin,nano,micro}[up]time() wrapper functions in terms of
the new "fromclock" API instead.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
select which system clock to obtain time from, independent of the current
default system clock. In the brave new multi sysclock world, both feedback and
feed-forward system clocks can be maintained and used concurrently, so this API
provides a minimalist first step for interested consumers to exercise control
over their choice of system clock.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
that new APIs with some performance sensitivity can be built on top of them.
These functions should not be called directly except in special circumstances.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Discussed with: Julien Ridoux (jridoux at unimelb edu au)
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
fbclock_{nanouptime|microuptime|bintime|nanotime|microtime}() functions to avoid
indirecting through a sysclock_ops wrapper function.
Committed on behalf of Julien Ridoux and Darryl Veitch from the University of
Melbourne, Australia, as part of the FreeBSD Foundation funded "Feed-Forward
Clock Synchronization Algorithms" project.
For more information, see http://www.synclab.org/radclock/
Submitted by: Julien Ridoux (jridoux at unimelb edu au)
parent interface. This avoids the overhead of queueing a packet to an IFQ
only to immediately dequeue it again.
Suggested by: np
Reviewed by: brooks
MFC after: 1 month
control for all vr(4) controllers that support it. It's known that
old vr(4) controllers(Rhine II) does not support TX pause but Rhine
III supports both TX and RX pause.
Make TX pause really work on Rhine III by letting controller know
available RX buffers.
While here, adjust XON/XOFF parameters to get better performance
with flow control.
back after I fix the breakages on some of our more exotic platforms.
While here, add the driver to the amd64 NOTES, so it can be picked up in LINT
builds.
using member variables in softc.
While I'm here change media after setting IFF_DRV_RUNNING. This
will remove unnecessary link state handling in vr_tick() if
controller established a link immediately.
have reserved free space in the APM area.
Also instead of one write request per each APM entry, use MAXPHY
sized writes when we are updating APM.
MFC after: 1 month
of hand-made.
- When registering new cloner, check whether a cloner with
same name already exist.
- When allocating unit, also check with help of ifunit()
whether such interface already exist or not. [1]
PR: kern/162789 [1]
transfer statemachine. This work is about using a single
state variable instead of multiple state bits as input
for the USB statemachine to determine what to do in the
various parts of the code. No APIs towards USB device
drivers or USB host controller drivers will be changed.
MFC after: 1 month
