causes data corruption in combination with certain bridges.
Information about this problem was kindly provided by davidch. [1]
- As BGE_FLAG_PCIX is meant to indicate that the controller is in
PCI-X mode, revert to the pre __FreeBSD_version 602101 method of
reading the bus mode register rather than checking the mere
existence of a PCI-X capability, which is also there when the
NIC f.e. is put into a 32-bit slot causing it not to be in PCI-X
mode. Setting BGE_FLAG_PCIX inappropriately could cause the NIC
to be tuned incorrectly.
PR: 128833 [1]
Reviewed by: jhb
MFC after: 3 days
When VLAN tagged frame is received the hardware sets 'LONG' bit of
Rx status word. It is always set when the size of received frame
exceeded 1518 bytes, including CRC. This VLAN tagged frame clears
'OK' bit of Rx status word such that driver should not rely on 'OK'
bit of Rx status word to pass the VLAN tagged frame to upper stack.
To fix the bug, don't use SIS_CMDSTS_PKT_OK for Rx error check and
introduce SIS_RXSTAT_ERROR macro that checks Rx errors. If we are
configured to accept VLAN tagged frames and the received frame size
is less than or equal to maximum allowed length of VLAN tagged
frame, clear 'LONG' bit of Rx status word before checking Rx
errors.
Reported by: Vladimir Ermako < samflanker <> gmail DOT com >
Tested by: Vladimir Ermako < samflanker <> gmail DOT com >
to read-locking in the TCP input path, allowing greater TCP
input parallelism where multiple ithreads or ithread and netisr
are able to run in parallel. Previously, most TCP input paths
held a write lock on the global tcbinfo lock, effectively
serializing TCP input.
Before looking up the connection, acquire a write lock if a
potentially state-changing flag is set on the TCP segment header
(FIN, RST, SYN), and otherwise a read lock. We may later have
to upgrade to a write lock in certain cases (ACKs received by the
syncache or during TIMEWAIT) in order to support global state
transitions, but this is never required for steady-state packets.
Upgrading from a write lock to a read lock must be done as a
trylock operation to avoid deadlocks, and actually violates the
lock order as the tcbinfo lock preceeds the inpcb lock held at
the time of upgrade. If the trylock fails, we bump the refcount
on the inpcb, drop both locks, and re-acquire in-order. If
another thread has freed the connection while the locks are
dropped, we free the inpcb and repeat the lookup (this should
hardly ever or never happen in practice).
For now, maintain a number of new counters measuring how many
times various cases execute, and in particular whether various
optimistic assumptions about when read locks can be used, whether
upgrades are done using the fast path, and whether connections
close in practice in the above-described race, actually occur.
MFC after: 6 weeks
Discussed with: kmacy
Reviewed by: bz, gnn, kmacy
Tested by: kmacy
incremented using in_pcbref(), and decremented using in_pcbfree()
or inpcbrele(). Protocols using only current in_pcballoc() and
in_pcbfree() calls will see the same semantics, but it is now
possible for TCP to call in_pcbref() and in_pcbrele() to prevent
an inpcb from being freed when both tcbinfo and per-inpcb locks
are released. This makes it possible to safely transition from
holding only the inpcb lock to both tcbinfo and inpcb lock
without re-looking up a connection in the input path, timer
path, etc.
Notice that in_pcbrele() does not unlock the connection after
decrementing the refcount, if the connection remains, so that
the caller can continue to use it; in_pcbrele() returns a flag
indicating whether or not the inpcb pointer is still valid, and
in_pcbfee() is now a simple wrapper around in_pcbrele().
MFC after: 1 month
Discussed with: bz, kmacy
Reviewed by: bz, gnn, kmacy
Tested by: kmacy
message for r185765.
Noted by: rdivacky
Requested by: des
Commit message for r185765 should be:
In procfs map handler, and in linprocfs maps handler, do not call
vn_fullpath() while having vm map locked. This is done in anticipation
of the vop_vptocnp commit, that would make vn_fullpath sometime
acquire vnode lock.
Also, in linprocfs, maps handler already acquires vnode lock.
No objections from: des
MFC after: 2 week
sbuf instead of doing uiomove. This allows for reads from non-zero
offsets to work.
Patch is forward-ported des@' one, and was adopted to current code
by dchagin@ and me.
Reviewed by: des (linprocfs part)
PR: kern/101453
MFC after: 1 week
does final drop of the the dq reference to put it onto the free list.
There is a possibility that the dq would be found by another thread
after sync and before the dqh lock is acquired. If that other thread
drops the dq before we have taken the dqh lock, the dirty dq is put on
the free list.
Recheck the DQ_MOD after the dqh lock is relocked. Repeat dqsync() if
the dq is dirty. This ensures that up to date dq is written in the quota
file and fixes assertion in dqget().
Reported and tested by: Frode Nordahl <frode nordahl net>
MFC after: 3 days
Waiting for 1ms for each GMII register access looks overkill and it
may also decrease overall performance of driver because re(4)
invokes mii_tick for every hz.
Tested by: rpaulo
laptops. This includes battery presence detection, charging status, current
and voltage readouts, and charge level indication. The sysctl interface
is somewhat ACPI-like.
established a valid link or not. In miibus_statchg handler add a
check for established link is valid one for the controller(e.g.
1000baseT is not a valid link for fastethernet controllers.)
o Added a flag RE_FLAG_FASTETHER to mark fastethernet controllers.
o Added additional check to know whether we've really encountered
watchdog timeouts or missed Tx completion interrupts. This change
may help to track down the cause of watchdog timeouts.
o In interrupt handler, removed a check for link state change
interrupt. Not all controllers have the bit and re(4) did not
rely on the event for a long time. In addition, re(4) didn't
request the interrupt in RL_IMR register.
Tested by: rpaulo
drivers, there should be a 1us delay after every write when
bit-banging the MII. Also insert barriers in order to ensure
the intended ordering. These changes hopefully will solve the
bus wedging occasionally experienced with DM9102A since r182461.
- Deobfuscate dc_mii_readreg() a bit.
loader_conf_files="foo bar baz"
should cause loading the files listed, and then resume with the
remaining config files (from previous values of the variable).
Unfortunately, sometimes the line was ignored -- actually even
modifying the line in /boot/default/loader.conf sometimes doesn't work.
ANALYSIS: After much investigation, turned out to be a bug in the logic.
The existing code detected a new assignment by looking at the address
of the the variable containing the string. This only worked by pure
chance, i.e. if the new string is longer than the previous value
then the memory allocator may return a different address
to store the string hence triggering the detection.
SOLUTION: This commit contains a minimal change to fix the problem,
without altering too much the existing structure of the code.
However, as a step towards improving the quality and reliability of
this code, I have introduced a handful of one-line functions
(strget, strset, strfree, string= ) that could be used in dozens
of places in the existing code.
HOWEVER:
There is a much bigger problem here. Even though I am no Forth
expert (as most fellow src committers) I can tell that much of the
forth code (in support.4th at least) is in severe need of a
review/refactoring:
+ pieces of code are replicated multiple times instead of writing
functions (see e.g. set_module_*);
+ a lot of stale code (e.g. "structure" definitions for
preloaded_files, kernel_module, pnp stuff) which is not used
or at least belongs elsewhere.
The code bload is extremely bad as the loader runs with very small
memory constraints, and we already hit the limit once (see
http://svn.freebsd.org/viewvc/base?view=revision&revision=185132
Reducing the footprint of the forth files is critical.
+ two different styles of coding, one using pure stack functions
(maybe beautiful but surely highly unreadable), one using
high level mechanisms to give names to arguments and local
variables (which leads to readable code).
Note that this code is used by default by all FreeBSD installations,
so the fragility and the code bloat are extremely damaging.
I will try to work fixing the three items above, but if others have
time, please have a look at these issues.
MFC after: 4 weeks
multiple algorithms and potentially collect multiple samples.
Instead of a single calibration interval we now have short and long
intervals; the long interval roughly corresponds to the previous
single interval. The short interval is used to speedup collection
of samples and happens much quicker. We make calls using the short
interval until we're told the calibration work is complete at which
point we fallback to the long interval. In addition there is a
much longer reset interval used to flush all calibration state and
cause everthing to start anew.
With these changes you can also disable calibration entirely by
setting the long interval to zero.
at. I don't think this will make a huge difference, but I have
received a report of a interrupt storm on one 16-bit card that this
might fix (chances are it won't, since I think that we may need to
check both the CBB registers for the 16-bit card as well as the PCIC
registers for power state change).
Submitted by: jhb@
the power interrupt and init code waiting for the interrupt are
running on different CPUs. I haven't seen this make any real
difference, but I've also had some reports of odd behavior I can't
otherwise explain. It is an infrequent operation, and certainly
wouldn't hurt.
my right mouse button and keyboard LEDs from working due to mangled
configuration packets. Fixed several other races and associated problems in the
main ADB stack that were exposed while fixing this.
Now it is possible to suspend/resume with inserted and active card.
To reinitialize card on resume and to detect card change while suspended,
implement bus rescan routines. It can also be used by controllers without
card presence detection signals or with multiple cards per slot support.
While there, cleanup msleep() usage. We have no any rights to exit without
"request done" signal from driver as it could lead to modify after free.
RTFREE_LOCKED() here. This macro makes sure the reference count
on the route is being managed properly. This elimates another
case which results in the following message being printed to the
console:
rtfree: 0xc841ee88 has 1 refs
Reviewed by: bz
MFC after: 2 weeks
bit of debugging afterwards):
- Fix protection code for notification generation.
- Decouple associd from vtag
- Allow vtags to have less strigent requirements in non-uniqueness.
o don't pre-hash them when you issue one in a cookie.
o Allow duplicates and use addresses and ports to
discriminate amongst the duplicates during lookup.
- Add support for the NAT draft draft-ietf-behave-sctpnat-00, this
is still experimental and needs more extensive testing with the
Jason Butt ipfw changes.
- Support for the SENDER_DRY event to get DTLS in OpenSSL working
with a set of patches from Michael Tuexen (hopefully heading to OpenSSL soon).
- Update the support of SCTP-AUTH by Peter Lei.
- Use macros for refcounting.
- Fix MTU for UDP encapsulation.
- Fix reporting back of unsent data.
- Update assoc send counter handling to be consistent with endpoint sent counter.
- Fix a bug in PR-SCTP.
- Fix so we only send another FWD-TSN when a SACK arrives IF and only
if the adv-peer-ack point progressed. However we still make sure
a timer is running if we do have an adv_peer_ack point.
- Fix PR-SCTP bug where chunks were retransmitted if they are sent
unreliable but not abandoned yet.
With the help of: Michael Teuxen and Peter Lei :-)
MFC after: 4 weeks
an unclean shutdown would make it impossible to mount rootfs at boot.
PR: kern/128529
Reviewed by: pjd
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
do not need any locking. Opening and closing translators is serialized
using an sx lock.
Note: This depends on the earlier fix to kern_module.c to properly order
MOD_UNLOAD events.
MFC after: 2 months
memory barriers on i386. It works as a serialization instruction on
all IA32 CPUs.
Alternative solution of using {s,l,}fence requires run-time checking
of the presense of the corresponding SSE or SSE2 extensions, and
possible boot-time patching of the kernel text.
Suggested by: many
parent threads sleep on the parent' struct proc until corresponding
child releases the vmspace. Each sleep is interlocked with proc mutex of
the child, that triggers assertion in the sleepq_add(). The assertion
requires that at any time, all simultaneous sleepers for the channel use
the same interlock.
Silent the assertion by using conditional variable allocated in the
child. Broadcast the variable event on exec() and exit().
Since struct proc * sleep wait channel is overloaded for several
unrelated events, I was unable to remove wakeups from the places where
cv_broadcast() is added, except exec().
Reported and tested by: ganbold
Suggested and reviewed by: jhb
MFC after: 2 week
move that module to the head of the associated linker file's list of modules.
The end result is that once all the modules are loaded, they are sorted in
the reverse of their load order. This causes the kernel linker to invoke
the MOD_QUIESCE and MOD_UNLOAD events in the reverse of the order that
MOD_LOAD was invoked. This means that the ordering of MOD_LOAD events that
is set by the SI_* paramters to DECLARE_MODULE() are now honored in the same
order they would be for SYSUNINIT() for the MOD_QUIESCE and MOD_UNLOAD
events.
MFC after: 1 month
unloading any modules. As a result, if any module veto's an unload
request via MOD_QUIESCE, the entire set of modules for that linker
file will remain loaded and active now rather than leaving the kld
in a weird state where some modules are loaded and some are unloaded.
- This also moves the logic for handling the "forced" unload flag out of
kern_module.c and into kern_linker.c which is a bit cleaner.
- Add a module_name() routine that returns the name of a module and use that
instead of printing pointer values in debug messages when a module fails
MOD_QUIESCE or MOD_UNLOAD.
MFC after: 1 month
interrupt code to be more robust. I've been running these changes for
over a year... With these changes, I don't see the ath card going
into reset like the code in the tree.
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.
Obtained from: Chelsio Inc.
MFC after: 3 days
o Chip full mask revision 2 or later controllers have to
set correct Tx MAC and Tx offload clock depending on negotiated
link speed.
o JMC260 chip full mask revision 2 has a silicon bug that can't
handle 64bit DMA addressing. Add workaround to the bug by
limiting DMA address space to be within 32bit.
o Valid FIFO space of receive control and status register was
changed on chip full mask revision 2 or later controllers. For
these controllers, use default 16QW as it's supposed to be the
safest value for maximum PCIe compatibility. JMicron confirmed
performance will not be reduced even if the FIFO space is set
to 16QW.
o When interface is put into suspend/shutdown state, remove Tx MAC
and Tx offload clock to save more power. We don't need Tx clock
at all in this state.
o Added new register definition for chip full mask revision 2 or
later controllers.
Thanks to JMicron for their continuous support of FreeBSD.
change. As a side effect, this makes the excessive interrupts to
disappear which has been observed as a regression in recent stable/7.
Reported by: many (on -stable@)
Reviewed by: davidch
validation code on ZFS.
Problem: when opening file with O_CREAT|O_EXCL NFS has to jump through
extra hoops to ensure O_EXCL semantics. Namely, client supplies of 8
bytes (NFSX_V3CREATEVERF) bytes of verification data to uniquely
identify this create request. Server then creates a new file with access
mode 0, copies received 8 bytes into va_atime member of struct vattr and
attempt to set the atime on file using VOP_SETATTR. If that succeeds, it
fetches file attributes with VOP_GETATTR and verifies that atime
timestamps match. If timestamps do not match, NFS server concludes it
has probbaly lost the race to another process creating the file with the
same name and bails with EEXIST.
This scheme works OK when exported FS is FFS, but if underlying
filesystem is ZFS _and_ server is running 64bit kernel, it breaks down
due to sanity checking in zfs_setattr function, which refuses to accept
any timestamps which have tv_sec that cannot be represented as 32bit
int. Since struct timespec fields are 64 bit integers on 64bit platforms
and server just copies NFSX_V3CREATEVERF bytes info va_atime, all eight
bytes supplied by client end up in va_atime.tv_sec, forcing it out of
valid 32bit range.
The solution this change implements is simple: it treats
NFSX_V3CREATEVERF as two 32bit integers and unpacks them separately into
va_atime.tv_sec and va_atime.tv_nsec respectively, thus guaranteeing
that tv_sec remains in 32 bit range and ZFS remains happy.
Reviewed by: kib
Close subtle but relatively unlikely race conditions when
propagating the vnode write error to other active sessions
tracing to the same vnode, without holding a reference on
the vnode anymore. [2]
PR: kern/126368 [1]
Submitted by: rwatson [2]
Reviewed by: kib, rwatson
MFC after: 4 weeks
boot0.S changes:
+ import a patch from Christoph Mallon to rearrange the various
print functions and save another couple of bytes;
+ implement the suggestion in PR 70531 to enable booting from
any valid partition because even the extended partitions that
were previously in our kill list may contain a valid boot loader.
This simplifies the code and saves some bytes;
+ followwing up PR 127764, implement conditional code to preserve
the 'Volume ID' which might be used by other OS (NT, XP, Vista)
and is located at offset 0x1b8. This requires a relocation of the
parameter block within the boot sector -- there is no other
possible workaround.
To address this, boot0cfg has been updated to handle both
versions of the boot code;
+ slightly rearrange the strings printed in the menus to make
the code buildable with all options. Given the tight memory
budget, this means that with certain options we need to
shrink or remove certain labels.
and especially:
make -DVOLUME_LABEL -DPXE the default options.
This means that the newly built boot0 block will preserve the
Volume ID, and has the (hidden) option F6 to boot from INT18/PXE.
I think the extra functionality is well worth the change.
The most visible difference here is that the 'Default: ' string
now becomes 'Boot: ' (it can be reverted to the old value
but then we need to nuke 1/2 partition name or entries to
make up for the extra room).
boot0cfg changes:
+ modify the code to recognise the new boot0 structure (with the
relocated options block to make room for the Volume id).
+ add two options, '-i xxxx-xxxx' to set the volume ID, -e c
to modify the character printed in case of bad input
PR: 127764 70531
Submitted by: Christoph Mallon (portions)
MFC after: 4 weeks
contrib/openbsm (svn merge) and sys/{bsm,security/audit} (manual merge).
- Add OpenBSM contrib tree to include paths for audit(8) and auditd(8).
- Merge support for new tokens, fixes to existing token generation to
audit_bsm_token.c.
- Synchronize bsm includes and definitions.
OpenBSM history for imported revisions below for reference.
MFC after: 1 month
Sponsored by: Apple Inc.
Obtained from: TrustedBSD Project
--
OpenBSM 1.1 alpha 2
- Include files in OpenBSM are now broken out into two parts: library builds
required solely for user space, and system includes, which may also be
required for use in the kernels of systems integrating OpenBSM. Submitted
by Stacey Son.
- Configure option --with-native-includes allows forcing the use of native
include for system includes, rather than the versions bundled with OpenBSM.
This is intended specifically for platforms that ship OpenBSM, have adapted
versions of the system includes in a kernel source tree, and will use the
OpenBSM build infrastructure with an unmodified OpenBSM distribution,
allowing the customized system includes to be used with the OpenBSM build.
Submitted by Stacey Son.
- Various strcpy()'s/strcat()'s have been changed to strlcpy()'s/strlcat()'s
or asprintf(). Added compat/strlcpy.h for Linux.
- Remove compatibility defines for old Darwin token constant names; now only
BSM token names are provided and used.
- Add support for extended header tokens, which contain space for information
on the host generating the record.
- Add support for setting extended host information in the kernel, which is
used for setting host information in extended header tokens. The
audit_control file now supports a "host" parameter which can be used by
auditd to set the information; if not present, the kernel parameters won't
be set and auditd uses unextended headers for records that it generates.
OpenBSM 1.1 alpha 1
- Add option to auditreduce(1) which allows users to invert sense of
matching, such that BSM records that do not match, are selected.
- Fix bug in audit_write() where we commit an incomplete record in the
event there is an error writing the subject token. This was submitted
by Diego Giagio.
- Build support for Mac OS X 10.5.1 submitted by Eric Hall.
- Fix a bug which resulted in host XML attributes not being arguments so
that const strings can be passed as arguments to tokens. This patch was
submitted by Xin LI.
- Modify the -m option so users can select more then one audit event.
- For Mac OS X, added Mach IPC support for audit trigger messages.
- Fixed a bug in getacna() which resulted in a locking problem on Mac OS X.
- Added LOG_PERROR flag to openlog when -d option is used with auditd.
- AUE events added for Mac OS X Leopard system calls.
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.
Obtained from: Chelsio Inc.
MFC after: 3 days
of the boot0.S code, with a number of compile-time selectable options,
the most interesting one being the ability to select PXE booting.
The code is completely compatible with the previous one, and with
the boot0cfg program. Even the actual code is largely unmodified,
with only minor rearrangements or fixes to make room for the new
features.
The behaviour of the standard build differs from the previous
version in the following, minor things:
+ 'noupdate' is the default, which means the code does not
write back the selection to disk. You can enable the feature
at runtime with boot0cfg, or changing the flags in the Makefile.
+ a drive number of 0x00 (floppy, or USB in floppy emulation) is
now accepted as valid. Previously, it was overridden with 0x80,
meaning that the partition table coming from the media was
used to access sectors on a possibly different media.
You can revert to the previous mode building with -DCHECK_DRIVE,
and you can always use the 'setdrv' option in boot0cfg
+ certain FAT or NTFS partitions are listed as WIN instead of DOS.
+ the 'bel' character on a bad selection is replaced by a '#' to
make it clear that the system is not hang even if the machine
does not have a speaker. This can be reverted back at compile
time, or at runtime with an upcoming boot0cfg option.
Additional features are available as compile time options,
and may be become the default if deemed useful. In particular:
+ INT18/PXE boot (make -DPXE)
This option enables booting through INT 18h (which on certain
BIOSes can be hooked to PXE) by pressing F6. There is unfortunately
no room to print the additional menu option.
Also, to make room for the code, the 'Default: ' string is
changed to 'Boot: '
+ print current drive number (make -DTEST)
Prints a line indicating the current drive number.
This is useful to figure out what is going on for machines/bioses
which remap drives in sometimes surprising ways.
+ disable numeric keys in console mode (make -DONLY_F_KEYS)
Not really a significant option, but it is needed to make
room for the -DTEST mode.
+ disable floppy support (make -DCHECK_DRIVE)
Revert to the old behaviour of only accepting 0x80 and above
as valid drive numbers.
MFC after: 6 weeks
