the falling edge of a media state change.
This is in preparation for media state change notification to the
routing socket.
No objections by: sam, wpaul, ru, bms
Brucification by: bde
MAC address in the EEPROM, and we need to get it from OpenFirmware.
This isn't very pretty but time is lacking to do this in a better
way this near 5.2-RELEASE. This is a RELENG_5_2 candidate.
Original version by: Marius Strobl <marius@alchemy.franken.de>
Tested by: Pete Bentley <pete@sorted.org>
Reviewed by: jake
frame, not the first. It is probably also not safe to free the mbuf chain
as soon as the OWN bit is cleared on the first descriptor since the chip
may not be done copying the frame into the transmit FIFO. Revert the part of
of busdma conversion (if_dc.c rev 1.115) which changed dc_txeof() to look for
the status in the first descriptor and free the mbuf chain when processing
the first descriptor for the frame, and revert the matching changes elsewhere
in the driver. This part of the busdma change caused the driver to report
spurious collisions and output errors, even when running in full-duplex mode.
Reverting the mbuf chain handling slightly complicates dc_dma_map_txbuf(),
since it is responsible for setting the OWN bits on the descriptors, but does
not normally have direct access to the mbuf chain.
Tested by:
Dejan Lesjak <dejan.lesjak at ijs.si> alpha/<Intel 21143 10/100BaseTX>
"Xin LI" <delphij at frontfree.net> i386/<Macronix 98713 10/100BaseTX>
Wiktor Niesiobedzki <bsd at w.evip.pl> i386/<3Com OfficeConnect 10/100B>
Reviewed by: mux
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
chain passed into dc_encap, which dc_start was unaware of. This caused
the old (now invalid) mbuf to be passed to BPF_MTAP.
Spotted by: Kenjiro Cho <kjc@csl.sony.co.jp>
for 21143 based cards which use SIA mode.
This fixes 10mbit mode for ZNYX ZX346Q cards and other
21143 based cards.
PR: 32118
Submitted by: Rene de Vries <rene@tunix.nl>
Geert Jan de Groot <GeertJan.deGroot@tunix.nl>
Obtained from: BSDI
MFC after: 2 weeks
that has been recorded earlier and overwrite it again later by
reading it directly from the EEPROM again.
Read the MAC address from the PAR0/PAR1 registers instead, which
are autoloaded on reboot.
Tested on AN985, AN983B. According to the datasheets, it should
also work for the AL981 (I don't have such a chip on a card at home)
PR: 52988
Submitted by: Andrew Gordon <arg-bsd@arg.me.uk>
MFC after: 2 weeks
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
bzero(ptr, sizeof(DC_RXLEN * 5));
which should obviously be:
bzero(ptr, DC_RXLEN * 5);
Looks like this bug may have reduced the effectiveness of the
workaround for the hardware bug in the PNIC chips.
MFC after: 1 week
o Remove register keyword
o ANSIfy prototypes
o Remove "return;" at the end of void functions
o Remove trailing spaces
o Don't align local variables with tabs and reorder them
o Don't use /* FOO */ at the end of a #ifdef FOO block if
it's a small block
- Other non-functional changes :
o 6 -> ETHER_ADDR_LEN
o Don't initialize if_output; ether_ifattach() does it for us
The submitter of PR 32118 told me that this patch also fixes autoselecting
for znyx 4 port cards (10baseT, 100baseTX did work already).
PR: 32118
Reviewed by: imp
Approved by: rwatson (re)
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
in dc_detach() instead of only calling it if the hardware is preset.
This is a workaround for page faults in softclock() after a `dc'
device was detached, caused by not disabling a timer before freeing
its memory. The bus_child_present() checks should probably be
re-added later, but only to avoid the hardware accesses and not the
other resource cleanups in dc_stop().
Approved by: njl
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
