allow them to start after netif. There were too many problems reported
with this change in the short period of time that it lived in HEAD, and
we are too late in the release cycle to properly shake it out.
IMO the issue of having the firewalls up before the network is still a
valid concern, particularly for pf whose default state is wide open.
However properly solving this issue is going to take some investment
on the part of the people who actually use those tools.
This is not a strict reversion of all the changes for r193198 since it
also included some simplification of the BEFORE/REQUIRE logic which is
still valid for ipfilter and ip6fw.
the interface name of interfaces that were configured.
This change has the added benefit that ifn_start() and
ifn_stop() in network.subr no longer write to standard output.
Whether to output and what to output is now handled entirely
in rc.d/netif.
non-dhcp interfaces to negotiate/associate this will make more sense.
This also correctly gets run after both devd and netif are run so it has
a chance of working.
To preserve the existing behavior of etc/rc.d/netif, add code to wait
up to if_up_delay seconds (30 seconds by default) for a default route to
be configured if there are any dhcp interfaces. This should be extended
to test that the interface is actually up.
X-MFC after:
out because the rc.conf(5) variable was not enabled. Display a
message that the command wasn't run and offer suggestions on
what the user can do.
Implement a quiet prefix, which will disable some diagnostics. The
fast prefix also implies quiet. During boot we use either fast or
quiet. For shutdown we already use 'faststop'. So, this informational
message should only appear during interactive use.
An additional benefit of having a quiet prefix is that we can start
putting some of our diagnostic messages behind this knob and start
"de-cluttering" the console during boot and shutdown.
wpa_supplicant and other programs started by 'netif' don't get erased
by a subsequent 'cleanvar'.
Approved by: re (bmah)
Reviewed by: dougb
MFC after: 1 week
and takes over mountcritlocal's role as the early / late divider. This
makes it far easier to add rc scripts which need to run early, such as a
startup script for zfs, which is right around the corner.
This change should be a no-op; I have verified that the only change in
rcorder's output is the insertion of FILESYSTEMS immediately after
mountcritlocal.
MFC after: 3 weeks
Note: This also deprecates "NO" as a way to specify an empty list of
interfaces for gif_interfaces.
PR: conf/104884
Submitted by: nork
Harassed by: brd
Discussed with: brooks, dougb
scripts, except for mdconfig* and jail. Such symbols are reserved
for the rc.subr internals. Most scripts can be fixed by just
declaring _foo symbols as local: few scripts actually need them to
be global.
Discussed with: dougb in freebsd-rc
automaticly add it to an Ethernet bridge. This is intended for applications
such as qemu, vmware, openvpn, ... which open tap interfaces and need them
bridged with the hosts network adapter, the user can set up a glob for
interfaces to be automatically added (eg tap*).
more IPv4 address from a ranged list in CIRD notation:
ipv4_addrs_ed0="192.168.0.1/24 192.168.1.1-5/28"
In the process move alias processing into new ipv4_up/down functions to
more toward a less IPv4 centric world.
Submitted by: Philipp Wuensche <cryx dash freebsd at h3q dot com>
them. Just try to run the given command on them. We need to be able to
run stop functions on interfaces that have been deleted to stop
wpa_supplicant.
Approved by: re (interface startup blanket)
way interfaces are configured. Some key points:
- At startup, all interfaces are configured through /etc/rc.d/netif.
- ifconfig_<if> variables my now mix real ifconfig commands the with
DHCP and WPA directives. For example, this allows media
configuration prior to running dhclient.
- /etc/rc.d/dhclient is not run at startup except by netif to start
dhclient on specific interfaces.
- /etc/pccard_ether calls "/etc/rc.d/netif start <if>" to do most of
it's work.
- /etc/pccard_ether no longer takes additional arguments to pass to
ifconfig. Instead, ifconfig_<if> variables are now honored in favor
of pccard_ifconfig when available.
- /etc/pccard_ether will only run on interfaces specified in
removable_interfaces, even if pccard_ifconfig is set.
than one interface from the command line:
# /etc/rc.d/netif start bfe0 xl0
It's also possible to restart an interface(s):
# /etc/rc.d/netif restart bfe0
This required some changes to rc.subr(8) so that if the start/stop commands
are overidden the rest of the command line (after the start/stop/etc... cmd)
is passed through to the subroutines.
network interfaces could only be turned on and off as a group (all
static interfaces or all dhcp interfaces).
When used to start the interface a 'long form' ifconfig output is
used to show the status of the interface, but when stopping an interface
the script will simply output the name of the interface. This is simply my
personal preference. Hopefully as this functionality matures we can
stabilize on a prefered form of output for these scripts.
A stop command to the dhclient script now explicitly releases the dhcp lease.
Behaviour at system shutdown; however, is unchanged since dhclient is not,
by default, run at that time. The client will not release its lease
at shutdown.
o /etc/network.subr contains common subroutines used for seting
up network interfaces
o rc.d/hostname sets the hostname if not already set
o rc.d/nisdomain sets the nis domain *after* rpcbind but
before the yp* daemons. This fixes issues with temporary
hangs when looking up informaion in nis before it's ready.
o rc.d/netif brings network interfaces (minus dhcp) up.
o rc.d/network1 has been disabled and will be retired before
RELENG_5. It will be replaced by rc.d/netif
Approved by: markm (mentor)
