In order to make this work, I created a pseudo-PHY driver to deal with
Macronix chips that use the built-in NWAY support and symbol mode port.
This is actually all of them, with the exception of the original MX98713
which presents its NWAY support via the MII serial interface.
The mxphy driver actually manipulates the controller registers directly
rather than using the miibus_readreg()/miibus_writereg() bus interface
since there are no MII registers to read. The mx driver itself pretends
that the NWAY interface is a PHY locayed at MII address 31 for the sole
purpose of allowing the mxphy_probe() routine to know when it needs to
attach to a host controller.
similar to the PNIC I (supported by the pn driver). In fact, it's really
a Macronix 98715A with wake on LAN support added. According to LinkSys,
the PNIC II was jointly developed by Lite-On and Macronis. I get the
feeling Macronix did most of the work. (The datasheet has the Macronix
logo on it, and is in fact nearly identical to the 98715 datasheet, except
for the extra wake on LAN registers.) In any case, the PNIC II works just
fine with the Macronix driver.
The changes are:
- Move PCI ID for the PNIC II from the pn driver to the mx driver.
- Mention PNIC II support in mx.4.
- Mention PNIC II support in RELNOTES.TXT and HARDWARE.TXT.
preparation for tsunami support. Previous chipsets' direct-mapped DMA
mask was always 1024*1024*1024. The Tsunami chipset needs it to be
2*1024*1024*1024
These changes should not affect the i386 port
Reviewed by: Doug Rabson <dfr@nlsystems.com>
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
Like the PNIC, we have to copy packet headers in the receive handler
because the chip will only DMA to longword aligned buffers.
Also do some mindor cleanups.
during a trek through RCS. The Macronix 98713 and 98713A both have the
same PCI device ID but different revision numbers, and we need to be
able to tell one from the other. The 98715 and 98715A chips have the
same device ID as the 98725 chip but different revision numbers, however
we lump them into the same category except when identifying them during
the PCI probe output.
The main reason we need tell the chips apart is that the Macronix app
notes say you have to write a special magic number into one of the
registers in order to put the chip in normal operating mode. The 98713
requires one magic value, while all the others require a different one.
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
