all the other bt_XXX() functions in i386/scsi/bt*.
This the important effect of forcing a link error if the user is
still using the old "vector btintr" which is dangerously wrong
after Justin's updates to the driver.
The correct isa vector line for the bt driver is "vector bt_isa_intr".
Justin mentioned this in the commit message and updated LINT and
GENERIC. This change is to enforce that.. :-)
seems to work hre just fine though I can't check every file
that changed due to limmited h/w, however I've checked enught to be petty
happy withe hte code..
WARNING... struct lkm[mumble] has changed
so it might be an idea to recompile any lkm related programs
all buses.
Known problems:
-The PCI probe code has not been tested. Someone with a PCI Bt card will
have to validate it, but even if it is broken all cards the earlier version
of this driver found in ISA compatibility mode should still be found.
-Still missing the BT956 PCI ID, so it will be found as an ISA card until
someone suplies it.
-PCI interrupts go through an interrupt stub that returns an int until
we remove the edge-triggered PCI compatibiliity cruft.
-ISA interrupts go through an interrupt stub until they pass in (void *).
-The driver could support more mboxes and concurrent commands by allocating
structures separately and hanging them off the bt_data struct to get around
the 4K page limit. Someone with documentation should do this and also
enable tagged queuing.
can be found in ISA compatibility mode by the ISA driver, but since the
EISA and PCI probes are non-invasive, we prefer them to find the card first.
Since both EISA and PCI probes can rely on interrupts, enable them before
probing of any type is performed. All ISA probes are still "protected" by
splhigh().
allow one EISA/ISA/PCI/VL Buslogic controller to be probed. The driver
is almost fully dynamic. It just needs some kdc work and for the SCSI code
to stop passing unit numbers up in the scsi_xfer struct.
device must be configured. It's hard to tell whether a reset function
should be noreset or nullreset since reset functions are never called.
Most drivers use nullreset but noreset has the advantage of complaining
if somehow gets called).
Removed old aliases d_rdwr_t and d_ttycv_t for d_read_t/d_write_t and
d_devtotty_t.
Sorted declarations of switch functions into switch order.
Removed duplicated comments and declarations of nonexistent switch
functions.
most devsw referenced functions are now static, as they are
in the same file as their devsw structure. I've also added DEVFS
support for nearly every device in the system, however
many of the devices have 'incorrect' names under DEVFS
because I couldn't quickly work out the correct naming conventions.
(but devfs won't be coming on line for a month or so anyhow so that doesn't
matter)
If you "OWN" a device which would normally have an entry in /dev
then search for the devfs_add_devsw() entries and munge to make them right..
check out similar devices to see what I might have done in them in you
can't see what's going on..
for a laugh compare conf.c conf.h defore and after... :)
I have not doen DEVFS entries for any DISKSLICE devices yet as that will be
a much more complicated job.. (pass 5 :)
pass 4 will be to make the devsw tables of type (cdevsw * )
rather than (cdevsw)
seems to work here..
complaints to the usual places.. :)
for the particular card in use. At the moment, I've set it to any of
the bt445S VLB cards (not the bt445C which apparently work) and the
bt5xx series (isa cards). The 742 and PCI cards should not need it. :-)
It may be useful to have something like this:
#ifndef BOUNCE_BUFFERS
if (bounce_buffers_required && more_than_16MB_ram)
panic("this card requires bounce buffers for more than 16MB ram!")
#endif
to get the definitions of TRUE and FALSE which happen to be defined in
a deeply nested include.
Added nearby #includes of <sys/conf.h> where appropriate.
is not real helpful since swapgeneric.c doesn't seem to be used, except
perhaps on a GENERIC kernel. (Sorry Paul.. :-)
I've moved it from swapgeneric.c to autoconf.c, since autoconf.c also deals
with dumpdev things. There may be a better place.....
but probably harmless. It's hard to tell because apparently no one runs
ity.
Fixed ity's d_reset entry. `nx' entries should never be used for existing
devices.
conf.c:
Moved a prototype to a better place.
Removed a stale #define.
